The hole reason for __must_check is to not ignore an error.
However, a "ret" value is used at cx25821 just to avoid the
Kernel compilation to compain about it.
That, however, produces another warning (with W=1):
drivers/media/pci/cx25821/cx25821-alsa.c: In function 'cx25821_audio_fini':
drivers/media/pci/cx25821/cx25821-alsa.c:727:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
With the current implementation of driver_for_each_device() and
cx25821_alsa_exit_callback(), there's actually just one
very unlikely condition where it will currently produce
an error: if driver_find() returns NULL.
Ok, there's not much that can be done, as it is on a driver's
function that returns void, but it can at least print some message
if the error happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warning:
drivers/media/pci/cx25821/cx25821-video.c: At top level:
drivers/media/pci/cx25821/cx25821-video.c:766:5: warning: no previous prototype for 'cx25821_vidioc_s_std' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After cx25821-video cleanup, this var is not used anymore:
drivers/media/pci/cx25821/cx25821-video.c: In function 'cx25821_vidioc_try_fmt_vid_cap':
drivers/media/pci/cx25821/cx25821-video.c:591:15: warning: variable 'maxw' set but not used [-Wunused-but-set-variable]
as the code now checks the max width as the default case for the
range check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the driver complains about the pre_detect var:
drivers/media/tuners/r820t.c: In function 'r820t_sysfreq_sel':
drivers/media/tuners/r820t.c:722:31: warning: variable 'pre_dect' set but not used [-Wunused-but-set-variable]
While rtl8232 code comments it, perhaps some other driver may use.
So, the better is to keep the code there, allowing to enable it
via r820t config data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check if the values for c, h and n are within the range is
always true, as, if one of this values is out of range, the
previous "if" clauses will default to a value within the
range.
That fixes the following warning:
drivers/media/dvb-frontends/dib0090.c: In function 'dib0090_set_EFUSE':
drivers/media/dvb-frontends/dib0090.c:1545:5: warning: comparison is always true due to limited range of data type [-Wtype-limits]
and makes the code easier to read.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_wait_lock':
drivers/media/dvb-frontends/dib8000.c:3972:1: warning: 'value' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/dib8000.c:2419:6: note: 'value' was declared here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
isdbt_sb_subchannel is unsigned with 8 bits. So, it will
never be -1. Instead, any value bigger than 13 is invalid.
As is, the current code generates the following warnings:
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_set_isdbt_common_channel':
drivers/media/dvb-frontends/dib8000.c:2358:3: warning: comparison is always true due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_tune':
drivers/media/dvb-frontends/dib8000.c:3107:8: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3153:9: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3160:5: warning: comparison is always false
It should also be noticed that ARIB STD-B31, item
"3.15.6.8 Number of segments" at TMCC table defines the
value 15 for unused segment, and 14 as reserved.
So, better to change the check to consider any value
bigger than 13 to mean that sub-channels should be
disabled, fixing the warning and doing the right thing
even if an invalid value is filled by userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gcc-3.8 correctly found that the variables set by find_freq_tables()
are not initialized if this function is called on something other
than a pxa2xx or pxa3xx:
pxa2xx-cpufreq.c: In function 'pxa_verify_policy':
pxa2xx-cpufreq.c:272:6: warning: 'pxa_freqs_table' may be used uninitialized in this function [-Wmaybe-uninitialized]
pxa2xx-cpufreq.c: In function 'pxa_set_target':
pxa2xx-cpufreq.c:345:23: warning: 'pxa_freq_settings' may be used uninitialized in this function [-Wmaybe-uninitialized]
Rather than adding a bogus initialization that would let us
get a little further before crashing, add an explicit BUG().
We know that this code is designed to run on only these cpus,
so this will fix the build warning and give a more helpful
diagnostic if the code ever changes to run on other machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Kconfig entry for USB_EHCI_MSM unconditionally selects USB_MSM_OTG,
which is now only visible when USB_PHY is also enabled.
This adds an appropriate dependency and enables USB_PHY in the msm
defconfig, avoiding the Kbuild warning:
warning: (USB_EHCI_MSM) selects USB_MSM_OTG which has unmet direct dependencies (USB_SUPPORT && USB_PHY && (USB || USB_GADGET) && ARCH_MSM)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the EHCI driver, OHCI supports a large number of different platform
glue drivers by directly including them, which causes problems with
conflicting macro definitions in some cases. As more ARM architecture
specific back-ends are required to coexist in a single build, we should
split those out into separate drivers. Unfortunately, the infrastructure
for that is still under development, so to give us more time, this uses
a separate *_PLATFORM_DRIVER macro for each ARM specific OHCI backend,
just like we already do on PowerPC and some of the other ARM platforms.
