The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner. Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:
tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5
Now, instead of reporting an invalid ID, it will report the correct error:
tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed
Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.
With this patch, it will now print:
Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio.c
em28xx-dvb.c
- Em28xx extensions should ensure they are being only loaded against devices
that support them. Deals with case where there are multiple em28xx
devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
- DVB support is supposed to be enabled for the first generation HVR-900.
This device was confirmed with DVB by mkrufky when we did the original work
in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-video.c
- Properly handle loading of the module when multiple devices are already
connected (such as at bootup). Before we were only calling dvb_init()
against the last device in the list, so while we were handling subsequent
adds properly, if there were multiple devices present on driver load,
everybody except the last device would not get initialized.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18-cards.h had a copy of the audio and video input enums
from cx18-av-core.h, but with different prefixes. Removed
that copy and used the ones from cx18-av-core.h.
Thanks to Andy Walls <awalls@radix.net> for the report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improve the documentation of how to use the rfkill class in kernel drivers,
based on the doubts that came up in a thread in linux-wireless.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current naming of rfkill_state causes a lot of confusion: not only the
"kill" in rfkill suggests negative logic, but also the fact that rfkill cannot
turn anything on (it can just force something off or stop forcing something
off) is often forgotten.
Rename RFKILL_STATE_OFF to RFKILL_STATE_SOFT_BLOCKED (transmitter is blocked
and will not operate; state can be changed by a toggle_radio request), and
RFKILL_STATE_ON to RFKILL_STATE_UNBLOCKED (transmitter is not blocked, and may
operate).
Also, add a new third state, RFKILL_STATE_HARD_BLOCKED (transmitter is blocked
and will not operate; state cannot be changed through a toggle_radio request),
which is used by drivers to indicate a wireless transmiter was blocked by a
hardware rfkill line that accepts no overrides.
Keep the old names as #defines, but document them as deprecated. This way,
drivers can be converted to the new names *and* verified to actually use rfkill
correctly one by one.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the documentation so as to make sure driver writers understand
exactly where the boundaries are for input drivers related to rfkill
switches, buttons and keys, and rfkill class drivers.
Also fix a small error in the documentation: setting the state of a normal
instance of the rfkill class does not affect the state of any other devices
(unless they are tied by firmware/hardware somehow).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SW_RFKILL_ALL is the "emergency power-off all radios" input event. It must
be handled, and must always do the same thing as far as the rfkill system
is concerned: all transmitters are to go *immediately* offline.
For safety, do NOT allow userspace to override EV_SW SW_RFKILL_ALL OFF. As
long as rfkill-input is loaded, that event will *always* be processed, and
it will *always* force all rfkill switches to disable all wireless
transmitters, regardless of user_claim attribute or anything else.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The whole current_state thing seems completely useless and a source of
problems in rfkill-input, since state comparison is already done in rfkill,
and rfkill-input is more than likely to become out of sync with the real
state.
Signed-off-by: Fabien Crespel <fabien@crespel.net>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the notification chains to also send uevents, so that userspace can be
notified of state changes of every rfkill switch.
Userspace should use these events for OSD/status report applications and
rfkill GUI frontends. HAL might want to broadcast them over DBUS, for
example. It might be also useful for userspace implementations of
rfkill-input, or to use HAL as the platform driver which promotes rfkill
switch change events into input events (to synchronize all other switches)
when necessary for platforms that lack a convenient platform-specific
kernel module to do it.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will need access to the rfkill switch type in string format for more
than just sysfs. Therefore, move it to a generic helper.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a notifier chain for use by the rfkill class. This notifier chain
signals the following events (more to be added when needed):
1. rfkill: rfkill device state has changed
A pointer to the rfkill struct will be passed as a parameter.
The notifier message types have been added to include/linux/rfkill.h
instead of to include/linux/notifier.h in order to avoid the madness of
modifying a header used globally (and that triggers an almost full tree
rebuild every time it is touched) with information that is of interest only
to code that includes the rfkill.h header.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The resume handler should reset the wireless transmitter rfkill
state to exactly what it was when the system was suspended. Do it,
and do it using the normal routines for state change while at it.
The suspend handler should force-switch the transmitter to blocked
state, ignoring caches. Do it.
Also take an opportunity shot to rfkill_remove_switch() and also
force the transmitter to blocked state there, bypassing caches.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unfortunately, instead of adding a generic Wireless WAN type, a technology-
specific type (WiMAX) was added. That's useless for other WWAN devices,
such as EDGE, UMTS, X-RTT and other such radios.
Add a WWAN rfkill type for generic wireless WAN devices. No keys are added
as most devices really want to use KEY_WLAN for WWAN control (in a cycle of
none, WLAN, WWAN, WLAN+WWAN) and need no specific keycode added.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Iñaky Pérez-González <inaky.perez-gonzalez@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, rfkill support for read/write rfkill switches is hacked through
a round-trip over the input layer and rfkill-input to let a driver sync
rfkill->state to hardware changes.
This is buggy and sub-optimal. It causes real problems. It is best to
think of the rfkill class as supporting only write-only switches at the
moment.
