Pull cpu hotplug updates from Thomas Gleixner:
"This is the first part of the ongoing cpu hotplug rework:
- Initial implementation of the state machine
- Runs all online and prepare down callbacks on the plugged cpu and
not on some random processor
- Replaces busy loop waiting with completions
- Adds tracepoints so the states can be followed"
More detailed commentary on this work from an earlier email:
"What's wrong with the current cpu hotplug infrastructure?
- Asymmetry
The hotplug notifier mechanism is asymmetric versus the bringup and
teardown. This is mostly caused by the notifier mechanism.
- Largely undocumented dependencies
While some notifiers use explicitely defined notifier priorities,
we have quite some notifiers which use numerical priorities to
express dependencies without any documentation why.
- Control processor driven
Most of the bringup/teardown of a cpu is driven by a control
processor. While it is understandable, that preperatory steps,
like idle thread creation, memory allocation for and initialization
of essential facilities needs to be done before a cpu can boot,
there is no reason why everything else must run on a control
processor. Before this patch series, bringup looks like this:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring the rest up
- All or nothing approach
There is no way to do partial bringups. That's something which is
really desired because we waste e.g. at boot substantial amount of
time just busy waiting that the cpu comes to life. That's stupid
as we could very well do preparatory steps and the initial IPI for
other cpus and then go back and do the necessary low level
synchronization with the freshly booted cpu.
- Minimal debuggability
Due to the notifier based design, it's impossible to switch between
two stages of the bringup/teardown back and forth in order to test
the correctness. So in many hotplug notifiers the cancel
mechanisms are either not existant or completely untested.
- Notifier [un]registering is tedious
To [un]register notifiers we need to protect against hotplug at
every callsite. There is no mechanism that bringup/teardown
callbacks are issued on the online cpus, so every caller needs to
do it itself. That also includes error rollback.
What's the new design?
The base of the new design is a symmetric state machine, where both
the control processor and the booting/dying cpu execute a well
defined set of states. Each state is symmetric in the end, except
for some well defined exceptions, and the bringup/teardown can be
stopped and reversed at almost all states.
So the bringup of a cpu will look like this in the future:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
bring itself up
The synchronization step does not require the control cpu to wait.
That mechanism can be done asynchronously via a worker or some
other mechanism.
The teardown can be made very similar, so that the dying cpu cleans
up and brings itself down. Cleanups which need to be done after
the cpu is gone, can be scheduled asynchronously as well.
There is a long way to this, as we need to refactor the notion when a
cpu is available. Today we set the cpu online right after it comes
out of the low level bringup, which is not really correct.
The proper mechanism is to set it to available, i.e. cpu local
threads, like softirqd, hotplug thread etc. can be scheduled on that
cpu, and once it finished all booting steps, it's set to online, so
general workloads can be scheduled on it. The reverse happens on
teardown. First thing to do is to forbid scheduling of general
workloads, then teardown all the per cpu resources and finally shut it
off completely.
This patch series implements the basic infrastructure for this at the
core level. This includes the following:
- Basic state machine implementation with well defined states, so
ordering and prioritization can be expressed.
- Interfaces to [un]register state callbacks
This invokes the bringup/teardown callback on all online cpus with
the proper protection in place and [un]installs the callbacks in
the state machine array.
For callbacks which have no particular ordering requirement we have
a dynamic state space, so that drivers don't have to register an
explicit hotplug state.
If a callback fails, the code automatically does a rollback to the
previous state.
- Sysfs interface to drive the state machine to a particular step.
This is only partially functional today. Full functionality and
therefor testability will be achieved once we converted all
existing hotplug notifiers over to the new scheme.
- Run all CPU_ONLINE/DOWN_PREPARE notifiers on the booting/dying
processor:
Control CPU Booting CPU
do preparatory steps
kick cpu into life
do low level init
sync with booting cpu sync with control cpu
wait for boot
bring itself up
Signal completion to control cpu
In a previous step of this work we've done a full tree mechanical
conversion of all hotplug notifiers to the new scheme. The balance
is a net removal of about 4000 lines of code.
This is not included in this series, as we decided to take a
different approach. Instead of mechanically converting everything
over, we will do a proper overhaul of the usage sites one by one so
they nicely fit into the symmetric callback scheme.