In linux-3.10, only the SPEAr and CNS3xxx back-ends would actually conflict
without this patch, but over time we would get more of them, so this
is a way to avoid having to patch the driver every time it breaks. We
should still split out all back-ends into separate loadable modules,
but that work is only needed to improve code size and cleanliness after
this patch, not for correctness.
While we're here, this fixes the incorrectly sorted error path
for the OMAP1 and OMAP3 backends to ensure we always unregister
the exact set of drivers that were registered before erroring out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig entry for USB_OMAP unconditionally selects USB_ISP1301,
which is now only visible when USB_PHY is also enabled.
This adds an appropriate dependency and enables USB_PHY in the omap1
defconfig, avoiding these build warnings:
warning: (USB_OHCI_HCD && USB_OMAP) selects ISP1301_OMAP which has unmet direct dependencies (USB_SUPPORT && USB_PHY && I2C && ARCH_OMAP_OTG)
Also fix a Makefile typo while we're at it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig entry for USB_LPC32XX unconditionally selects USB_ISP1301,
which is now only visible when USB_PHY is also enabled.
This adds an appropriate dependency and enables USB_PHY in the msm
defconfig, avoiding these build errors:
warning: (USB_LPC32XX) selects USB_ISP1301 which has unmet direct dependencies (USB_SUPPORT && USB_PHY && (USB || USB_GADGET) && I2C)
drivers/built-in.o: In function `usb_hcd_nxp_probe':
drivers/usb/host/ohci-nxp.c:224: undefined reference to `isp1301_get_client'
drivers/built-in.o: In function `lpc32xx_udc_probe':
drivers/usb/gadget/lpc32xx_udc.c:3071: undefined reference to `isp1301_get_client'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if you pass the kernel a dtb where a cpu node has an
unsupported enable-method property (e.g. "not-psci"), it'll explode
horribly, as it iterates over the enable_ops array incorrectly. It
increments the pointer *at* the current element, rather than
incrementing the pointer *to* the current element. As the first two
elements pointed to structures that were contiguous in memory, this
happened to be equivalent. However the third element is NULL, so when
the list is exhausted, smp_get_enable_ops generates the wrong pointer,
and dereferences an arbitrary portion of memory, which currently happens
to contain zero.
This patch fixes this by indirecting the pointer one level, so we
iterate over the array elements correctly, avoiding the below panic:
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
show_pte makes use of the *_none_or_clear_bad style functions. If a
pgd, pud or pmd is identified as being bad, it will then be cleared.
As show_pte appears to be called from either the user or kernel
fault handlers this side effect can lead to unpredictable behaviour;
especially as TLB entries are not invalidated.
This patch removes the page table sanitisation from show_pte. If a
bad pgd, pud or pmd is encountered it is left unmodified.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The compat_stat structure doesn't match the arch/arm/ struct stat
definition. This patch fixes the compat types and struct compat_stat
definition accordingly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The DSB following TLB or cache maintenance ops must be run on the same
CPU. With kernel preemption enabled or for user-space cache maintenance
this may not be the case. This patch adds an explicit DSB in the
__switch_to() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For compiling with allmodconfig, need vga.h file, so generate it which
just only include the asm-generic one.
It is firstly used by drivers/gpu/drm/drm_irq.c.
The related error:
include/video/vga.h:22:21: fatal error: asm/vga.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For systems where the top 32-bits of the MPIDR are all zero, we should
allow the device-tree to specify an #address-size of 0x1 for the CPU reg
property and then zero extend the value there.
Without this patch, kvmtool breaks with the recent mpidr parsing code
introduced in 4c7aa00213 ("arm64: kernel: initialise cpu_logical_map
from the DT").
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
dtv_property_cache is used on several places on very long lines.
On all places it is used, a long list of struct reference is done.
Instead of doing it, at the routines where it is used more than once,
replace it by one temporary var. That may help the compiler to
use a better code. It also makes easier to review the code, as the
lines becomes closer to 80 columns, making them a way clearer
to read.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/r820t.c: In function 'r820t_imr':
drivers/media/tuners/r820t.c:1871:8: warning: 'n_ring' may be used uninitialized in this function [-Wmaybe-uninitialized]
Mauro: This is a FALSE POSITIVE: the loop will always return a value
for n_ring, as the last test will fill it with 15, if the loop fails.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've moved the kfree(fe->tuner_priv) one line earlier, otherwise it is
a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test as written is always false. It looks like the intent was to
test that the bit was not set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
drivers/media/usb/dvb-usb-v2/anysee.c: In function ‘anysee_frontend_attach’:
drivers/media/usb/dvb-usb-v2/anysee.c:641: warning: ‘ret’ may be used uninitialized in this function
And gcc is right (see the ANYSEE_HW_507T case), so initialize ret to zero
to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Memory maps typically require that the buffer size to be page
aligned. Currently, two memops drivers do such alignment
internally, but videobuf-vmalloc doesn't.
Also, the buffer overflow check doesn't take it into account.
