Frank reported kernel panic when he disabled several cores in BIOS
via following option:
Core Disable Bitmap(Hex) [0]
with number 0xFFE, which leaves 16 CPUs in system (out of 48).
The kernel panic below goes along with following messages:
smpboot: Max logical packages: 2^M
smpboot: APIC(0) Converting physical 0 to logical package 0^M
smpboot: APIC(20) Converting physical 1 to logical package 1^M
smpboot: APIC(40) Package 2 exceeds logical package map^M
smpboot: CPU 8 APICId 40 disabled^M
smpboot: APIC(60) Package 3 exceeds logical package map^M
smpboot: CPU 12 APICId 60 disabled^M
...
general protection fault: 0000 [#1] SMP^M
Modules linked in:^M
CPU: 15 PID: 1 Comm: swapper/0 Not tainted 4.7.0-rc5+ #1^M
Hardware name: SGI UV300/UV300, BIOS SGI UV 300 series BIOS 05/25/2016^M
task: ffff8801673e0000 ti: ffff8801673ac000 task.ti: ffff8801673ac000^M
RIP: 0010:[<ffffffff81014d54>] [<ffffffff81014d54>] uncore_change_context+0xd4/0x180^M
...
[<ffffffff810158ac>] uncore_event_init_cpu+0x6c/0x70^M
[<ffffffff81d8c91c>] intel_uncore_init+0x1c2/0x2dd^M
[<ffffffff81d8c75a>] ? uncore_cpu_setup+0x17/0x17^M
[<ffffffff81002190>] do_one_initcall+0x50/0x190^M
[<ffffffff810ab193>] ? parse_args+0x293/0x480^M
[<ffffffff81d87365>] kernel_init_freeable+0x1a5/0x249^M
[<ffffffff81d86a35>] ? set_debug_rodata+0x12/0x12^M
[<ffffffff816dc19e>] kernel_init+0xe/0x110^M
[<ffffffff816e93bf>] ret_from_fork+0x1f/0x40^M
[<ffffffff816dc190>] ? rest_init+0x80/0x80^M
The reason for the panic is wrong value of __max_logical_packages,
which lets logical_package_map uninitialized and the uncore code
relying on this map being properly initialized (maybe we should
add some safety checks there as well).
The __max_logical_packages is computed as:
DIV_ROUND_UP(total_cpus, ncpus);
- ncpus being number of cores
With above BIOS setup we get total_cpus == 16 which set
__max_logical_packages to 2 (ncpus is 12).
Once topology_update_package_map processes CPU with logical
pkg over 2 we display above messages and fail to initialize
the physical_to_logical_pkg map, which makes the uncore code
crash.
The fix is to remove logical_package_map bitmap completely
and keep and update the logical_packages number instead.
After we enumerate all the present CPUs, we check if the
enumerated logical packages count is within its computed
maximum from BIOS data.
If it's not the case, we set this maximum to the new enumerated
value and freeze any new addition of logical packages.
The freeze is because lot of init code like uncore/rapl/cqm
depends on having maximum logical package value set to allocate
their data, so we can't change it later on.
Prarit Bhargava tested the patch and confirms that it solves
the problem:
From dmidecode:
Core Count: 24
Core Enabled: 24
Thread Count: 48
Orig kernel boot log:
[ 0.464981] smpboot: Max logical packages: 19
[ 0.469861] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.477261] smpboot: APIC(40) Converting physical 1 to logical package 1
[ 0.484760] smpboot: APIC(80) Converting physical 2 to logical package 2
[ 0.492258] smpboot: APIC(c0) Converting physical 3 to logical package 3
1. nr_cpus=8, should stop enumerating in package 0:
[ 0.533664] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.539596] smpboot: Max logical packages: 19
2. max_cpus=8, should still enumerate all packages:
[ 0.526494] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.532428] smpboot: APIC(40) Converting physical 1 to logical package 1
[ 0.538456] smpboot: APIC(80) Converting physical 2 to logical package 2
[ 0.544486] smpboot: APIC(c0) Converting physical 3 to logical package 3
[ 0.550524] smpboot: Max logical packages: 19
3. nr_cpus=49 ( 2 socket + 1 core on 3rd socket), should stop enumerating in
package 2:
[ 0.521378] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.527314] smpboot: APIC(40) Converting physical 1 to logical package 1
[ 0.533345] smpboot: APIC(80) Converting physical 2 to logical package 2
[ 0.539368] smpboot: Max logical packages: 19
4. maxcpus=49, should still enumerate all packages:
[ 0.525591] smpboot: APIC(0) Converting physical 0 to logical package 0
[ 0.531525] smpboot: APIC(40) Converting physical 1 to logical package 1
[ 0.537547] smpboot: APIC(80) Converting physical 2 to logical package 2
[ 0.543579] smpboot: APIC(c0) Converting physical 3 to logical package 3
[ 0.549624] smpboot: Max logical packages: 19
5. kdump (nr_cpus=1) works as well.