I decided to do that after I looked at the ugliness of some of the
converted sites and figured out that their hotplug mechanism is
completely buggered anyway. So there is no point to do a
mechanical conversion first as we need to go through the usage
sites one by one again in order to achieve a full symmetric and
testable behaviour"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
cpu/hotplug: Document states better
cpu/hotplug: Fix smpboot thread ordering
cpu/hotplug: Remove redundant state check
cpu/hotplug: Plug death reporting race
rcu: Make CPU_DYING_IDLE an explicit call
cpu/hotplug: Make wait for dead cpu completion based
cpu/hotplug: Let upcoming cpu bring itself fully up
arch/hotplug: Call into idle with a proper state
cpu/hotplug: Move online calls to hotplugged cpu
cpu/hotplug: Create hotplug threads
cpu/hotplug: Split out the state walk into functions
cpu/hotplug: Unpark smpboot threads from the state machine
cpu/hotplug: Move scheduler cpu_online notifier to hotplug core
cpu/hotplug: Implement setup/removal interface
cpu/hotplug: Make target state writeable
cpu/hotplug: Add sysfs state interface
cpu/hotplug: Hand in target state to _cpu_up/down
cpu/hotplug: Convert the hotplugged cpu work to a state machine
cpu/hotplug: Convert to a state machine for the control processor
cpu/hotplug: Add tracepoints
...
Pull irq updates from Thomas Gleixner:
"The 4.6 pile of irq updates contains:
- Support for IPI irqdomains to support proper integration of IPIs to
and from coprocessors. The first user of this new facility is
MIPS. The relevant MIPS patches come with the core to avoid merge
ordering issues and have been acked by Ralf.
- A new command line option to set the default interrupt affinity
mask at boot time.
- Support for some more new ARM and MIPS interrupt controllers:
tango, alpine-msix and bcm6345-l1
- Two small cleanups for x86/apic which we merged into irq/core to
avoid yet another branch in x86 with two tiny commits.
- The usual set of updates, cleanups in drivers/irqchip. Mostly in
the area of ARM-GIC, arada-37-xp and atmel chips. Nothing
outstanding here"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
irqchip/irq-alpine-msi: Release the correct domain on error
irqchip/mxs: Fix error check of of_io_request_and_map()
irqchip/sunxi-nmi: Fix error check of of_io_request_and_map()
genirq: Export IRQ functions for module use
irqchip/gic/realview: Support more RealView DCC variants
Documentation/bindings: Document the Alpine MSIX driver
irqchip: Add the Alpine MSIX interrupt controller
irqchip/gic-v3: Always return IRQ_SET_MASK_OK_DONE in gic_set_affinity
irqchip/gic-v3-its: Mark its_init() and its children as __init
irqchip/gic-v3: Remove gic_root_node variable from the ITS code
irqchip/gic-v3: ACPI: Add redistributor support via GICC structures
irqchip/gic-v3: Add ACPI support for GICv3/4 initialization
irqchip/gic-v3: Refactor gic_of_init() for GICv3 driver
x86/apic: Deinline _flat_send_IPI_mask, save ~150 bytes
x86/apic: Deinline __default_send_IPI_*, save ~200 bytes
dt-bindings: interrupt-controller: Add SoC-specific compatible string to Marvell ODMI
irqchip/mips-gic: Add new DT property to reserve IPIs
MIPS: Delete smp-gic.c
MIPS: Make smp CMP, CPS and MT use the new generic IPI functions
MIPS: Add generic SMP IPI support
...
Pull timer updates from Thomas Gleixner:
"The timer department delivers this time:
- Support for cross clock domain timestamps in the core code plus a
first user. That allows more precise timestamping for PTP and
later for audio and other peripherals.
The ptp/e1000e patches have been acked by the relevant maintainers
and are carried in the timer tree to avoid merge ordering issues.
- Support for unregistering the current clocksource watchdog. That
lifts a limitation for switching clocksources which has been there
from day 1
- The usual pile of fixes and updates to the core and the drivers.