So, instead of doing it at each memops driver, enforce it at
VB2 core.
Reported-by: Prabhakar lad <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
In addition to commit 72cc9ba3 "em28xx: ignore isoc DVB USB endpoints with
wMaxPacketSize = 0 bytes for all alt settings" we should not save the endpoint
number of the isoc DVB endpoint before it has been validated.
While the current code works fine, dev->dvb_ep_isoc != 0 could be interpreted
as indicator that the device provides DVB support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf_queue_dma_contig_init_cached() is not used anywhere.
Drop support for it, cleaning up the code a little bit.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While testing v4l2-ctl I noticed that this m2m driver didn't set timestamp_type
and that it spammed the kernel log with debug messages. Set timestamp_type
correctly and add debug module option to enable debug messages.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the sake of simplicity and readability memcpy was replaced with
assignment.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the introduction of the timestamp_type field, it is necessary that
the driver chooses which type it will use. This patch adds support for
the timestamp_type.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add copying of buffer timestamps and set the timestamp_type to
V4L2_BUF_FLAG_TIMESTAMP_COPY to avoid warnings about UNDEFINED
timestamp type like:
WARNING: at drivers/media/v4l2-core/videobuf2-core.c:2042 vb2_queue_init+0xe0/0x18c()
Modules linked in:
[<c0016ef0>] (unwind_backtrace+0x0/0x13c) from [<c0029b3c>] (warn_slowpath_common+0x54/0x64)
[<c0029b3c>] (warn_slowpath_common+0x54/0x64) from [<c0029b68>] (warn_slowpath_null+0x1c/0x24)
[<c0029b68>] (warn_slowpath_null+0x1c/0x24) from [<c03b7018>] (vb2_queue_init+0xe0/0x18c)
[<c03b7018>] (vb2_queue_init+0xe0/0x18c) from [<c03b4e08>] (v4l2_m2m_ctx_init+0xa0/0xc4)
[<c03b4e08>] (v4l2_m2m_ctx_init+0xa0/0xc4) from [<c03ca6c4>] (fimc_m2m_open+0x130/0x1f8)
[<c03ca6c4>] (fimc_m2m_open+0x130/0x1f8) from [<c03a5dd4>] (v4l2_open+0xac/0xe8)
[<c03a5dd4>] (v4l2_open+0xac/0xe8) from [<c0113920>] (chrdev_open+0x9c/0x158)
[<c0113920>] (chrdev_open+0x9c/0x158) from [<c010e488>] (do_dentry_open+0x1f8/0x280)
[<c010e488>] (do_dentry_open+0x1f8/0x280) from [<c010e600>] (finish_open+0x34/0x50)
[<c010e600>] (finish_open+0x34/0x50) from [<c011cc58>] (do_last+0x5bc/0xc00)
[<c011cc58>] (do_last+0x5bc/0xc00) from [<c011d34c>] (path_openat+0xb0/0x484)
[<c011d34c>] (path_openat+0xb0/0x484) from [<c011d824>] (do_filp_open+0x30/0x84)
[<c011d824>] (do_filp_open+0x30/0x84) from [<c010e0f8>] (do_sys_open+0xe8/0x170)
[<c010e0f8>] (do_sys_open+0xe8/0x170) from [<c000f040>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure TRY format is propagated from the sink to source pad.
The format at both pads is always same so the TRY format buffer
for pad 0 is used to hold format for both pads.
While at it remove redundant fmt->pad checking.
Reported-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Originally struct v4l2_capability driver and card name was filled
with name of the platform device. After switching to the device tree
the device names have changed and now are 4 different driver names
reported, depending on the video device opened. So instead of e.g.
"exynos4-fimc" there is now one of: 11800000.fimc, 11810000.fimc,
11820000.fimc, 11830000.fimc.
Fix this by using dev->driver_name, rather than platform device name.
A common vidioc_querycap function is created for both M2M and capture
video node.
This fixes any breakage at user space should any application/library
rely on the driver's name.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure there is no unbalanced pm_runtime_put().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware dependencies (clocks/power domain) the I2C bus
controller needs to be unregistered before fimc-is.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure both debugfs: fimc_is directory and the fw_log file
are properly removed in the driver cleanup sequence.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there is unbalanced module_put() on the s5p-csis module
which prevents it from being unloaded. The subdev's owner module
has reference count decremented in v4l2_device_unregister_subdev()
so just remove this erroneous call.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FIMC-LITE.n subdevs have currently sd->owner field not set,
the exynos-fimc-lite module can be removed at any time, regardless
it is in use by other modules. When this module is unloaded the
kernel can crash easily by accessing video or media device nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing v4l2_device_unregister_subdev() call for the FIMC-IS subdevs
(currently there is only the FIMC-IS-ISP subdev) so corresponding resources
are properly freed upon the media device driver module removal.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyugmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
