The hardware semaphore covers the configuration register as well as the
ICB registers. The ICB high and low regs contain the address of the
initialization control block and the config register is used to signal
the hardware that a block is ready to be downloaded. Currently we were
only protecting the ICB regs. This changes expands to cover the config
register as well.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a bug in addrconf_prefix_rcv() where it won't update the
preferred lifetime of an IPv6 address if the current valid lifetime
of the address is less than 2 hours (the minimum value in the RA).
For example, If I send a router advertisement with a prefix that
has valid lifetime = preferred lifetime = 2 hours we'll build
this address:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
valid_lft 7175sec preferred_lft 7175sec
If I then send the same prefix with valid lifetime = preferred
lifetime = 0 it will be ignored since the minimum valid lifetime
is 2 hours:
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:217:8ff:fe7d:4718/64 scope global dynamic
valid_lft 7161sec preferred_lft 7161sec
But according to RFC 4862 we should always reset the preferred lifetime
even if the valid lifetime is invalid, which would cause the address
to immediately get deprecated. So with this patch we'd see this:
5: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2001:1890:1109:a20:21f:29ff:fe5a:ef04/64 scope global deprecated dynamic
valid_lft 7163sec preferred_lft 0sec
The comment winds-up being 5x the size of the code to fix the problem.
Update the preferred lifetime of IPv6 addresses derived from a prefix
info option in a router advertisement even if the valid lifetime in
the option is invalid, as specified in RFC 4862 Section 5.5.3e. Fixes
an issue where an address will not immediately become deprecated.
Reported by Jens Rosenboom.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP pushed the skb above the sctp chunk header, so the
check of pskb_may_pull(skb, nh + offset + 1 - skb->data) in
_decode_session6() will never return 0 and the ports decode
of sctp will always fail. (nh + offset + 1 - skb->data < 0)
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP pushed the skb data above the sctp chunk header, so the check
of pskb_may_pull(skb, xprth + 4 - skb->data) in _decode_session4() will
never return 0 because xprth + 4 - skb->data < 0, the ports decode of
sctp will always fail.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Large page first chunk allocator is primarily used for NUMA machines;
however, its NUMA handling is extremely simplistic. Regardless of
their proximity, each cpu is put into separate large page just to
return most of the allocated space back wasting large amount of
vmalloc space and increasing cache footprint.
This patch teachs NUMA details to large page allocator. Given
processor proximity information, pcpu_lpage_build_unit_map() will find
fitting cpu -> unit mapping in which cpus in LOCAL_DISTANCE share the
same large page and not too much virtual address space is wasted.
This greatly reduces the unit and thus chunk size and wastes much less
address space for the first chunk. For example, on 4/4 NUMA machine,
the original code occupied 16MB of virtual space for the first chunk
while the new code only uses 4MB - one 2MB page for each node.
[ Impact: much better space efficiency on NUMA machines ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: David Miller <davem@davemloft.net>
Currently cpu and unit are always identity mapped. To allow more
efficient large page support on NUMA and lazy allocation for possible
but offline cpus, cpu -> unit mapping needs to be non-linear and/or
sparse. This can be easily implemented by adding a cpu -> unit
mapping array and using it whenever looking up the matching unit for a
cpu.
The only unusal conversion is in pcpu_chunk_addr_search(). The passed
in address is unit0 based and unit0 might not be in use so it needs to
be converted to address of an in-use unit. This is easily done by
adding the unit offset for the current processor.
[ Impact: allows non-linear/sparse cpu -> unit mapping, no visible change yet ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
percpu core doesn't need to tack all the allocated pages. It needs to
know whether certain pages are populated and a way to reverse map
address to page when freeing. This patch drops pcpu_chunk->page[] and
use populated bitmap and vmalloc_to_page() lookup instead. Using
vmalloc_to_page() exclusively is also possible but complicates first
chunk handling, inflates cache footprint and prevents non-standard
memory allocation for percpu memory.
pcpu_chunk->page[] was used to track each page's allocation and
allowed asymmetric population which happens during failure path;
however, with single bitmap for all units, this is no longer possible.