Reported-by: Frank Ramsay <framsay@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20160815101700.GA30090@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Similar to:
efaad554b4 ("x86/microcode/intel: Fix initrd loading with CONFIG_RANDOMIZE_MEMORY=y")
... fix microcode loading from the initrd on AMD by adding the
randomization offset to the microcode patch container within the initrd.
Reported-and-tested-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-tip-commits@vger.kernel.org
Link: http://lkml.kernel.org/r/20160817113314.GA19221@nazgul.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
__replace_page() wronlgy calls mem_cgroup_cancel_charge() in "success" path,
it should only do this if page_check_address() fails.
This means that every enable/disable leads to unbalanced mem_cgroup_uncharge()
from put_page(old_page), it is trivial to underflow the page_counter->count
and trigger OOM.
Reported-and-tested-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: stable@vger.kernel.org # 3.17+
Fixes: 00501b531c ("mm: memcontrol: rewrite charge API")
Link: http://lkml.kernel.org/r/20160817153629.GB29724@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Per NVMe-over-Fabrics 1.0 spec, sqsize is represented as
a 0-based value.
Also per spec, the RDMA binding values shall be set
to sqsize, which makes hsqsize 0-based values.
Thus, the sqsize during NVMf connect() is now:
[root@fedora23-fabrics-host1 for-48]# dmesg
[ 318.720645] nvme_fabrics: nvmf_connect_admin_queue(): sqsize for
admin queue: 31
[ 318.720884] nvme nvme0: creating 16 I/O queues.
[ 318.810114] nvme_fabrics: nvmf_connect_io_queue(): sqsize for i/o
queue: 127
Finally, current interpretation implies hrqsize is 1's based
so set it appropriately.
Reported-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Upon admin queue connect(), the rdma qp was being
set based on NVMF_AQ_DEPTH. However, the fabrics layer was
using the sqsize field value set for I/O queues for the admin
queue, which threw the nvme layer and rdma layer off-whack:
root@fedora23-fabrics-host1 nvmf]# dmesg
[ 3507.798642] nvme_fabrics: nvmf_connect_admin_queue():admin sqsize
being sent is: 128
[ 3507.798858] nvme nvme0: creating 16 I/O queues.
[ 3507.896407] nvme nvme0: new ctrl: NQN "nullside-nqn", addr
192.168.1.3:4420
Thus, to have a different admin queue value, we use
NVMF_AQ_DEPTH for connect() and RDMA private data
as the minimum depth specified in the NVMe-over-Fabrics 1.0 spec
(and in that RDMA private data we treat hrqsize as 1's-based
value, per current understanding of the fabrics spec).
Reported-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
The host will be sending sqsize 0-based hsqsize value,
the target need to be adjusted as well.
Signed-off-by: Jay Freyensee <james_p_freyensee@linux.intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
* pm-sleep:
PM / hibernate: Fix rtree_next_node() to avoid walking off list ends
x86/power/64: Use __pa() for physical address computation
PM / sleep: Update some system sleep documentation
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
Cong Wang says:
====================
net_sched: tc action fixes and updates
This patchset fixes a few regressions caused by the previous
code refactor and more. Thanks to Jamal for catching them!
Note, patch 3/7 and 4/7 are not strictly necessary for this patchset,
I just want to carry them together.
---
v4: adjust an indention for Jamal
add two more patches
v3: avoid list for fast path, suggested by Jamal
v2: replace flex_array with regular dynamic array
keep tcf_action_stats_update() in act_api.h
fix macro typos found by Amir
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The act_police uses its own code to walk the
action hashtable, which leads to that we could
not flush standalone tc police actions, so just
switch to tcf_generic_walker() like other actions.
(Joint work from Roman and Cong.)
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal reported a crash when we create a police action
with a specific index, this is because the init logic
is not correct, we should always create one for this
case. Just unify the logic with other tc actions.
