This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bug report from: wenxiong@linux.vnet.ibm.com
The issue is happened in dual controller configuration. We got the
sysfs warnings when rmmod the ipr module.
enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister()
for each componment deivce, device_unregister() ->device_del()->kobject_del()
->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL.
For each componment device,
enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link()
in which checking kobj->sd again, it has been set as NULL when doing
device_unregister. So we saw all these sysfs WARNING.
Tested-by: wenxiong@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When multiple vectors are used, the vector variable is over written,
resulting in unhandled operation for those vectors.
This fix prevents the problem by maitaining HBA instance and
vector values for each irq.
[jejb: checkpatch fixes]
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting the phy state for hard reset response.
After sending hard reset for a device ,phy down event sets
the phy state to zero but for phy up event it will not set
the phy state again.This will cause problem to successive
hard resets.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of direct attached SATA device delay is not enough.
It will give crash for set device state command response and
wait_for_completion is the best solution for this.
Signed-off-by: Nikith.Ganigarakoppal@pmcs.com
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
Pull scheduler fixes from Ingo Molnar:
"Various smaller fixlets, all over the place"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Fix generation of device-drivers
sched: Expose preempt_schedule_irq()
sched: Fix a trivial typo in comments
sched: Remove unused variable in 'struct sched_domain'
sched: Avoid NULL dereference on sd_busy
sched: Check sched_domain before computing group power
MAINTAINERS: Update file patterns in the lockdep and scheduler entries
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSnJuAAAoJEFjIrFwIi8fJj7sIAJQgSEMWJcEOBJ3lujfbhhKr
9GYfyNILfBjaOcH3LkA354U0JB3y4vON/xz6ONzMO4X7Jj6oUzACeEluq2iexlji
VDxqtnDJGS/82TcIN5xOVKRZbIqZ0xdRjK2f4h7AU9lIoIk+SJEJIycG1RGqqrmr
0nv39lUMjQhXNDhUjyt7e6JQj5GHrP0hzp5ngEQGcquPKbHXUInlwkB/kCH3zwju
2kEYQyKSWFoZCVtIBDeHplcZw9r/zWyOHBxjWOVoI/KZk8k+6d2breC3hv0lrhvU
qkJwzJcKZGlFdiCVHLbo3sTHf0NvvfF+qBCv7JbsymYaQc5SkrATmQ/DAUOssg0=
=emSu
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"Fixes to patches that went in this merge window along with a latent
bug:
- Fix lazy flushing in case m2p override fails.
- Fix module compile issues with ARM/Xen
- Add missing call to DMA map page for Xen SWIOTLB for ARM"
* tag 'stable/for-linus-3.13-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gnttab: leave lazy MMU mode in the case of a m2p override failure
xen/arm: p2m_init and p2m_lock should be static
arm/xen: Export phys_to_mach to fix Xen module link errors
swiotlb-xen: add missing xen_dma_map_page call
Building brcmfmac for sparc64 gave the following warning:
CC [M] drivers/net/wireless/brcm80211/brcmfmac/bcmsdh_sdmmc.o
bcmsdh_sdmmc.c: In function 'brcmf_sdioh_request_byte':
bcmsdh_sdmmc.c:89:6: warning: 'err_ret' may be used uninitialized
in this function [-Wuninitialized]
Inspecting the code it indeed had a path of execution in
which the return value was used uninitialized. This patch
fixes that code path.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kmalloc fails wcn36xx_smd_rsp_process will attempt to dereference
a NULL pointer. There might be a better error recovery then just
printing an error, but printing an error message is better then the
current behaviour.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code in ath9k_hw_set_clockrate function indicates that ah->curchan
(and thus chan local variable) may be NULL. If that is indeed the
case, IS_CHAN_HT40(chan) check has to be performed only in branch
where chan is not NULL. Moving the code under already existing
if condition fixes this issue.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM parameter to determine whether the bias
strength values for XLNA have to be applied is part
of the miscConfiguration field and not featureEnable.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 5 in the miscConfiguration field of the base EEPROM
header denotes whether QuickDrop is enabled or not. Fix
the incorrect usage of BIT(1) and also make sure that
this is done only for the required chips.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A smattering of driver specific fixes here, including a bunch for a
long standing common pattern in the error handling paths, and a fix for
an embarrassing thinko in the new devm master registration code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=DNnX
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A smattering of driver specific fixes here, including a bunch for a
long standing common pattern in the error handling paths, and a fix
for an embarrassing thinko in the new devm master registration code"
* tag 'spi-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi/pxa2xx: Restore private register bits.
spi/qspi: Fix qspi remove path.
spi/qspi: cleanup pm_runtime error check.
spi/qspi: set correct platform drvdata in ti_qspi_probe()
spi/pxa2xx: add new ACPI IDs
spi: core: invert success test in devm_spi_register_master
spi: spi-mxs: fix reference leak to master in mxs_spi_remove()
spi: bcm63xx: fix reference leak to master in bcm63xx_spi_remove()
spi: txx9: fix reference leak to master in txx9spi_remove()
spi: mpc512x: fix reference leak to master in mpc512x_psc_spi_do_remove()
spi: rspi: use platform drvdata correctly in rspi_remove()
spi: bcm2835: fix reference leak to master in bcm2835_spi_remove()
Pull networking updates from David Miller:
"Here is a pile of bug fixes that accumulated while I was in Europe"
1) In fixing kernel leaks to userspace during copying of socket
addresses, we broke a case that used to work, namely the user
providing a buffer larger than the in-kernel generic socket address
structure. This broke Ruby amongst other things. Fix from Dan
Carpenter.
