A user noticed that there would continue to be 4-6 keypresses even after the
user stopped holding down the button. This was because we were not reading
the bulk pipe faster than the firmware was injecting information, which would
result in a backlog.
Make the query interval faster, and increase the number of cycles before we
start repeating to compensate.
Thanks to Knud Poulsen <knud.poulsen@nokia.com> for pointing this out.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
on 64-bit x86 the physical memory limit is controlled by the sparsemem
bits - which are 44 bits right now. But MAXMEM (the max pfn number
e820 parsing will allow to enter our sizing routines) is set to
0x00003fffffffffff, i.e. 46 bits - that's too large because it overlaps
into the vmalloc range.
So couple MAXMEM to MAX_PHYSMEM_BITS, and add a comment that the
maximum of MAX_PHYSMEM_BITS is 45 bits.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Disable GENERIC_HARDIRQS_NO__DO_IRQ for unconverted platforms.
sh: maple: Do not pass SLAB_POISON to kmem_cache_create()
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/cell/axon-msi: Fix MSI after kexec
powerpc: Fix bootmem reservation on uninitialized node
powerpc: Check for valid hugepage size in hugetlb_get_unmapped_area
Some of the inconsistencies checked for at run time can be detected at
build time already, so duplicate the checks done at run time to also be
done at build time.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Neither of the callers really needs the physical address this function
returns, so eliminate the pointless argument.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: reduce bug table size
This allows reducing the bug table size by half. Perhaps there are
other 64-bit architectures that could also make use of this.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, code robustization
The __swp_...() macros silently relied upon which bits are used for
_PAGE_FILE and _PAGE_PROTNONE. After having changed _PAGE_PROTNONE in
our Xen kernel to no longer overlap _PAGE_PAT, live locks and crashes
were reported that could have been avoided if these macros properly
used the symbolic constants. Since, as pointed out earlier, for Xen
Dom0 support mainline likewise will need to eliminate the conflict
between _PAGE_PAT and _PAGE_PROTNONE, this patch does all the necessary
adjustments, plus it introduces a mechanism to check consistency
between MAX_SWAPFILES_SHIFT and the actual encoding macros.
This also fixes a latent bug in that x86-64 used a 6-bit mask in
__swp_type(), and if MAX_SWAPFILES_SHIFT was increased beyond 5 in (the
seemingly unrelated) linux/swap.h, this would have resulted in a
collision with _PAGE_FILE.
Non-PAE 32-bit code gets similarly adjusted for its pte_to_pgoff() and
pgoff_to_pte() calculations.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: change the reporting of empty BTS records
Correctly report a cleared BTS record as invalid. Used to be reported
as branch from 0 to 0.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Optimistically allocate a DS context. It is extremely unlikely that
one already existed. This simplifies the code a lot.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 80bba1290a removed one necessary
variable initialization. As a result following warning happened:
CC mm/migrate.o
mm/migrate.c: In function 'sys_move_pages':
mm/migrate.c:1001: warning: 'err' may be used uninitialized in this function
More unfortunately, if find_vma() failed, kernel read uninitialized
memory.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
CC: Brice Goglin <Brice.Goglin@inria.fr>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes an inconsistency that became apparent when I
documented the fields of snd_ca0106_details. spi_dac is always
used in a 'boolean' sense, so this cleanup should make no difference.
[Actually, there is one place checking explicitly spi_dac == 1, so
this will change the behavior. But, supposing it's rather a typo,
I apply this clean-up patch -- tiwai]
Signed-off-by: Ben Stanley <Ben.Stanley@exemail.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi wrote an email [1] explaining the fields of snd_ca0106_details,
so I captured the information into the ca0106.h header file.
[1] http://article.gmane.org/gmane.linux.alsa.devel/56783/match=takashi+gpio_type
Signed-off-by: Ben Stanley <Ben.Stanley@exemail.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch export per-cpu CPU cycle usage for a given cpuacct cgroup.
There is a need for a user space monitor daemon to track group CPU
usage on per-cpu base. It is also useful for monitoring CFS load
balancer behavior by tracking per CPU group usage.
Signed-off-by: Ken Chen <kenchen@google.com>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: micro-optimize the code on 64-bit architectures
In the thread regarding to 'export percpu cpuacct cgroup stats'
http://lkml.org/lkml/2008/12/7/13
akpm pointed out that current cpuacct code is inefficient. This patch
refactoring the following:
* make cpu_rq locking only on 32-bit
* change iterator to each_present_cpu instead of each_possible_cpu to
make it hotplug friendly.
It's a bit of code churn, but I was rewarded with 160 byte code size saving
on x86-64 arch and zero code size change on i386.
Signed-off-by: Ken Chen <kenchen@google.com>
Cc: Paul Menage <menage@google.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IDE hpt366 driver doesn't allow DMA for ATAPI devices and MWDMA2 on
ATAPI device locks up pata_hpt366. Follow the suit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_hpt366 is strange in that its two channels occupy two PCI
functions and both are primary channels and bit1 of PCI configuration
register 0x5A indicates cable for both channels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to miscommunication, P/N was mistaken as firmware revision
strings. Update it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When get receiving interface index while no message is received,
the the value seted with setsockopt() should be returned.