Fixes: a03e6fe569 ("act_police: fix a crash during removal")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tcf_exts belongs to filters, should not be visible
to plain tc actions.
Cc: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is harmless because all users pass 'a' to this macro.
Fixes: 00175aec94 ("net/sched: Macro instead of CONFIG_NET_CLS_ACT ifdef")
Cc: Amir Vadai <amir@vadai.me>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This list_del() for tc action is not needed actually,
because we only use this list to chain bulk operations,
therefore should not be carried for latter operations.
Fixes: ec0595cc44 ("net_sched: get rid of struct tcf_common")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After refactoring tc_action into tcf_common, we no
longer need to cleanup temporary "actions" in list,
they are permanently stored in the hashtable.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-08-16
This series contains fixes to e1000e, igb, ixgbe and i40e.
Kshitiz Gupta provides a fix for igb to resolve the PHY delay compensation
math in several functions.
Jarod Wilson provides a fix for e1000e which had to broken up into 2
patches, first is prepares the driver for expanding the list of NICs
that have occasional ~10 hour clock jumps when being used for PTP.
Second patch actually fixes i218 silicon which has been experiencing
the clock jumps while using PTP.
Alex provides 2 patches for ixgbe now that he is back at Intel. First
fixes setting VLNCTRL.VFE bit, which was left unchanged in earlier patches
which resulted in disabling VLAN filtering for all the VFs. Second
corrects the support for disabling the VLAN tag filtering via the
feature bit.
Lastly, David fixes i40e which was causing a kernel panic when
non-contiguous traffic classes or traffic classes not starting with TC0,
were configured on a link partner switch. To fix this, changed the
logic when determining the total number of TCs enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: IPv4 UC router fixes
Ido says:
Patches 1-3 fix a long standing problem in the driver's init sequence,
which manifests itself quite often when routing daemons try to configure
an IP address on registered netdevs that don't yet have an associated
vPort.
Patches 4-9 add missing packet traps for the router to work properly and
also fix ordering issue following the recent changes to the driver's init
sequence.
The last patch isn't related to the router, but fixes a general problem
in which under certain conditions packets aren't trapped to CPU.
v1->v2:
- Change order of patch 7
- Add patch 6 following Ilan's comment
- Add patchset name and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:
(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)
Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.
Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralue pack function needs to set op, otherwise it is 0 for add always.
Fixes: d5a1c749d2 ("mlxsw: reg: Add Router Algorithmic LPM Unicast Entry Register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following traps:
1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.
2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.
3) OSPF packets.
Fixes: 7b27ce7bb9 ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_lookup_listener() and inet6_lookup_listener() no longer
take a reference on the found listener.
This minimal patch adds back the refcounting, but we might do
this differently in net-next later.
Fixes: 3b24d854cb ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Reported-and-tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We should report the over quota message to the right net namespace
instead of the init netns.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As per the GICv3 specification, to power down a processor using GICv3
and allow automatic power-on if an interrupt must be sent to a processor,
software must set Enable to zero for all interrupt groups(by writing
to GICC_CTLR or ICC_IGRPEN{0,1}_EL1/3 as appropriate.
When commit 3708d52fc6 ("irqchip: gic-v3: Implement CPU PM notifier")
was introduced there were no firmware implementations(in particular PSCI)
handling this.
Linux kernel may not be aware of the CPU power state details and might
fail to identify the power states that require quiescing the CPU
interface. Even if it can be aware of those details, it can't determine
which CPU power state have been triggered at the platform level and how
the power control is implemented.
This patch make disabling redistributor and group1 non-secure interrupts
in the power down path and re-enabling of redistributor in the power-up
path conditional. It will be handled in the kernel if and only if the
non-secure accesses are permitted to access and modify control registers.
It is left to the platform implementation otherwise.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On systems where a single CPU is present, the GIC may not support
having SGIs delivered to a target list. In that case, we use the
self-SGI mechanism to allow the interrupt to be delivered locally.
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This fixes a long-standing bug that caused a flood of messages like:
"md: delaying data-check of md1 until md2 has finished (they share one
or more physical units)"
It can be reproduced like this:
1. Create at least 3 raid1 arrays on a pair of disks, each on different
partitions.
2. Request a sync operation like 'check' or 'repair' on 2 arrays by
writing to their md/sync_action attribute files. One operation should
start and one should be delayed and a message like the above will be
printed.