2) Fix regression added by byte queue limit support in 8139cp driver,
from Yang Yingliang.
3) The addition of MSG_SENDPAGE_NOTLAST buggered up a few sendpage
implementations, they should just treat it the same as MSG_MORE.
Fix from Richard Weinberger and Shawn Landden.
4) Handle icmpv4 errors received on ipv6 SIT tunnels correctly, from
Oussama Ghorbel. In particular we should send an ICMPv6 unreachable
in such situations.
5) Fix some regressions in the recent genetlink fixes, in particular
get the pmcraid driver to use the new safer interfaces correctly.
From Johannes Berg.
6) macvtap was converted to use a per-cpu set of statistics, but some
code was still bumping tx_dropped elsewhere. From Jason Wang.
7) Fix build failure of xen-netback due to missing include on some
architectures, from Andy Whitecroft.
8) macvtap double counts received packets in statistics, fix from Vlad
Yasevich.
9) Fix various cases of using *_STATS_BH() when *_STATS() is more
appropriate. From Eric Dumazet and Hannes Frederic Sowa.
10) Pktgen ipsec mode doesn't update the ipv4 header length and checksum
properly after encapsulation. Fix from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
net/mlx4_en: Remove selftest TX queues empty condition
{pktgen, xfrm} Update IPv4 header total len and checksum after tranformation
virtio_net: make all RX paths handle erors consistently
virtio_net: fix error handling for mergeable buffers
virtio_net: Fixed a trivial typo (fitler --> filter)
netem: fix gemodel loss generator
netem: fix loss 4 state model
netem: missing break in ge loss generator
net/hsr: Support iproute print_opt ('ip -details ...')
net/hsr: Very small fix of comment style.
MAINTAINERS: Added net/hsr/ maintainer
ipv6: fix possible seqlock deadlock in ip6_finish_output2
ixgbe: Make ixgbe_identify_qsfp_module_generic static
ixgbe: turn NETIF_F_HW_L2FW_DOFFLOAD off by default
ixgbe: ixgbe_fwd_ring_down needs to be static
e1000: fix possible reset_task running after adapter down
e1000: fix lockdep warning in e1000_reset_task
e1000: prevent oops when adapter is being closed and reset simultaneously
igb: Fixed Wake On LAN support
inet: fix possible seqlock deadlocks
...
Simple fix to set the correct current limit for SD0/1/6.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes: bc407334e9 (regulator: as3722: add regulator driver for AMS AS3722)
Cc: stable@vger.kernel.org
The pipe code was trying (and failing) to be very careful about freeing
the pipe info only after the last access, with a pattern like:
spin_lock(&inode->i_lock);
if (!--pipe->files) {
inode->i_pipe = NULL;
kill = 1;
}
spin_unlock(&inode->i_lock);
__pipe_unlock(pipe);
if (kill)
free_pipe_info(pipe);
where the final freeing is done last.
HOWEVER. The above is actually broken, because while the freeing is
done at the end, if we have two racing processes releasing the pipe
inode info, the one that *doesn't* free it will decrement the ->files
count, and unlock the inode i_lock, but then still use the
"pipe_inode_info" afterwards when it does the "__pipe_unlock(pipe)".
This is *very* hard to trigger in practice, since the race window is
very small, and adding debug options seems to just hide it by slowing
things down.
Simon originally reported this way back in July as an Oops in
kmem_cache_allocate due to a single bit corruption (due to the final
"spin_unlock(pipe->mutex.wait_lock)" incrementing a field in a different
allocation that had re-used the free'd pipe-info), it's taken this long
to figure out.
Since the 'pipe->files' accesses aren't even protected by the pipe lock
(we very much use the inode lock for that), the simple solution is to
just drop the pipe lock early. And since there were two users of this
pattern, create a helper function for it.
Introduced commit ba5bb14733 ("pipe: take allocation and freeing of
pipe_inode_info out of ->i_mutex").
Reported-by: Simon Kirby <sim@hostway.ca>
Reported-by: Ian Applegate <ia@cloudflare.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # v3.10+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With git commit 79c74ecbeb
"s390/time,vdso: convert to the new update_vsyscall interface"
the new update_vsyscall function already does the sum of xtime
and wall_to_monotonic. The old update_vsyscall function only
copied the wall_to_monotonic offset. The vdso code needs to be
modified to take this into consideration.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Binary was written as binay, probably by mistake. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It seems that AD1986A cannot manage the dynamic pin on/off for
auto-muting, but rather gets confused. Since each output has own amp,
let's use it instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Cc: <stable@vger.kernel.org> [v3.11+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ad_vmaster_eapd_hook() needs to handle the inverted EAPD case
properly, too. Otherwise the output gets broken on Lenovo N100 with
AD1986A codec.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64971
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code to use the ECTG instruction to calculate the cputime for the
current thread is currently used only for the per-thread CPU-clock
with the clockid -2 (PID=0, VIRT=1). Use the same code for the clockid
CLOCK_THREAD_CPUTIME_ID to speed up the more common clockid as well.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The access-list entry is supposed to have the fetch-only bit set, however
a reserved bit got set instead.
