In case bootloader has changed the priority of one/more IRQ lines
Reported-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
switch the args (address, pt_regs) to match with all the other "C"
exception handlers.
This removes the awkwardness in EV_ProtV for page fault vs. unaligned
access.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Line op needs vaddr (indexing) and paddr (tag match). For page sized
flushes (V-P const), each line op will need a different index, but the
tag bits wil remain constant, hence paddr can be setup once outside the
loop.
This improves select LMBench numbers for Aliasing dcache where we have
more "preventive" cache flushing.
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.11-rc7- Linux 3.11.0- 80 4.66 8.88 69.7 112. 268. 8.60 28.0 3489 13.K 27.K # Non alias ARC700
3.11-rc7- Linux 3.11.0- 80 4.64 8.51 68.6 98.5 271. 8.58 28.1 4160 15.K 32.K # Aliasing
3.11-rc7- Linux 3.11.0- 80 4.64 8.51 69.8 99.4 270. 8.73 27.5 3880 15.K 31.K # PTAG loop Inv
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
With Line length being constant now, we can fold the 2 helpers into 1.
This allows applying any optimizations (forthcoming) to single place.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC dcache supports 3 ops - Inv, Flush, Flush-n-Inv.
The programming model however provides 2 commands FLUSH, INV.
INV will either discard or flush-n-discard (based on DT_CTRL bit)
The leaf helper __dc_line_loop() used to take the AUX register
(corresponding to the 2 commands). Now we push that to within the
helper, paving way for code consolidations to follow.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of them is
address calculation via the form &__get_cpu_var(x). This calculates the address for
the instance of the percpu variable of the current processor based on an offset.
Other use cases are for storing and retrieving data from the current processors percpu area.
__get_cpu_var() can be used as an lvalue when writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store and retrieve operations
could use a segment prefix (or global register on other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a percpu area and use
optimized assembly code to read and write per cpu variables.
This patch converts __get_cpu_var into either an explicit address calculation using this_cpu_ptr()
or into a use of this_cpu operations that use the offset. Thereby address calcualtions are avoided
and less registers are used when code is generated.
At the end of the patchset all uses of __get_cpu_var have been removed so the macro is removed too.
The patchset includes passes over all arches as well. Once these operations are used throughout then
specialized macros can be defined in non -x86 arches as well in order to optimize per cpu access by
f.e. using a global register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu variable.
DEFINE_PER_CPU(int, u);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(this_cpu_ptr(&x), y, sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
this_cpu_inc(y)
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
We used to use a percpu structure vq_index to record the cpu to queue
mapping, this is suboptimal since it duplicates the work of XPS and
loses all other XPS functionality such as allowing user to configure
their own transmission steering strategy.
So this patch switches to use XPS and suggest a default mapping when
the number of cpus is equal to the number of queues. With XPS support,
there's no need for keeping per-cpu vq_index and .ndo_select_queue(),
so they were removed also.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now rt6_alloc_cow() is only called by ip6_pol_route() when
rt->rt6i_flags doesn't contain both RTF_NONEXTHOP and RTF_GATEWAY,
and rt->rt6i_flags hasn't been changed in ip6_rt_copy().
So there is no neccessary to judge whether rt->rt6i_flags contains
RTF_GATEWAY or not.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When restoring the PPR value, we incorrectly access the thread structure
at a time where MSR:RI is clear, which means we cannot recover from nested
faults. However the thread structure isn't covered by the "bolted" SLB
entries and thus accessing can fault.
This fixes it by splitting the code so that the PPR value is loaded into
a GPR before MSR:RI is cleared.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We're assigning PE numbers after the completion of PCI probe. During
the PCI probe, we had PE#0 as the super container to encompass all
PCI devices. However, that's inappropriate since PELTM has ascending
order of priority on search on P7IOC. So we need PE#127 takes the
role that PE#0 has previously. For PHB3, we still have PE#0 as the
reserved PE.