3. Issue a write to the third array. Each write will cause 2 copies of
the message to be printed.
This happens when wake_up(&resync_wait) is called, usually by
md_check_recovery(). Then the delayed sync thread again prints the
message and is put to sleep. This patch adds a check in md_do_sync() to
prevent printing this message more than once for the same pair of
devices.
Reported-by: Sven Koehler <sven.koehler@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151801
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
The ret is not needed anymore since we have already
move resync_start into md_do_sync in commit 41a9a0d.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Literal loads of virtual addresses are subject to runtime relocation when
CONFIG_RELOCATABLE=y, and given that the relocation routines run with the
MMU and caches enabled, literal loads of relocated values performed with
the MMU off are not guaranteed to return the latest value unless the
memory covering the literal is cleaned to the PoC explicitly.
So defer the literal load until after the MMU has been enabled, just like
we do for primary_switch() and secondary_switch() in head.S.
Fixes: 1e48ef7fcc ("arm64: add support for building vmlinux as a relocatable PIE binary")
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since asm/acpi.h is only included by linux/acpi.h when CONFIG_ACPI is
enabled, disabling the latter leads to the following build error on
arm64:
arch/arm64/mm/numa.c: In function ‘arm64_numa_init’:
arch/arm64/mm/numa.c:395:24: error: ‘arm64_acpi_numa_init’ undeclared (first use in this function)
if (!acpi_disabled && !numa_init(arm64_acpi_numa_init))
This patch include the asm/acpi.h explicitly in arch/arm64/mm/numa.c for
the arm64_acpi_numa_init() definition.
Fixes: d8b47fca8c ("arm64, ACPI, NUMA: NUMA support based on SRAT and SLIT")
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Change my email address to kernel.org account instead of Samsung one.
Add Bartlomiej Zolnierkiewicz as a co-maintainer of Maxim and Samsung
PMIC drivers. These are used on many of our boards along with Exynos
SoCs and Samsung R&D Institute Poland can still take care of them.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Otherwise, if nfnetlink_log.ko is not loaded, we cannot add rules
to log packets to the userspace when we specify it with arp family,
such as:
# nft add rule arp filter input log group 0
<cmdline>:1:1-37: Error: Could not process rule: No such file or
directory
add rule arp filter input log group 0
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We should skip the conntracks that belong to a different namespace,
otherwise other unrelated netns's conntrack entries will be dumped via
/proc/net/nf_conntrack.
Fixes: 56d52d4892 ("netfilter: conntrack: use a single hashtable for all namespaces")
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
At imx6ul_init_machine, it calls imx6ul_pm_init which needs to find
platform device for ocram, but the default populate platform device is at
of_platform_default_populate_init, which is located at arch_initcall_sync,
and called later than arch_initcall (.init_machine is located at that).
So below warning message will be showed during boots up:
imx6q_suspend_init: failed to find ocram device!
imx6_pm_common_init: No DDR LPM support with suspend -19!
Due to lack of ocram device, the suspend mode "mem" which needs ocram to
store suspend routine code is invalid.
This commit populates platform device before imx6ul_pm_init like other
imx6 platforms do, and the suspend mode "mem" can work successfully.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fixes: 850bea2335 ("arm: Remove unnecessary of_platform_populate with default match table")
Cc: Anson Huang <anson.huang@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The raid0 MD personality does not start a raid0 array with any of its
data devices missing.
dm-raid was removing data/metadata device pairs unconditionally if it
failed to read a superblock off the respective metadata device of such
pair, resulting in failure to start arrays with the raid0 personality.
Avoid removing any data/metadata device pairs in case of raid0
(e.g. lvm2 segment type 'raid0_meta') thus allowing MD to start the
array.
Also, avoid region size validation for raid0.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
cgroup_threadgroup_rwsem is acquired in read mode during process exit
and fork. It is also grabbed in write mode during
__cgroups_proc_write(). I've recently run into a scenario with lots
of memory pressure and OOM and I am beginning to see
systemd
__switch_to+0x1f8/0x350
__schedule+0x30c/0x990
schedule+0x48/0xc0
percpu_down_write+0x114/0x170
__cgroup_procs_write.isra.12+0xb8/0x3c0
cgroup_file_write+0x74/0x1a0
kernfs_fop_write+0x188/0x200
__vfs_write+0x6c/0xe0
vfs_write+0xc0/0x230
SyS_write+0x6c/0x110
system_call+0x38/0xb4
This thread is waiting on the reader of cgroup_threadgroup_rwsem to
exit. The reader itself is under memory pressure and has gone into
reclaim after fork. There are times the reader also ends up waiting on
oom_lock as well.
