The be_cmd_rx_filter() routine sends a non-embedded cmd to the FW and used
a pre-allocated dma memory to hold the cmd payload. This worked fine when
this cmd was synchronous. This cmd was changed to asynchronous mode by the
commit 8af65c2f4("make the RX_FILTER command asynchronous"). So now when
there are two quick invocations of this cmd, the 2nd request may end up
overwriting the first request, causing FW cmd corruption.
This patch reverts the offending commit and hence fixes the regression.
Fixes: 8af65c2f4("be2net: make the RX_FILTER command asynchronous")
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add be_get_phys_port_id() function to report physical port id. The port id
should be unique across different be2net devices in the system. We use the
chip serial number along with the physical port number for this.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_LOOPBACK_MODE command is always issued from ethtool only in a
process context. So, while waiting for the cmd to complete, the driver
can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done
by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns
only after the cmd completes while the MCCQ is locked).
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues
this cmd and doesn't wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the adapter is in error state, return error from be_mcc_notify()
so that the caller routines need not sleep waiting for a response.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OS2BMC feature will allow the server to communicate with the on-board
BMC/idrac (Baseboard Management Controller) over the LOM via
standard Ethernet.
When OS2BMC feature is enabled, the LOM will filter traffic coming
from the host. If the destination MAC address matches the iDRAC MAC
address, it will forward the packet to the NC-SI side band interface
for iDRAC processing. Otherwise, it would send it out on the wire to
the external network. Broadcast and multicast packets are sent on the
side-band NC-SI channel and on the wire as well. Some of the packet
filters are not supported in the NIC and hence driver will identify
such packets and will hint the NIC to send those packets to the BMC.
This is done by duplicating packets on the management ring. Packets
are sent to the management ring, by setting mgmt bit in the wrb header.
The NIC will forward the packets on the management ring to the BMC
through the side-band NC-SI channel.
Please refer to this online document for more details,
http://www.dell.com/downloads/global/products/pedge/
os_to_bmc_passthrough_a_new_chapter_in_system_management.pdf
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error (related to HW or FW) is detected on a function, the driver
must pro-actively report a "link down" to the stack so that a possible
failover can be initiated. This is being done currently only for some
HW errors. This patch reports a "link down" even for fatal FW errors and
EEH errors.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool statistics is not the right place to display board temperature.
This patch adds support to export die temperature of devices supported
by be2net driver via the sysfs hwmon interface.
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use be_virtfn() to determine a VF instead of !be_physfn() for better
readability.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FW runs out of vlan filters it can either return an
INSUFFICIENT_RESOURCES error or an INSUFFICIENT_VLANS error.
The driver currently checks only for the former error value.
This patch adds a check for the latter value too.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for spoofchk configuration for VFs.
When it is enabled, "spoof checking" is done for both MAC-address and VLAN.
For each VF, the HW ensures that the source MAC address (or vlan) of
every outgoing packet exists in the MAC-list (or vlan-list) configured
for RX filtering for that VF. If not, the packet is dropped and an error
is reported to the driver in the TX completion; this is reflected in the
"tx_spoof_check_err" ethtool counter.
This feature is supported in Skyhawk FW version 10.6.31.0 and above.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing this cmd for more than 8 EQs does not have the intended effect
even on BEx and Skyhawk-R.
This patch fixes this by issuing this cmd for upto 8 EQs at a time.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a PF does not restrict its VF interface from enabling vlan
promiscuous mode. This breaks vlan isolation when a vlan
(transparent tagging) is configured on a VF.
This patch fixes this problem by disabling the vlan promisc capability
for VFs.
Reported-by: Yoann Juet <veilletechno-irts@univ-nantes.fr>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the .sriov_configure() PCI method to allow for
runtime enabling/disabling of VFs. The module param "num_vfs" is now
deprecated.
At the time of driver load the PF-pool resources are allocated to the PF.
When the user enables VFs, the resources are then re-distributed across
PFs and VFs based on the number of VFs enabled.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SR-IOV is enabled in the adapter, the FW distributes resources
evenly across the PF and it's VFs. This is currently done only for some
resources.
This patch adds support for a new cmd that queries the FW for the list
of resources for which the distribution is allowed and distributes them
accordingly.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE2, BE3 and Skhawk-R chips one non-RSS (called "default") RXQ was
needed to receive non-IP traffic. Some FW versions now export a
capability called IFACE_FLAGS_DEFQ_RSS where this requirement doesn't hold.
On such FWs the driver now does not create the non-RSS default queue.