The patch supposes that the underly firmware has built the RID to
PE# mapping after resetting IODA tables: all PELTM entries except
last one has invalid mapping on P7IOC, but all RTEs have binding
to PE#0. The reserved PE# is being exported by firmware by device
tree.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need add PE to its own PELTV. Otherwise, the errors originated
from the PE might contribute to other PEs. In the result, we can't
clear up the error successfully even we're checking and clearing
errors during access to PCI config space.
Cc: stable@vger.kernel.org
Reported-by: kalshett@in.ibm.com
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Indirect XSCOM addresses normally have the top bit set (of the 64-bit
address). This doesn't work via the normal debugfs interface, so we use
a different encoding, which we need to convert before calling OPAL.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current debugfs interface to scom is essentially unused
and racy. It uses two different files "address" and "data"
to perform accesses which is at best impractical for anything
but manual use by a developer.
This replaces it with an "access" file which represent the entire
scom address space which can be lseek/read/writen too.
This file only supports accesses that are 8 bytes aligned and
multiple of 8 bytes in size. The offset is logically the SCOM
address multiplied by 8.
Since nothing in userspace exploits that file at the moment, the ABI
change is a no-brainer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On P8, XSCOM addresses has a special "indirect" form that
requires more than 32-bits, so let's use u64 everywhere in
the code instead of u32.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 1e2bd517c1 ("udp6: Fix udp
fragmentation for tunnel traffic.") changed the calculation if
there is enough space to include a fragment header in the skb from a
skb->mac_header dervived one to skb_headroom. Because we already peeled
off the skb to transport_header this is wrong. Change this back to check
if we have enough room before the mac_header.
This fixes a panic Saran Neti reported. He used the tbf scheduler which
skb_gso_segments the skb. The offsets get negative and we panic in memcpy
because the skb was erroneously not expanded at the head.
Reported-by: Saran Neti <Saran.Neti@telus.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cc9d4598 'net: mv643xx_eth: use of_phy_connect if phy_node
present' made the call to phy_scan optional, if the DT has a link to
the phy node.
However phy_scan has the side effect of calling phy_addr_set, which
writes the phy MDIO address to the ethernet controller. If phy_addr_set
is not called, and the bootloader has not set the correct address then
the driver will fail to function.
Tested on Kirkwood.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sockets marked with IP_PMTUDISC_INTERFACE won't do path mtu discovery,
their sockets won't accept and install new path mtu information and they
will always use the interface mtu for outgoing packets. It is guaranteed
that the packet is not fragmented locally. But we won't set the DF-Flag
on the outgoing frames.
Florian Weimer had the idea to use this flag to ensure DNS servers are
never generating outgoing fragments. They may well be fragmented on the
path, but the server never stores or usees path mtu values, which could
well be forged in an attack.
(The root of the problem with path MTU discovery is that there is
no reliable way to authenticate ICMP Fragmentation Needed But DF Set
messages because they are sent from intermediate routers with their
source addresses, and the IMCP payload will not always contain sufficient
information to identify a flow.)
Recent research in the DNS community showed that it is possible to
implement an attack where DNS cache poisoning is feasible by spoofing
fragments. This work was done by Amir Herzberg and Haya Shulman:
<https://sites.google.com/site/hayashulman/files/fragmentation-poisoning.pdf>
This issue was previously discussed among the DNS community, e.g.
<http://www.ietf.org/mail-archive/web/dnsext/current/msg01204.html>,
without leading to fixes.
This patch depends on the patch "ipv4: fix DO and PROBE pmtu mode
regarding local fragmentation with UFO/CORK" for the enforcement of the
non-fragmentable checks. If other users than ip_append_page/data should
use this semantic too, we have to add a new flag to IPCB(skb)->flags to
suppress local fragmentation and check for this in ip_finish_output.
Many thanks to Florian Weimer for the idea and feedback while implementing
this patch.
Cc: David S. Miller <davem@davemloft.net>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
f41f064cf4 ("PCI: Workaround missing pci_set_master in pci drivers") made
pci_enable_bridge() turn on bus mastering if the driver hadn't done so
already. It also added a warning in this case. But there's no reason to
warn about it unless it's actually a problem to enable bus mastering here.