Bite the bullet and rewrite (de)populate functions so that things are
done in clearly separated steps such that asymmetric population
doesn't happen. This makes the (de)population process much more
modular and will also ease implementing non-standard memory usage in
the future (e.g. large pages).
This makes @get_page_fn parameter to pcpu_setup_first_chunk()
unnecessary. The parameter is dropped and all first chunk helpers are
updated accordingly. Please note that despite the volume most changes
to first chunk helpers are symbol renames for variables which don't
need to be referenced outside of the helper anymore.
This change reduces memory usage and cache footprint of pcpu_chunk.
Now only #unit_pages bits are necessary per chunk.
[ Impact: reduced memory usage and cache footprint for bookkeeping ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
(de)populate functions are about to be reimplemented to drop
pcpu_chunk->page array. Move a few functions so that the rewrite
patch doesn't have code movement making it more difficult to read.
[ Impact: code movement ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Now that all first chunk allocator helpers allocate and map the first
chunk themselves, there's no need to have optional default alloc/map
in pcpu_setup_first_chunk(). Drop @populate_pte_fn and only leave
@dyn_size optional and make all other params mandatory.
This makes it much easier to follow what pcpu_setup_first_chunk() is
doing and what actual differences tweaking each parameter results in.
[ Impact: drop unused code path ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Generalize and move x86 setup_pcpu_lpage() into
pcpu_lpage_first_chunk(). setup_pcpu_lpage() now is a simple wrapper
around the generalized version. Other than taking size parameters and
using arch supplied callbacks to allocate/free/map memory,
pcpu_lpage_first_chunk() is identical to the original implementation.
This simplifies arch code and will help converting more archs to
dynamic percpu allocator.
While at it, factor out pcpu_calc_fc_sizes() which is common to
pcpu_embed_first_chunk() and pcpu_lpage_first_chunk().
[ Impact: code reorganization and generalization ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
At first, percpu first chunk was always setup page-by-page by the
generic code. To add other allocators, different parts of the generic
initialization was made optional. Now we have three allocators -
embed, remap and 4k. embed and remap fully handle allocation and
mapping of the first chunk while 4k still depends on generic code for
those. This makes the generic alloc/map paths specifci to 4k and
makes the code unnecessary complicated with optional generic
behaviors.
This patch makes the 4k allocator to allocate and map memory directly
instead of depending on the generic code. The only outside visible
change is that now dynamic area in the first chunk is allocated
up-front instead of on-demand. This doesn't make any meaningful
difference as the area is minimal (usually less than a page, just
enough to fill the alignment) on 4k allocator. Plus, dynamic area in
the first chunk usually gets fully used anyway.
This will allow simplification of pcpu_setpu_first_chunk() and removal
of chunk->page array.
[ Impact: no outside visible change other than up-front allocation of dyn area ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Generalize and move x86 setup_pcpu_4k() into pcpu_4k_first_chunk().
setup_pcpu_4k() now is a simple wrapper around the generalized
version. Other than taking size parameters and using arch supplied
callbacks to allocate/free memory, pcpu_4k_first_chunk() is identical
to the original implementation.
This simplifies arch code and will help converting more archs to
dynamic percpu allocator.
While at it, s/pcpu_populate_pte_fn_t/pcpu_fc_populate_pte_fn_t/ for
consistency.
[ Impact: code reorganization and generalization ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
The only extra feature @unit_size provides is making dead space at the
end of the first chunk which doesn't have any valid usecase. Drop the
parameter. This will increase consistency with generalized 4k
allocator.
James Bottomley spotted missing conversion for the default
setup_per_cpu_areas() which caused build breakage on all arcsh which
use it.