This prevents wasting one RXQ per VF.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The steps needed for Lancer's reset/initialization sequence are:
a) wait for SLIPORT_STAUS RDY bit to be set
b) set the SLIPORT_CONTROL IP bit
c) repeat step "a"
The code needed for this sequence is already covered by the be_func_init()
routine (with minor modifications.) So, get rid of the
lancer_test_and_set_rdy_state() and lancer_provisioning_error() routines
that unnecessarily duplicate this code. Also fixed the error recovery
function to take care of these changes
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function initialization sequence is executed in be_probe(), be_resume
and be_eeh_resume(). Move this code to a new routine called be_func_init()
to prevent code duplication.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for processing the port misconfigure async
event generated by the FW. This event is generated typically when an
optical module is incorrectly installed or is faulty.
This patch also moves the port_name field to the adapter struct for
logging the event. As the be_cmd_query_port_name() call is now moved
to be_get_config(), it is modified to use the mailbox instead of MCCQ
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch passes BE_IF_FLAGS_XXX flags to be_cmd_rx_filter() routine
instead of the IFF_XXX flags. Doing this gets rid of the code to convert
the IFF_XXX flags to the BE_IF_FLAGS_XXX used by the FW cmd. The patch
also removes code for setting if_flags_mask that was duplicated for each
filter mode.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While sending FW update cmds to the FW, the driver specifies the "type"
of each component that needs to be flashed. The FW then picks the offset
in the flash area at which the componnet is to be flashed. This doesn't work
when new components that the current FW doesn't recognize, need to be
flashed. Recent FWs (10.2 and above) support a scheme of FW-update wherein
the "offset" of the component in the flash area can be specified instead
of the "type". This patch uses the "offset" based FW-update mechanism and
only when it fails, it fallsback to the old "type" based update.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routines that are called only inside one src file must remain in that
file itself. Including them in a header file that is used for exporting
routine/struct definitions, causes unnecessary compilation of other
src files, when such a routine is modified.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
be_cmds.c:2750:5: warning: symbol 'be_cmd_set_qos' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When max_tx_rate is set via bw_max in the NIC resource desc, bw_min must be
set to 0.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a log message in case of POST timeout in Lancer to
help debugging failure cases. It also logs sliport_status register value in
case of POST timeout.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support for this exists only in skyhawk FW.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes alignment whereever it doesn't match the open parenthesis
alignment.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes multiple assignments on a single line as warned
by checkpatch.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary spaces after typecasts as per checkpatch warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpatch warnings about blank lines after an open brace '{'.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes multiple blank lines in the driver as per checkpatch
warnings.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes checkpatch warnings in be2net by adding a blank line
between declaration and code blocks.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a sparse warning about missing static declaration that was
introduced by the following commit:
fixes: 936767039c ("be2net: send a max of 8 EQs to be_cmd_modify_eqd() on Lancer")
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the ethtool port-type/supported/advertising values based on the
cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from
the transceiver data fetched from the FW.
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the dump-module-eeprom and module-info
ethtool options.
Signed-off-by: Mark Leonard <mark.leonard@emulex.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations the FW doesn't allow changing flow control settings
of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW
doesn't report an error to the driver.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace strcpy with strlcpy, as it avoids a possible buffer overflow.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following minor issues with log messages in be2net:
1) Period is not required at the end of log message.
2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely
ignore async events from FW it's not interested in.
3) Reword a log message for better readability to say that SRIOV
"is disabled" rather than "not supported".
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following log messages to help debugging
failure cases:
1) log FW version number: this is useful when driver initialization
fails and the FW version number cannot be queried via ethtool
2) per function resource limits for BEx chips: these values are
currently being printed only for Skyhawk and Lancer
3) PCI BAR mapping failure
4) function_mode/caps queried from FW: this helps catch any FW bugs
that could advertise wrong capabilities to the driver
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to delete an existing FW-dump in Lancer via ethtool.
Initiating a new dump is not allowed if a FW dump is already present in the
adapter. The existing dump has to be first explicitly deleted.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pointer to adapter struct is passed anyway to all of the FW-cmd routines
in be_cmds.c. For routines which query data from FW, the adapter pointer
is enough to return the queried fields.
There is no need to separately pass pointers to individual members of
the adapter structure. This patch fixes this for be_cmd_get_fw_ver()
and be_cmd_get_fw_cfg() routines.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FW stops responding with completions, return -ETIMEDOUT error
(instead of -1) to the stack.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