__switch_to+0x1f8/0x350
__schedule+0x30c/0x990
schedule+0x48/0xc0
jbd2_log_wait_commit+0xd4/0x180
ext4_evict_inode+0x88/0x5c0
evict+0xf8/0x2a0
dispose_list+0x50/0x80
prune_icache_sb+0x6c/0x90
super_cache_scan+0x190/0x210
shrink_slab.part.15+0x22c/0x4c0
shrink_zone+0x288/0x3c0
do_try_to_free_pages+0x1dc/0x590
try_to_free_pages+0xdc/0x260
__alloc_pages_nodemask+0x72c/0xc90
alloc_pages_current+0xb4/0x1a0
page_table_alloc+0xc0/0x170
__pte_alloc+0x58/0x1f0
copy_page_range+0x4ec/0x950
copy_process.isra.5+0x15a0/0x1870
_do_fork+0xa8/0x4b0
ppc_clone+0x8/0xc
In the meanwhile, all processes exiting/forking are blocked almost
stalling the system.
This patch moves the threadgroup_change_begin from before
cgroup_fork() to just before cgroup_canfork(). There is no nee to
worry about threadgroup changes till the task is actually added to the
threadgroup. This avoids having to call reclaim with
cgroup_threadgroup_rwsem held.
tj: Subject and description edits.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Zefan Li <lizefan@huawei.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tejun Heo <tj@kernel.org>
Change my email address to kernel.org instead of Samsung one for the
purpose of any future contact. The copyrights remain untouched and are
attributed to Samsung.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit:
d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
several return values were added to a void function resulting in the following warnings:
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:175:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:183:4: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:190:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:195:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:200:3: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c:211:2: warning: 'return' with a value, in function returning void [enabled by default]
clocksource/mips-gic-timer.c: At top level:
clocksource/mips-gic-timer.c:213:1: warning: comparison of distinct pointer types lacks a cast [enabled by default]
clocksource/mips-gic-timer.c: In function 'gic_clocksource_of_init':
clocksource/mips-gic-timer.c:183:18: warning: ignoring return value of 'PTR_ERR', declared with attribute warn_unused_result [-Wunused-result]
Given that the addition of the return values was intentional, it seems
that the conversion of the containing function from void to int was
simply overlooked.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Fixes: d8152bf85d ("clocksource/drivers/mips-gic-timer: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-3-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I could not figure out why, but GCC cannot prove that the
kona_timer_init() function always initializes its two outputs,
and we get a warning for the use of the 'lsw' variable later,
which is obviously correct.
drivers/clocksource/bcm_kona_timer.c: In function 'kona_timer_init':
drivers/clocksource/bcm_kona_timer.c:119:13: error: 'lsw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Slightly reordering the loop makes the warning disappear, after
it becomes more obvious to the compiler that the loop is
always entered on the first iteration.
As pointed out by Ray Jui, there is a related problem in the
way we deal with the loop running into the limit, as we just
keep going there with an invalid counter data, so instead we
now propagate a -ETIMEDOUT result to the caller.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Link: http://lkml.kernel.org/r/1471429296-9053-2-git-send-email-daniel.lezcano@linaro.org
Link: https://patchwork.kernel.org/patch/9174261/
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While converting the init function to return an error, the wrong clock
was get. This leads to the wrong clock rate and slows down the kernel.
For example, it affects typical boot time:
- without fix: over 1 minute
- with fix: 15 seconds
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 12549e27c6 ("clocksource/drivers/time-armada-370-xp: Convert init function to return error")
Link: http://lkml.kernel.org/r/1471429296-9053-1-git-send-email-daniel.lezcano@linaro.org
[ Refined the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After commit b34f2bc ("arm64: KVM: Make ICC_SRE_EL1 access return the
configured SRE value") we report SRE value to 64-bit guest, but 32-bit
one still handled as RAZ/WI what leads to funny promise we do not keep:
"GICv3: GIC: unable to set SRE (disabled at EL2), panic ahead"
Instead, return the actual value of the ICC_SRE_EL1 register that the
guest should see.
[ Tweaked commit message - Christoffer ]
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