Nothing outstanding and exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
time/timekeeping: Work around false positive GCC warning
e1000e: Adds hardware supported cross timestamp on e1000e nic
ptp: Add PTP_SYS_OFFSET_PRECISE for driver crosstimestamping
x86/tsc: Always Running Timer (ART) correlated clocksource
hrtimer: Revert CLOCK_MONOTONIC_RAW support
time: Add history to cross timestamp interface supporting slower devices
time: Add driver cross timestamp interface for higher precision time synchronization
time: Remove duplicated code in ktime_get_raw_and_real()
time: Add timekeeping snapshot code capturing system time and counter
time: Add cycles to nanoseconds translation
jiffies: Use CLOCKSOURCE_MASK instead of constant
clocksource: Introduce clocksource_freq2mult()
clockevents/drivers/exynos_mct: Implement ->set_state_oneshot_stopped()
clockevents/drivers/arm_global_timer: Implement ->set_state_oneshot_stopped()
clockevents/drivers/arm_arch_timer: Implement ->set_state_oneshot_stopped()
clocksource/drivers/arm_global_timer: Register delay timer
clocksource/drivers/lpc32xx: Support timer-based ARM delay
clocksource/drivers/lpc32xx: Support periodic mode
clocksource/drivers/lpc32xx: Don't use the prescaler counter for clockevents
clocksource/drivers/rockchip: Add err handle for rk_timer_init
...
Pull x86 timer update from Ingo Molnar:
"A single simplification of the x86 TSC code"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Use topology functions
Pull x86 core platform updates from Ingo Molnar:
"Intel Quark and Geode SoC platform updates"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/intel/quark: Drop IMR lock bit support
x86/platform/intel/mid: Remove dead code
x86/platform: Make platform/geode/net5501.c explicitly non-modular
x86/platform: Make platform/geode/alix.c explicitly non-modular
x86/platform: Make platform/geode/geos.c explicitly non-modular
x86/platform: Make platform/intel-quark/imr_selftest.c explicitly non-modular
x86/platform: Make platform/intel-quark/imr.c explicitly non-modular
Pull x86 mm updates from Ingo Molnar:
"The main changes in this cycle were:
- Enable full ASLR randomization for 32-bit programs (Hector
Marco-Gisbert)
- Add initial minimal INVPCI support, to flush global mappings (Andy
Lutomirski)
- Add KASAN enhancements (Andrey Ryabinin)
- Fix mmiotrace for huge pages (Karol Herbst)
- ... misc cleanups and small enhancements"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/32: Enable full randomization on i386 and X86_32
x86/mm/kmmio: Fix mmiotrace for hugepages
x86/mm: Avoid premature success when changing page attributes
x86/mm/ptdump: Remove paravirt_enabled()
x86/mm: Fix INVPCID asm constraint
x86/dmi: Switch dmi_remap() from ioremap() [uncached] to ioremap_cache()
x86/mm: If INVPCID is available, use it to flush global mappings
x86/mm: Add a 'noinvpcid' boot option to turn off INVPCID
x86/mm: Add INVPCID helpers
x86/kasan: Write protect kasan zero shadow
x86/kasan: Clear kasan_zero_page after TLB flush
x86/mm/numa: Check for failures in numa_clear_kernel_node_hotplug()
x86/mm/numa: Clean up numa_clear_kernel_node_hotplug()
x86/mm: Make kmap_prot into a #define
x86/mm/32: Set NX in __supported_pte_mask before enabling paging
x86/mm: Streamline and restore probe_memory_block_size()
Pull x86 microcode updates from Ingo Molnar:
"The biggest change in this cycle was the separation of the microcode
loading mechanism from the initrd code plus the support of built-in
microcode images.
There were also lots cleanups and general restructuring (by Borislav
Petkov)"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/microcode/intel: Drop orig_sum from ext signature checksum
x86/microcode/intel: Improve microcode sanity-checking error messages
x86/microcode/intel: Merge two consecutive if-statements
x86/microcode/intel: Get rid of DWSIZE
x86/microcode/intel: Change checksum variables to u32
x86/microcode: Use kmemdup() rather than duplicating its implementation
x86/microcode: Remove unnecessary paravirt_enabled check
x86/microcode: Document builtin microcode loading method
x86/microcode/AMD: Issue microcode updated message later
x86/microcode/intel: Cleanup get_matching_model_microcode()
x86/microcode/intel: Remove unused arg of get_matching_model_microcode()
x86/microcode/intel: Rename mc_saved_in_initrd
x86/microcode/intel: Use *wrmsrl variants
x86/microcode/intel: Cleanup apply_microcode_intel()
x86/microcode/intel: Move the BUG_ON up and turn it into WARN_ON
x86/microcode/intel: Rename mc_intel variable to mc
x86/microcode/intel: Rename mc_saved_count to num_saved
x86/microcode/intel: Rename local variables of type struct mc_saved_data
x86/microcode/AMD: Drop redundant printk prefix
x86/microcode: Issue update message only once
...