Userspace isn't able to write to the page anyway since the accessed page
has the read-only bit set. So this saves us only for bad surprises in the
future if the reserved bit gets used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In current models, maximum number of active cores is 101.
[heiko.carstens@de.ibm.com]: Xose's patch increased the maximum possible
value of CONFIG_NR_CPUS to 101. I changed this to 256 instead.
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
struct sclp_cpu_info contains entries only for 255 cpus, while the new
smp fallback sigp detection code will fill up to 256 entries.
Even though there is no machine available which has 256 cpus and where
in addition the fallback sigp cpu detection code will be used we better
fix this, to prevent out of bound accesses.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit "s390/sclp: Consolidate early sclp init calls to sclp_early_detect()"
(7b50da53f6) replaced the sclp_event_mask_early()
with sclp_set_event_mask(). The early_event_mask_sccb variable is no longer
initialized but is still used in sclp_has_linemode() and sclp_has_vt220().
Replace early_event_mask_sccb with the sccb_early variable in both
functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After the call to del_gendisk, the gendisk still holds a reference to
its request_queue. We must not modify the gendisks queue pointer
before the put_disk call, or the gendisk_release function cannot
release the reference and the memory for the request_queue structure
is lost.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ASUS Z35HL laptop also needs the very same fix as the previous one
that was applied to ASUS W7J.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66231
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The change to support Genius Manticore Keyboard also changed behaviour
for Genius Gx Imperator Keyboard, as there is no break between the
cases. This is presumably a mistake.
Reported by Coverity as CID 1134029.
Fixes: 4a2c94c9b6 ('HID: kye: Add report fixup for Genius Manticore Keyboard')
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The static checker found a possible array overflow in atmel/abdac.c:
static checker warning: "sound/atmel/abdac.c:373 set_sample_rates()
error: buffer overflow 'dac->rates' 6 <= 6"
This patch papers over the buggy point, by ensuring that dac->rates[]
update not overflowing the actual array size.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In doc, it said that 'Currently supported controllers - "memory"',
but actually we can use cgroup_disable=cpu,cpuset and all other
controllers, so this is confusing for cgroup users without much
cgroup knowledge. We need to make it clear.
[some comments copied from Paul Menage's original patch 8bab8dded]
Signed-off-by: Qiang Huang <h.huangqiang@huawei.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch resolves a dead lock issue that could be incurred when
exynos_drm_crtc_dpms function was called.
The exynos_drm_crtc_dpms function waits for the completion of pended
page flip events. However, preclose callback - this releases all unhandled
page flip events - is called prior to the exynos_drm_crtc_dpms function call
when drm is closed. So at this time, this will make the exynos_drm_crtc_dpms
to wait infiniately for the completion of the page flip events.
This patch releases the unhandled page flip events at postclose instead
of preclose so that exynos_drm_crtc_dpms function can be waked up.
Changelog v2:
- fix a memory leak when drm is closed.
. it has a memory leak when a requeste page flip is handled after
drm_events_release() is called and before drm_fb_release()
is called. At this time, a drm_pending_event will not be freed.
So also this chage releases the drm_pending_event at postclose().
And it calls drm_vblank_put() for pair if there is any unhandled page
flip event.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Mauro add "*.png" and "*.gif" in DocBook/.gitignore in commit 6d172492,
but forgot to add "*.svg", this made git unnecessary to track directory
DocBook/media_api generated by `make htmldocs`:
$ git status
# On branch master
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# Documentation/DocBook/media_api/
nothing added to commit but untracked files present (use "git add" to track)
Add "*.svg" to DocBook/.gitignore so git will not track directory
DocBook/media_api, since there is no file in that directory it interest in.
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix some typos in three documentations.
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removed obsolte parameters from boot-options.txt.
Verified by grepping around in arch/x86/.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
documentation: Add links to TRACE_EVENT documentation
Existing tracepoint documentation doesn't mention the popular
TRACE_EVENT
macro. Since an excellent series of articles on proper usage already
exists, respective links are added to the existing documentation.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Two concurrent calls to cmd_db2man may attempt to compress manual
pages generated by each other. gzip can then fail due to an input
file having already been compressed and removed.
Move the gzip command to the top-level mandocs target.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Bastian Blank <waldi@debian.org>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Trying to generate xhtml causes all functions to show up with a prefix
of "fsfunc" in the output, so just back off to html until someone
fixes the toolchain.
Note that this is not a problem with kernel-doc, it's an issue with
however "xmlto" renders xhtml output.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