[ Impact: drop unused code path ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
The @addr passed into pcpu_chunk_addr_search() is unit0 based address
and thus should be matched inside unit0 area. Currently, when it uses
chunk size when determining whether the address falls in the first
chunk. Addresses in unitN where N>0 shouldn't be passed in anyway, so
this doesn't cause any malfunction but fix it for consistency.
[ Impact: mostly cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
* fix/hda:
ALSA: hda - Add sanity check in PCM open callback
ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
ALSA: hda - Avoid invalid formats and rates with shared SPDIF
ALSA: hda - Improve ASUS eeePC 1000 mixer
ALSA: hda - Add GPIO1 control at muting with HP laptops
Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver. This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max. So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing. If any of them can be zero, disable
the SPDIF sharing mode instead. Otherwise it will lead to a PCM
configuration error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus noticed that the variable name 'old_val' is
confusingly named in these functions - the correct
naming is 'new_val'.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
LKML-Reference: <alpine.LFD.2.01.0907030942260.3210@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Block layer used to merge requests and bios with different failfast
settings. This caused regular IOs to fail prematurely when they were
merged into failfast requests for readahead.
Niel Lambrechts could trigger the problem semi-reliably on ext4 when
resuming from STR. ext4 uses readahead when reading inodes and
combined with the deterministic extra SATA PHY exception cycle during
resume on the specific configuration, non-readahead inode read would
fail causing ext4 errors. Please read the following thread for
details.
http://lkml.org/lkml/2009/5/23/21
This patch makes block layer reject merging if the failfast settings
don't match. This is correct but likely to lower IO performance by
preventing regular IOs from mingling into surrounding readahead
requests. Changes to allow such mixed merges and handle errors
correctly will be added later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Cc: Theodore Tso <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
When doing an unexpected shutdown like kexec the cciss
firmware might still have some commands in flight, which
it is trying to complete.
The driver is doing it's best on resetting the HBA,
but sadly there's a firmware issue causing the firmware
_not_ to abort or drop old commands.
So the firmware will send us commands which we haven't
accounted for, causing the driver to panic.
With this patch we're just ignoring these commands as
there is nothing we could be doing with them anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
Remove the read-first logic from atomic64_xchg() and simplify
the loop.
This function was the last user of __atomic64_read() - remove it.
Also, change the 'real_val' assumption from the somewhat quirky
1ULL << 32 value to the (just as arbitrary, but simpler) value
of 0.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
LKML-Reference: <tip-05118ab8859492ac9ddda0154cf90e37b0a4a0b0@git.kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
atomic64_t primitives are used by a handful of drivers,
so export the APIs consistently. These were inlined
before.
Also mark atomic64_32.o a core object, so that the symbols
are available even if not linked to core kernel pieces.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
LKML-Reference: <tip-05118ab8859492ac9ddda0154cf90e37b0a4a0b0@git.kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For systems which do not define PHYS_OFFSET as 0 pfn_valid() may falsely
have returned 0 on most configurations. Bug introduced by commit
752fbeb2e3555c0d236e992f1195fd7ce30e728d (linux-mips.org) rsp.
6f284a2ce7 (kernel.org) titled "[MIPS]
FLATMEM: introduce PHYS_OFFSET."
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the cavium PCI files to the arch/mips/pci directory. Also cleanup
comment formatting and code layout. Code from pci-common.c, was moved
into other files.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an o32 process generates a core dump on a 64 bit kernel, the core file
will not be correctly recognized. This is because ELF_CORE_COPY_REGS and
ELF_CORE_COPY_TASK_REGS are not correctly defined for o32 and will use
the default register set which would be CONFIG_64BIT in asm/elf.h.
So we'll switch to use the right register defines in this situation by
checking for WANT_COMPAT_REG_H and use the right defines of
ELF_CORE_COPY_REGS and ELF_CORE_COPY_TASK_REGS.
[Ralf: made ELF_CORE_COPY_TASK_REGS() bullet-proof against funny arguments.]
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current ssb irq setup in ssb_mipscore_init has the problem that it
configures some device on some irq without checking that the irq is not
taken by an other device.
