This follows on the patch to allocate LCLA dynamically: the
on-chip memory is needed for other things so now that that
we're using it dynamically we can remove the LCLA resource
altogether and free up some ESRAM memory.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ARMv6 and above have a restriction whereby aliasing virtual:physical
mappings must not have differing memory type and sharability
attributes. Strictly, this covers the memory type (strongly ordered,
device, memory), cache attributes (uncached, write combine, write
through, write back read alloc, write back write alloc) and the
shared bit.
However, using ioremap() and its variants on system RAM results in
mappings which differ in these attributes from the main system RAM
mapping. Other architectures which similar restrictions approch this
problem in the same way - they do not permit ioremap on main system
RAM.
Make ARM behave in the same way, with a WARN_ON() such that users can
be traced and an alternative approach found.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added support for tnetv107x evaluation module.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for the tnetv107x gpio controller.
Key differences between davinci and tnetv107x controllers:
- register map - davinci's controller is organized into banks of 32 gpios,
tnetv107x has a single space with arrays of registers for in, out,
direction, etc.
- davinci's controller has separate set/clear registers for output, tnetv107x
has a single direct mapped register.
This patch does not yet add gpio irq support on this controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
TNETV107X is a Texas Instruments SOC that shares a number of common features
with the Davinci architecture. Some of the key differences between
traditional Davincis and this new SOC are as follow:
1. The SOCs clock architecture includes a new spread-spectrum PLL. Some
elements of the clock architecture are reused from Davinci (e.g. LPSC), but
the PLL related code is overridden using existing interfaces in "struct clk".
2. The MMR layout on this SOC is substantially different from Davinci.
Consequently, the fixed I/O map is a whole lot more convoluted (more so than
DA8xx). The net impact here is that IO_ADDRESS() will not work on this SoC,
and therefore all mappings have to be through ioremap().
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Added definitions for tnetv107x uart base addresses, and modified base address
selection for kernel decompressor to check for tnetv107x machine type.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adopts a debug uart selection similar to the OMAP model. During
the boot process, the uncompress code determines the physical and virtual base
addresses of the board-specific debug uart. These addresses are then passed
on to the in-kernel debug macros through a small chunk of memory placed just
below the page tables (@0x80003ff8).
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch registers the WM8750 codec on a proper place on the ZipitZ2
machine after the WM8750 driver was converted to new API.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the AER915 battery chip into Zipit Z2
platform file.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Use the resume callback of the pda_power supply framework to check for a
'charge finished' event that might have occured during the sleep phase.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is support for custom design based on Toradex Colibri PXA270 CPU card.
Initial patch was by Pavel Revak.
[daniel - rebased the code to follow the module/board split]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Pavel Revak <palo@bielyvlk.sk>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Follow the idea of several MX31 based boards and split code that is
related to the module from code that is baseboard specific. This makes
adding new base board support easier, while avoiding code duplication.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch just moves code around and polishes it. Also, compile in only
selected pieces of hardware.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the MAX1587A used on Voipac PXA270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds a driver for a harddrive attached to PXA address and data bus.
Unlike pata_platform, this driver allows usage of PXA DMA controller, making the
transmission speed 3x higher.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds the interrupt layer onto the initial trout gpio
changes.
There changes were adapted from the Google driver which lists
Arve Hjønnevåg <arve@android.com> as the author.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This adds missing registers to the list of corrupted registers and
removes a wrong comment about r9 on entry
While at it the formatting of the comment to cache_off is changed to
resemble the other two.
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Probably the register content for cache operations is "don't care" in
practice, but as r1 is explicitly zeroed, use that one.
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
__armv3_mpu_cache_on seems broken. As there is noone around who knows
about these machines just keep the code as is but point out the strange
things.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is the basic support for at91sam9g46, at91sam9m10 and at91sam9m11. Those
are just very basic cpu macros and clock definition.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ep93xx core helper function ep93xx_devcfg_set_clear should mask the
clear_bits before setting the new set_bits in case the clear_bits are a
mask value that also includes the set_bits.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a core.c __init function to handle the physmap flash
registration for all the ep93xx platforms. Also, modify all
the ep93xx platforms to use this new function.
This simplifies all the ep93xx platform init code and reduces
the size of the kernel when including multiple ep93xx boards.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Martin Guy <martinwguy@gmail.com>
Acked-by: Hubert Feurstein <hubert.feurstein@contec.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the platform registration for the ep93xx backlight driver that
is now merged.
Since the pwm BRIGHT signal only functions if the video system is
operating, register the backlight when the framebuffer device is
registered.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add pin config macros for the pins on the DB8500.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the newly added infrastructure to configure the SSP0 and I2C[0-3]
pins on the MOP500 board.
The u8500_init_devices() call needed to be moved up in order to register
the GPIO device first.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This removes the hard-coded shift values for the MTU timer, since
the different platforms using this has very different running
frequencies doing this dynamically is a better idea. Also take
this opportunity to make a more through shutdown of the MTU
clockevent when requested.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/plat-nomadik/gpio.c: In function 'nmk_gpio_remove':
arch/arm/plat-nomadik/gpio.c:630: warning: ignoring return value of 'gpiochip_remove', declared with attribute warn_unused_result
Because this function is marked __exit and this code can't be built as a
module, this function is never used. So just remove it, fixing the
warning in the process.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
So that gpio_to_irq() works.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
So that set_irq_wake() works.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the platform driver registration to a core_initcall, instead of an
arch_initcall. This will allow us to use gpio related calls in
init_machine() (which is an arch_initcall) after adding the gpio
platform devices.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a pin configuration API to all pin-related configuration to be
specified with a single macro and groups of pins to be configured
at one go. Based on the PXA MFP implementation.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Extract out a portion of nmk_gpio_set_mode() that can be called with the
lock already held. This will be used from the pincfg API.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ->direction_output() callback needs to set the value it was passed,
in addition to setting the direction as output. On this peripheral, we
can't set the value before setting the direction, so set it after.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement set_type() to allow configuration of the trigger type.
Cc: Abhijeet Dharmapurikar <adharmap@quicinc.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