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
- For the IPV6_PKTINFO option, it will return an in6_pktinfo
structure with ipi6_addr being in6addr_any and ipi6_ifindex being
zero.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three reasons for me to add this support:
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
2.When no IPV6_PKTINFO ancillary data is received,getsockopt() should
return the sticky option value which set with setsockopt().
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
3.Make the setsockopt implementation POSIX compliant.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.
The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC driver can work with mutliple versions of the FW.
Let the driver load when the embedded FW does not match,
and the FW update mechanism failed.
The iWARP module will make its own loading decision.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enc28j60 driver reads incoming packets in the process (workqueue) context,
not in a tasklet or the interrupt context. Thus, we should use netif_rx_ni()
to deliver those packets to the networking layer, instead of netif_rx(). This
way incoming packets don't wait in the incoming queue for the next IRQ to be
serviced.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TLAN chip does not support tranmissions smaller than 64
bytes. Smaller transfers need to be padded up to that size. This was
broken by commit id 41873e9aff ("tlan:
get rid of padding buffer").
<URL:http://bugzilla.kernel.org/show_bug.cgi?id=11754>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pppol2tp driver has had broken UDP checksum code for a long
time. This patch fixes it. If UDP checksums are enabled in the
tunnel's UDP socket, the L2TP driver now properly validates the
checksum on receive and fills in the checksum on transmit. If the
network device has hardware checksum support and is enabled, it is
used instead of generating/checking the checksum in software.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an inconsistency in nfnetlink_conntrack.h that
I introduced myself. The problem is that CTA_NAT_SEQ_UNSPEC is
missing from enum ctattr_natseq. This inconsistency may lead to
problems in the message parsing in userspace (if the message
contains the CTA_NAT_SEQ_* attributes, of course).
This patch breaks backward compatibility, however, the only known
client of this code is libnetfilter_conntrack which indeed crashes
because it assumes the existence of CTA_NAT_SEQ_UNSPEC to do
the parsing.
The CTA_NAT_SEQ_* attributes were introduced in 2.6.25.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings by making the functions static:
drivers/isdn/hardware/eicon/di.c:356:6: warning: symbol 'isdn_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/di.c:558:6: warning: symbol 'isdn_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:595:6: warning: symbol 'api_parse' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:634:6: warning: symbol 'api_save_msg' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:666:6: warning: symbol 'api_load_msg' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:3417:6: warning: symbol 'manufacturer_req' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:3745:6: warning: symbol 'manufacturer_res' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4077:6: warning: symbol 'control_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4743:6: warning: symbol 'data_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4779:6: warning: symbol 'data_ack' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4805:6: warning: symbol 'sig_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6173:6: warning: symbol 'SendInfo' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6349:6: warning: symbol 'SendMultiIE' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6468:6: warning: symbol 'nl_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7250:6: warning: symbol 'get_plci' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7409:6: warning: symbol 'add_d' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7427:6: warning: symbol 'add_ai' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7448:6: warning: symbol 'add_b1' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7912:6: warning: symbol 'add_b23' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8709:6: warning: symbol 'nl_req_ncci' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8731:6: warning: symbol 'send_req' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8866:6: warning: symbol 'listen_check' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8909:6: warning: symbol 'IndParse' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8994:6: warning: symbol 'ie_compare' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9003:6: warning: symbol 'find_cip' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9071:6: warning: symbol 'SetVoiceChannel' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9089:6: warning: symbol 'VoiceChannelOff' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9102:6: warning: symbol 'AdvCodecSupport' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9198:6: warning: symbol 'CodecIdCheck' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: micro-optimization
Is there any reason why x86 rdtscll have to use the out of line
function instead of inline __native_read_tsc()? native_read_tsc and
__native_read_tsc is essentially the same functions.
Patch to let x86 rdtscll() to use the inline version of read_tsc.
Signed-off-by: Ken Chen <kenchen@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement NIC Tx multiqueue.
Bump up driver version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: micro-optimization
Skip the hard work when there is none.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: sharpen the wakeup-granularity to always be against current scheduler time
It was possible to do the preemption check against an old time stamp.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds GRO support to e1000e by making it invoke napi_gro_receive
instead of netif_receive_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ethtool ops to enable and disable GRO. It also
makes GRO depend on RX checksum offload much the same as how TSO
depends on SG support.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the TCP-specific portion of GRO. The criterion for
merging is extremely strict (the TCP header must match exactly apart
from the checksum) so as to allow refragmentation. Otherwise this
is pretty much identical to LRO, except that we support the merging
of ECN packets.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Presently limited to Cayman, Dreamcast, Microdev, and SystemH 7751.
Re-enable it for everyone once these have been fixed up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the helper skb_gro_receive to merge packets for
GRO. The current method is to allocate a new header skb and then
chain the original packets to its frag_list. This is done to
make it easier to integrate into the existing GSO framework.
In future as GSO is moved into the drivers, we can undo this and
simply chain the original packets together.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support for IPv4.
The criteria for merging is more stringent than LRO, in particular,
we require all fields in the IP header to be identical except for
the length, ID and checksum. In addition, the ID must form an
arithmetic sequence with a difference of one.
The ID requirement might seem overly strict, however, most hardware
TSO solutions already obey this rule. Linux itself also obeys this
whether GSO is in use or not.
In future we could relax this rule by storing the IDs (or rather
making sure that we don't drop them when pulling the aggregate
skb's tail).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