In order to implement the read/write functionality properly:
Add a get_state() hook that is called by the class every time it needs to
fetch the current state of the switch. Add a call to this hook every time
the *current* state of the radio plays a role in a decision.
Also add a force_state() method that can be used to forcefully syncronize
the class' idea of the current state of the switch. This allows for a
faster implementation of the read/write functionality, as a driver which
get events on switch changes can avoid the need for a get_state() hook.
If the get_state() hook is left as NULL, current behaviour is maintained,
so this change is fully backwards compatible with the current rfkill
drivers.
For hardware that issues events when the rfkill state changes, leave
get_state() NULL in the rfkill struct, set the initial state properly
before registering with the rfkill class, and use the force_state() method
in the driver to keep the rfkill interface up-to-date.
get_state() can be called by the class from atomic context. It must not
sleep.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, radios are always enabled when their rfkill interface is
registered. This is not optimal, the safest state for a radio is to be
offline unless the user turns it on.
Add a module parameter that causes all radios to be disabled when their
rfkill interface is registered. The module default is not changed so
unless the parameter is used, radios will still be forced to their enabled
state when they are registered.
The new rfkill module parameter is called "default_state".
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teach rfkill-input how to handle SW_RFKILL_ALL events (new name for the
SW_RADIO event).
SW_RFKILL_ALL is an absolute enable-or-disable command that is tied to all
radios in a system.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a minor typo in an exported function documentation
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill really should have been named rfswitch. As it is, one can get
confused whether RFKILL_STATE_ON means the KILL switch is on (and
therefore, the radio is being *blocked* from operating), or whether it
means the RADIO rf output is on.
Clearly state that RFKILL_STATE_ON means the radio is *unblocked* from
operating (i.e. there is no rf killing going on).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: arch/x86/mm/built-in.o(.text+0x3a1): Section mismatch in
reference from the function set_pte_phys() to the function
.init.text:spp_getpage()
The function set_pte_phys() references
the function __init spp_getpage().
This is often because set_pte_phys lacks a __init
annotation or the annotation of spp_getpage is wrong.
arch/x86/mm/init_64.c: In function 'early_memtest':
arch/x86/mm/init_64.c:520: warning: passing argument 2 of
'find_e820_area_size' from incompatible pointer type
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Cc: "Linus Torvalds" <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
native_read_tscp shifts the bits in the high order value in the
wrong direction, the attached patch fixes that.
Signed-off-by: Max Asbock <masbock@linux.vnet.ibm.com>
Acked-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar wrote:
> -tip auto-testing started triggering this spinlock corruption message
> yesterday:
>
> [ 3.976213] calling acpi_rtc_init+0x0/0xd3
> [ 3.980213] ACPI Exception (utmutex-0263): AE_BAD_PARAMETER, Thread F7C50000 could not acquire Mutex [3] [20080321]
> [ 3.992213] BUG: spinlock bad magic on CPU#0, swapper/1
> [ 3.992213] lock: c2508dc4, .magic: 00000000, .owner: swapper/1, .owner_cpu: 0
This is apparently because some parts of ACPI, including mutexes, are not
initialized when acpi=off is passed to the kernel.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A bug in libsensors <= 2.10.6 is exposed
when this new hwmon I/F is enabled.
Create CONFIG_THERMAL_HWMON=n
until some time after libsensors 2.10.7 ships
so those users can run the latest kernel.
libsensors 3.x is already fixed -- those users
can use CONFIG_THERMAL_HWMON=y now.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch fixes pxafb's init/exit annotations. It uses __devinit/exit for
probe functions and __init for init functions. g_options is left as
__devinitdata since it is used by both.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The esp driver currently does hand rolled reference counting of its
target. It's much easier to do what it needs to do if it's plugged into
the mid-layer callbacks (target_alloc and target_destroy) which were
designed for this case, so do it this way and get rid of the internal
target reference count.
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch modifies the band selection management when scanning, so
bands are now scanned according to HW band support.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb_cache_mutex was not correctly released
under all circumstances. Both rt73usb as rt2500usb
didn't release the mutex under certain conditions
when the register access failed. Obviously such
failure would lead to deadlocks.
In addition under similar circumstances when the
bbp register couldn't be read the value must be
set to 0xff to indicate that the value is wrong.
This too didn't happen under all circumstances.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible NULL pointer dereference in an error path of the
DMA allocation error checking code. This is also necessary for a future
DMA API change that is on its way into the mainline kernel that adds
an additional dev parameter to dma_mapping_error().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a possible MMIO access while the device is still down
from a suspend cycle. MMIO accesses with the device powered down
may cause crashes on certain devices.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Never return TX_BUSY from op_tx. It doesn't make sense to return
TX_BUSY, if we can not transmit the packet.
Drop the packet and return TX_OK.
This will fix the resume hang.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement missing EU regulatory domain for mac80211. Based on the
information in IEEE 802.11-2007 (specifically pages 1142, 1143 & 1148)
and ETSI 301 893 (V1.4.1).
With thanks to Johannes Berg.
Signed-off-by: Tony Vroon <tony@linx.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
