drivers/net/sb1000.c has lots of inlined static functions.
Mst of them are used at initialization, wait for some
hardware register to change (wait using yield, sleep etc),
or do slow port-based I/O. Inlining thse "for speed" makes no sense.
This patch removes "inline" from biggest static function
(regardless of number of callsites - gcc nowadays auto-inlines
statics with one callsite).
Size difference for 32bit x86:
text data bss dec hex filename
6299 129 0 6428 191c linux-2.6-ALLYES/drivers/net/sb1000.o
5418 129 0 5547 15ab linux-2.6.inline-ALLYES/drivers/net/sb1000.o
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch #if 0's the no longer used netxen_nic_link_ok().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Problem: If setting of an ip-address fails with LAN_OFFLINE,
qeth does not save the ip-address in its internal
list of set ip-addresses. qeth recovers after a
following STARTLAN event, but cannot set the unsaved
ip-address.
Solution: save the ip-address in the qeth-maintained list of
ip-addresses after a LAN_OFFLINE failure for SETIP.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Allocate headroom for TR_HLEN but using only ETH_HLEN causes rx
performance degradation. Allocate ETH_HLEN for ethernet and
TR_HLEN for token ring (layer 3 mode).
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Improving debug message handling, moving ipa into messages from kernel
to dbf, some cleanups and typo fixes.
Signed-off-by: Peter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Symptom: slow CCL response time
Problem: non-ETH_P_802_2 packets are not delivered to NDH for
CCL. But CCL detects missing sequence numbers, which
cause a serious performance problem with CCL.
Solution: assign sequence numbers only to 802.2 packets.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Problem: A STARTLAN command from the adapter may arrive while a
qeth recovery is currently running with a failed qeth
STARTLAN. Usually qeth schedules a recovery when
receiving a STARTLAN command from the adapter. But
another recovery scheduled while a recovery is already
running never starts. Thus the qeth-administered
lan_online flag remains zero in this scenario, even
though the adapter-STARTLAN has happened.
Solution: Set lan_online flag for a received STARTLAN from the
adapter in case scheduled recovery does not start.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
OSA-adapters do not have an address limitation for the qdio queue
structures except the MAX storage level of the current processor.
And due to a recent z/VM APAR there is no longer a restriction to
allocate qdio structures below 2 GB.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1. ip_list handling after deregister failure of multicast address:
If error code "MC Address not found" is returned do not re-add
multicast address to ip_list.
For other error codes readd multicast address at the end of
function qeth_delete_all_mc.
2. ip_list handling after deregister failure or normal ip address:
If error code "IP Address not found" is returned do not re-add
multicast address to ip list.
This is especially important in IP address takeover scenarios,
to enable re-takeover of a taken over IP address.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The register tests should be run with all the proper flags enabled
to maximize the test coverage code and make sure we are as close
as we can get to testing regular traffic.
Reformat the code for readability. Minor cleanups in the descriptor
ring setup.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several minor cosmetic function renames.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With multiple queues coming into the code these base control
registers need to be made into arrays.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use netdev_alloc_skb since it handles any NUMA node memory localtion issues
and sets skb->dev. Since device driver was not setting skb->dev, I bet
filter rules based on device would not work.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Any negative return value from start_xmit is interpreted as NETDEV_TX_LOCK
which is not what this driver wants. It should return 0 (NETDEV_TX_OK)
when it consumes a packet.
Also, use skb_padto() as the generic way to pad small frames.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Statistics structure is available for use in net_device structure.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch works around the MWI bug on the DC21143 rev 65 Tulip by
ensuring that the receive buffers don't end on a cache line boundary
(as documented in the errata).
This patch is required for the MIPS based Cobalt Qube/RaQ as
supporting the extra PCI commands seems to reduce the chance of a hard
lockup between the Tulip and the PCI bridge.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
winbond-840 shares tulip.h with the tulip driver, because they share
many (but not all) of the same register definitions.
This is useful for the register definitions, but not helpful when it
comes to symbols that are shared among the tulip driver's C modules,
but not meant to be shared outside that one driver.
Thus, PKT_BUF_SZ is a symbol internal to tulip, but it was intruding
upon a similar symbol in winbond-840's namespace. This was not a
problem as long as the two symbols had the same value, but upcoming
patches result in differing symbol values.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Multi-line comments weren't all CodingStyle compliant
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Having the id field be an int was making more complex bus topologies
excessively difficult. For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Poll the completed TX frames in gfar_poll(). This prevents the tx
completion interrupt from interfering with processing of received
frames.
We also disable hardware rx coalescing when NAPI is enabled.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch revises the logging for link informations of spidernet.