This patch drops the warning because I'm not aware of any such problem.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Paul Bolle <pebolle@tiscali.nl>
Ben Herrenschmidt found that commit 928bea9648 ("PCI: Delay enabling
bridges until they're needed") breaks PCI in some powerpc environments.
The reason is that the PCIe port driver will call pci_enable_device() on
the bridge, so the device is enabled, but skips pci_set_master because
pcie_port_auto and no acpi on powerpc.
Because of that, pci_enable_bridge() later on (called as a result of the
child device driver doing pci_enable_device) will see the bridge as
already enabled and will not call pci_set_master() on it.
Fixed by add checking in pci_enable_bridge, and call pci_set_master
if driver skip that.
That will make the code more robot and wade off problem for missing
pci_set_master in drivers.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bjørn Mork says:
====================
The huawei_cdc_ncm driver.
Enrico has been kind enough to let me repost his driver with the changes
requested by Oliver Neukum during the last review of this series.
The changes I have made from Enricos original v5 series to this version
are:
v6:
- fix to avoid corrupting drvstate->pmcount
- fix error return value from huawei_cdc_ncm_suspend()
- drop redundant testing for subdriver->suspend during resume
- broke a few lines to keep within the 80 columns recommendation
- rebased on top of current net-next
Enrico's orginal introduction to the v5 series follows below. It explains
the background much better than I can.
Bjørn
[quote Enrico Mioso]
So this is a new, revised, edition of the huawei_cdc_ncm.c driver, which
supports devices resembling the NCM standard, but using it also as a mean
to encapsulate other protocols, as is the case for the Huawei E3131 and
E3251 modem devices.
Some precisations are needed however - and I encourage discussion on this: and
that's why I'm sending this message with a broader CC.
Merging those patches might change:
- the way Modem Manager interacts with those devices
- some regressions might be possible if there are some unknown firmware
variants around (Franko?)
First of all: I observed the behaviours of two devices.
Huawei E3131: this device doesn't accept NDIS setup requests unless they're
sent via the embedded AT channel exposed by this driver.
So actually we gain funcionality in this case!
The second case, is the Huawei E3251: which works with standard NCM driver,
still exposing an AT embedded channel. Whith this patch set applied, you gain
some funcionality, loosing the ability to catch standard NCM events for now.
The device will work in both ways with no problems, but this has to be
acknowledged and discussed. Might be we can develop this driver further to
change this, when more devices are tested.
We where thinking Huawei changed their interfaces on new devices - but probably
this driver only works around a nice firmware bug present in E3131, which
prevented the modem from being used in NDIS mode.
I think committing this is definitely wortth-while, since it will allow for
more Huawei devices to be used without serial connection. Some devices like the
E3251 also, reports some status information only via the embedded AT channel,
at least in my case.
Note: I'm not subscribed to any list except the Modem Manager's one, so please
CC me, thanks!!
[/quote]
Enrico Mioso (3):
net: cdc_ncm: Export cdc_ncm_{tx,rx}_fixup functions for re-use
net: huawei_cdc_ncm: Introduce the huawei_cdc_ncm driver
net: cdc_ncm: remove non-standard NCM device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove device IDs of NCM-like (but not NCM-conformant) devices, that are
handled by the huawwei_cdc_ncm driver now.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports devices using the NCM protocol as an encapsulation layer
for other protocols, like the E3131 Huawei 3G modem. This drivers approach was
heavily inspired by the qmi_wwan/cdc_mbim approach & code model.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers implementing NCM-like protocols, may re-use those functions, as is
the case in the huawei_cdc_ncm driver.
Export them via EXPORT_SYMBOL_GPL, in accordance with how other functions have
been exported.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code of flow label in Linux Kernel follows
the rules of RFC 1809 (an informational one) for
conditions on flow label sharing. There rules are
not in the last proposed standard for flow label
(RFC 6437), or in the previous one (RFC 3697).
Since this code does not follow any current or
old standard, we can remove it.
With this removal, the ipv6_opt_cmp function is
now a dead code and it can be removed too.