For example in my case PCI host is on irq 0 and IPSEC on irq 3.
The current code:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host
But now IPSEC irq is not routed anymore to the mips code and dev->irq is
wrong. This causes a problem described in [1].
This patch tries to solve the problem by making set_irq configure the
device we want to take the irq on the shared irq0. The previous example
becomes:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host:
- irq 3 is already taken by IPSEC. do a set_irq 3->0 on IPSEC
I also added some code to print the irq configuration after irq setup to
allow easier debugging. And I add extra checking in ssb_mips_irq to report
device without irq or device with not routed irq.
[1] http://www.danm.de/files/src/bcm5365p/REPORTED_DEVICES
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This revises the sync-4k so it will boot and operate since the removal of
expirelo from the timer code.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to move the gcmp_probe call to before the use of and selection of
the smp_ops functions. This allows malta with 1004K to work.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of the CMP support was added before, this mostly correct compile
problems but adds a platform specific translation for the interrupt number
based on cpu number.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This takes the current IPI interrupt assignment from the fix number of 4
to the number of CPUs defined in the system.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch extends the GIC interrupt handling beyond the current 32 bit
range as well as extending the number of interrupts based on the number
of CPUs.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs implement mipsr2, but because they are a super-set of mips64r2 do
not define CONFIG_CPU_MIPS64_R2. Cavium OCTEON falls into this category.
We would still like to use the optimized implementation, so since we have
already checked for CONFIG_CPU_MIPSR2, checking for CONFIG_64BIT instead of
CONFIG_CPU_MIPS64_R2 is sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Ralf: I fixed up the numbering in the comment in scall64-n32.S.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@openwrt.org>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
nfsd_open() gets an unrefcounted pointer to the current process's effective
credentials at the top of the function, then calls nfsd_setuser() via
fh_verify() - which may replace and destroy the current process's effective
credentials - and then passes the unrefcounted pointer to dentry_open() - but
the credentials may have been destroyed by this point.
Instead, the value from current_cred() should be passed directly to
dentry_open() as one of its arguments, rather than being cached in a variable.
Possibly fh_verify() should return the creds to use.
This is a regression introduced by
745ca2475a "CRED: Pass credentials through
dentry_open()".
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-and-Verified-By: Steve Dickson <steved@redhat.com>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Register cache space was not being allocated for the final register,
causing bugs when it was used. Allocate space for it.
Also ensure that the final register is displayed in sysfs.
[Commit message rewritten to document actual issue. -- broonie]
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mixer elements created for ASUS eeePC 1000 with ALC269 aren't
standard but strange words like "LineOut". Rename the element names
to follow the standard one like "Headphone" and "Speaker".
Also, split the volumes to each so that the virtual master can control
them.
The alc269_fujitsu_mixer is removed because it's now identical with
the new eeepc mixer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP laptops with AD1984A codecs (at least mobile models) need to set
GPIO1 appropriately to indicate the mute state. The BIOS checks this
bit to judge whether the mute on or off is sent via F8 key.
Without changing this bit, the BIOS can be confused and may toggle
the mute wrongly.
Reference: Novell bnc#515266
https://bugzilla.novell.com/show_bug.cgi?id=515266
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Occasionally we get bugs where atomic_read or atomic_set are
used on atomic64_t variables or vice versa. These bugs don't
generate warnings on x86 because atomic_read and atomic_set are
coded as macros rather than C functions, so we don't get any
type-checking on their arguments; similarly for atomic64_read
and atomic64_set in 64-bit kernels.
This converts them to C functions so that the arguments are
type-checked and bugs like this will get caught more easily. It
also converts atomic_cmpxchg and atomic_xchg, and
atomic64_cmpxchg and atomic64_xchg on 64-bit, so we get
type-checking on their arguments too.
Compiling a typical 64-bit x86 config, this generates no new
warnings, and the vmlinux text is 86 bytes smaller.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
LKML-Reference: <alpine.LFD.2.01.0907021653030.3210@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