- The link down message is too verbose because auto-negotiation timeout
occurs periodically while an ethernet cable is not connected.
- We want to see the link result, and we think it should be displayed.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In addition to the value of GHIINT0STS, spidernet interrupt handler
should check the values of GHIINT1STS/GHIINT2STS registers at the
beginning of spider_net_interrupt() so as not to drop error
interrupts.
GHIINT1STS/GHIINT2STS registers indicates some of erroneous conditions
in spidernet, and a few bits of GHIINT0STS register reflects these
conditions. But GHIINT0MSK masks these bits, so you should check these
conditions by reading GHIINT1STS/GHIINT2STS registers directly.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes spidernet interrupt masks.
- unmask GDAINVAINT. There is an operation to do by spidernet
interrupt handler.
- mask some interrupts. There are no operations in the interrupt handler.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch extends the timeout for spidernet auto-negotiation.
Auto-negotiation often fails to finish in 2 seconds.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes initialization of "aneg_count" and "medium" fields in
spider_net_card to make spidernet driver correctly sets "link status".
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cosmetic TAB/whitespace cleanups and some style cleanups. No
functional changes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Convert the tc35815 driver to use the generic PHY layer in
drivers/net/phy. Also rename 'boardtype' to 'chiptype' which hould be
more appropriate.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use struct net_device_stats embedded in struct net_device.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When there are multiple mv643xx_eth silicon blocks in the system,
don't print an initialisation message for each and every one of
them.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Pass a struct mv643xx_private * to the register accessor functions,
as a preparation for having multiple mv643xx_eth silicon blocks.
(Since this causes some 80 column straddling, and the mv_ prefix
is useless anyway, rename mv_read to rdl and mv_write to wrl to
compensate.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
In error and warning printks, always report the netdevice name
instead of the port index (the latter has no meaning when there
are multiple mv643xx_eth silicon blocks in the system.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Instead of identifying individual mv643xx ethernet ports by only
their port number, identify them by their struct mv643xx_private *,
as just a port number has no meaning when there are multiple
mv643xx_eth silicon blocks in the system.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
- Remove unused MV643XX_DEFAULT_[RT]X_QUEUE_SIZE definitions.
- Remove ETH_TARGET enum -- it isn't used anywhere in the driver,
and isn't even valid for non-mv643xx chip models, as those use
different MBUS target IDs.
- Clean up comment and control flow in mv643xx_eth_change_mtu().
- Use mp->dev instead of mp->mii.dev in mv643xx_eth_tx_timeout_task().
- Make mv643xx_eth_free_tx_descs() static.
- Remove overzealous NULL check in mv643xx_eth_start_xmit().
- Use symbolic NETDEV_TX_* constants in mv643xx_eth_start_xmit().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
When we moved to arch/powerpc we actively tried to avoid using the
ppc_md.setup_io_mappings(). Currently no board ports use it so let's
remove it to avoid any new boards using it.
Also, remove early_serial_map() since we don't even have a call out for
it in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is logic in platforms/peries/lpars.c which checks if the user has
specified a console on the command line, and refrains from adding a
preferred console entry for the hvc/hvsi console if they have.
This trips up if you use "netconsole=foo" on the command line, and has
the result that you get _only_ the netconsole, because the hvc device is
never added as a preferred console. Worse still if you get the netconsole
configuration wrong somehow, you end up with no console at all.
As it turns out we don't need to worry about checking the command line.
If the user has specified "console=foo", then foo will be set as the
preferred console when the command line is parsed in start_kernel(), much
later than the pseries code, and so the latter setting will take effect.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the prototype for find_udbg_vterm() into pseries.h, removing
it from setup.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Describe noraid parameter with its name (and not its value).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The header files for the Pb1200/DBAu1200 boards have wrong definition for the
IDE interface's decoded range length -- it should be 512 bytes according to
what the IDE driver does. In addition, the IDE platform device claims 1 byte
too many for its memory resource -- fix the platform code and the IDE driver
in accordance.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver fails to compile with CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA enabled:
drivers/ide/mips/au1xxx-ide.c: In function `auide_build_dmatable':
drivers/ide/mips/au1xxx-ide.c:256: error: implicit declaration of function
`sg_virt'
drivers/ide/mips/au1xxx-ide.c:275: error: implicit declaration of function
`sg_next'
drivers/ide/mips/au1xxx-ide.c:275: warning: assignment makes pointer from
integer without a cast
Fix this by including <linux/scatterlist.h>. While at it, remove the #include's
without which the driver happily builds.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:
include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared
`static' but never defined
include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
`static' but never defined
by wiping out the whole "function prototyping" section from the header file
<asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
already dead in the IDE driver; move the only useful prototype into the driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
