As these function pointers will always point to
the 3945 functions, we can just call them directly
and avoid the indirection.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We currently display the build number only if debugging
is enabled, but it is really helpful so show it all the
time. Also store it so it can be retrieved later via
ethtool.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently iwlwifi will eventually exhaust the station
table when adding the BSSID station for IBSS mode,
unless the interface is set down.
The new mac80211 ibss joined/left notification allows
us to fix that easily by moving the code to add the
IBSS station to the notification, and also adding
code to remove it again when we leave the IBSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We'll need that function for IBSS station management,
so pass it the address, which is the only thing it
uses from the station struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl3945 should not use iwl_add_local_station(..., false)
because that would leave the IWL_STA_UCODE_INPROGRESS flag
set for the station, which is not desirable. Instead it
can use iwl3945_add_bcast_station() here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When adding the broadcast station the link quality command is
generated on demand, sent to device, and disappears. It is thus not
available for later cases when we need to restore stations and need
to send the link quality command afterwards. Now, when first adding the
broadcast station, also generate its link quality command to always be
available for later restoring.
Also fix an issue when adding local stations where the "in progress" state
is never cleared.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Dump the firmware version and build number in case of firmware SW
error. This would help firmware engineer analyze the error log.
Requested-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple error condition require fw/rf reset, driver should check all
the possible errors as long as the error checking functions for the
devices are available.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
wifi/wimax co-exist command is part of _agn device configuration
sequence; move it to iwl-agn-ucode.c which is more appropriate place for the
function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Return -EAGAIN when request tx power information and uCode is not ready;
so it will not confuse with tx power information not available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
sensitivity calibration and chain noise calibration are not available
for all the devices; use .cfg to configure the availability of those
calibration functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable continuous ucode
trace function; put it in .cfg for better control and more
flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable tx power control,
move it to .cfg for better control and more flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The iw_mode will always follow the only vif we
have, but using the vif directly seems easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The "chain_tx_power" debugfs function is to display the tx power per
chain based. Name it "tx_power" is misleading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For the devices do not have power save support, remove the power save
control related debugfs files.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename the current 6000 series Gen2 devices to Gen2a.
Rename the ucode name prefix to iwlwifi-6000g2a.
Also corrected the device IDs for Gen2a series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When we kick off a firmware loading process,
and then unbind from the pci device right
away, we get into trouble. Avoid that by
waiting for the firmware loading to finish
(whether successfully or not) before the
unbind in iwl_pci_remove.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When CONFIG_NET is disabled, the attempt to build wext-priv.c
fails with:
net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:207: error: implicit declaration of function 'call_commit_handler'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
s/X/x
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a little bit of restructuring it isn't necessary to have special
cases in rt2x00queue_write_tx_descriptor for writing the descriptor
for beacons.
Simply split off the kicking of the TX queue to a separate function
with is only called for non-beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the Ralink vendor driver for rt2800 we don't need a full
TXD for a beacon but just a TXWI in front of the actual beacon.
Fix the rt2800pci and rt2800usb beaconing code accordingly.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RXWI processing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXWI writing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should simply follow what the hardware told us it has done.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused RXD_DESC_SIZE define and remove duplicated RXWI definitions
from rt2800.h.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should take the stripping of the IV into account for the txdesc->length
field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places that use > ARRAY_SIZE() instead of
>= ARRAY_SIZE().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a stray null dereference. We initialize "ista" properly later on.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This mutex_unlock() has been here from the initial commit, but as nearly
as I can tell, there isn't a reason for it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From the original report:
"I had problems to get my rtl8185 PCI card running on Sparc64: I always
got an error about "No suitable DMA available" followed by an error
that no device could be detected. When comparing the rtl8180 driver to
others I noticed that others are mostly using DMA_BIT_MASK so I changed
the custom mask to DMA_BIT_MASK(32) which fixed my issue."
Reported-by: Tiziano Müller <tm@dev-zero.ch>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 1f36f774b2 ("Switch !O_CREAT case to use of do_last()") in
2.6.34-rc1 autofs direct mounts stopped working. This is caused by
current->link_count being 0 when ->follow_link() is called from
do_filp_open().
I can't work out why this hasn't been seen before Als patch series.
This patch removes the autofs dependence on current->link_count.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restore the rcu_dereference() calls in conntrack/expectation notifier
and logger registration/unregistration, but use the _protected variant,
which will be required by the upcoming __rcu annotations.
Based on patch by Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This reverts commit 7aee674665.
As it doesn't seem to be universally valid for all mainboard revisions of
the D945GCLF2 and breaks snd-hda-intel/ snd-hda-codec-realtek on the Intel
Corporation "D945GCLF2" (LF94510J.86A.0229.2009.0729.0209) mainboard.
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: <stable@kernel.org> [2.6.33]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the expiration timer for unresolved multicast route entries.
In case new multicast routing requests come in faster than the
expiration timeout occurs (e.g. zap through multicast TV streams), the
timer is prevented from being called at time for already existing entries.
As the single timer is resetted to default whenever a new entry is made,
the timeout for existing unresolved entires are missed and/or not
updated. As a consequence new requests are denied when the limit of
unresolved entries has been reached because old entries live longer than
they are supposed to.
The solution is to reset the timer only for the first unresolved entry
in the multicast routing cache. All other timers are already set and
updated correctly within the timer function itself by now.
Signed-off by: Andreas Meissner <andreas.meissner@sphairon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideapad quirks working for my ThinkPad X100e (microphone is not tested).
Signed-off-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use strict_strtoul as suggested by checkpatch.pl for more strict input
checking.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