Changelog to v1:
* add justification for the change
* remove the condition on IPv6 options
[ Remove ipv6_hdr_cmp and it is now unused as well. -DaveM ]
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They convey no information, perhaps I was bitten by some snake at some
point, complete the detox by naming the last of those arguments more
sensibly.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-u1r0dnjoro08dgztiy2g3t2q@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding the check for maximum allowed frequency rate defined in following
file:
/proc/sys/kernel/perf_event_max_sample_rate
When we cross the maximum value we fail and display detailed error
message with advise.
$ perf record -F 3000 ls
Maximum frequency rate (2000) reached.
Please use -F freq option with lower value or consider
tweaking /proc/sys/kernel/perf_event_max_sample_rate.
In case user does not specify the frequency and the default value cross
the maximum, we display warning and set the frequency value to the
current maximum.
$ perf record ls
Lowering default frequency rate to 2000.
Please consider tweaking /proc/sys/kernel/perf_event_max_sample_rate.
Same messages are used for 'perf top'.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1383660887-1734-4-git-send-email-jolsa@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Shorten it, "finding" it is an implementation detail, what callers want
is the pathname, not to ask for it to _always_ do the lookup.
And the existing implementation already caches it, i.e. it doesn't
"finds" it on every call.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-r24wa4bvtccg7mnkessrbbdj@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified. If an ARM
function is registered as a signal handler, and that signal is delivered
inside a block of instructions following an IT instruction, some of the
instructions at the beginning of the signal handler may be skipped if
the IT state bits of the Program Status Register are not cleared by the
kernel.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[catalin.marinas@arm.com: code comment and commit log updated]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Moving sysfs code into generic fs object and preparing it to carry
procfs support.
This should be merged with tools/lib/lk/debugfs.c at some point in the
future.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1383660887-1734-2-git-send-email-jolsa@redhat.com
[ Added fs__ namespace qualifier to some more functions ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently 'perf list' is not very helpful if you forget the syntax:
$ perf list -h
List of pre-defined events (to be used in -e):
After:
$ perf list -h
usage: perf list [hw|sw|cache|tracepoint|pmu|event_glob]
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/527133AD.4030003@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
With a return after the if check an indentation level can be removed.
Indentation shift only; no functional changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1383149707-1008-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch expands the VA_BITS to 42 when the 64K page configuration is
enabled allowing 2TB kernel linear mapping. Linux still uses 2 levels of
page tables in this configuration with pgd now being a full page.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
"HDA Intel MID" is no correct name for Haswell HDMI controllers.
Give them a better name, "HDA Intel HDMI".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI audio controllers seem to get stuck when unaligned buffer
size is used. Let's enable the buffer alignment for the corresponding
entries.
Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the
buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the
necessary AZX_DCAPS bits there.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Entries would be lost if the old tail block was partially filled.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
When pg_init is running no I/O can be submitted to the underlying
devices, as the path priority etc might change. When using queue_io for
this, requests will be piling up within multipath as the block I/O
scheduler just sees a _very fast_ device. All of this queued I/O has to
be resubmitted from within multipathing once pg_init is done.
This approach has the problem that it's virtually impossible to
abort I/O when pg_init is running, and we're adding heavy load
to the devices after pg_init since all of the queued I/O needs to be
resubmitted _before_ any requests can be pulled off of the request queue
and normal operation continues.
This patch will requeue the I/O that triggers the pg_init call, and
return 'busy' when pg_init is in progress. With these changes the block
I/O scheduler will stop submitting I/O during pg_init, resulting in a
quicker path switch and less I/O pressure (and memory consumption) after
pg_init.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[patch header edited for clarity and typos by Mike Snitzer]
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
feature_check needs to be invoked through call, and LDFLAGS may not be
set so quotes are needed.
Thanks to Jiri for spotting the quotes around LDFLAGS; that one was
driving me nuts with the upcoming timerfd feature detection.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1383064996-20933-1-git-send-email-dsahern@gmail.com
[ Fixed conflict with 8a0c4c2843 ("perf tools: Fix libunwind build and feature detection for 32-bit build") ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If the OS does not have timerfd support (e.g., older OS'es like RHEL5)
disable perf kvm stat live.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Jiri Olsa <jolsa@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1383064996-20933-2-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