Pull x86 fpu updates from Ingo Molnar:
"The biggest change in terms of impact is the changing of the FPU
context switch model to 'eagerfpu' for all CPU types, via: commit
58122bf1d8: "x86/fpu: Default eagerfpu=on on all CPUs"
This makes all FPU saves and restores synchronous and makes the FPU
code a lot more obvious to read. In the next cycle, if this change is
problem free, we'll remove the old lazy FPU restore code altogether.
This change flushed out some old bugs, which should all be fixed by
now, BYMMV"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Default eagerfpu=on on all CPUs
x86/fpu: Speed up lazy FPU restores slightly
x86/fpu: Fold fpu_copy() into fpu__copy()
x86/fpu: Fix FNSAVE usage in eagerfpu mode
x86/fpu: Fix math emulation in eager fpu mode
Pull x86 build update from Ingo Molnar:
"A single adjustment of a defconfig value"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/defconfigs/32: Set CONFIG_FRAME_WARN to the Kconfig default
Pull x86 boot updates from Ingo Molnar:
"Early command line options parsing enhancements from Dave Hansen, plus
minor cleanups and enhancements"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Remove unused 'is_big_kernel' variable
x86/boot: Use proper array element type in memset() size calculation
x86/boot: Pass in size to early cmdline parsing
x86/boot: Simplify early command line parsing
x86/boot: Fix early command-line parsing when partial word matches
x86/boot: Fix early command-line parsing when matching at end
x86/boot: Simplify kernel load address alignment check
x86/boot: Micro-optimize reset_early_page_tables()
Pull x86 asm updates from Ingo Molnar:
"This is another big update. Main changes are:
- lots of x86 system call (and other traps/exceptions) entry code
enhancements. In particular the complex parts of the 64-bit entry
code have been migrated to C code as well, and a number of dusty
corners have been refreshed. (Andy Lutomirski)
- vDSO special mapping robustification and general cleanups (Andy
Lutomirski)
- cpufeature refactoring, cleanups and speedups (Borislav Petkov)
- lots of other changes ..."
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
x86/cpufeature: Enable new AVX-512 features
x86/entry/traps: Show unhandled signal for i386 in do_trap()
x86/entry: Call enter_from_user_mode() with IRQs off
x86/entry/32: Change INT80 to be an interrupt gate
x86/entry: Improve system call entry comments
x86/entry: Remove TIF_SINGLESTEP entry work
x86/entry/32: Add and check a stack canary for the SYSENTER stack
x86/entry/32: Simplify and fix up the SYSENTER stack #DB/NMI fixup
x86/entry: Only allocate space for tss_struct::SYSENTER_stack if needed
x86/entry: Vastly simplify SYSENTER TF (single-step) handling
x86/entry/traps: Clear DR6 early in do_debug() and improve the comment
x86/entry/traps: Clear TIF_BLOCKSTEP on all debug exceptions
x86/entry/32: Restore FLAGS on SYSEXIT
x86/entry/32: Filter NT and speed up AC filtering in SYSENTER
x86/entry/compat: In SYSENTER, sink AC clearing below the existing FLAGS test
selftests/x86: In syscall_nt, test NT|TF as well
x86/asm-offsets: Remove PARAVIRT_enabled
x86/entry/32: Introduce and use X86_BUG_ESPFIX instead of paravirt_enabled
uprobes: __create_xol_area() must nullify xol_mapping.fault
x86/cpufeature: Create a new synthetic cpu capability for machine check recovery
...
Pull NOHZ updates from Ingo Molnar:
"NOHZ enhancements, by Frederic Weisbecker, which reorganizes/refactors
the NOHZ 'can the tick be stopped?' infrastructure and related code to
be data driven, and harmonizes the naming and handling of all the
various properties"
[ This makes the ugly "fetch_or()" macro that the scheduler used
internally a new generic helper, and does a bad job at it.
I'm pulling it, but I've asked Ingo and Frederic to get this
fixed up ]
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched-clock: Migrate to use new tick dependency mask model
posix-cpu-timers: Migrate to use new tick dependency mask model
sched: Migrate sched to use new tick dependency mask model
sched: Account rr tasks
perf: Migrate perf to use new tick dependency mask model
nohz: Use enum code for tick stop failure tracing message
nohz: New tick dependency mask
nohz: Implement wide kick on top of irq work
atomic: Export fetch_or()
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- Make schedstats a runtime tunable (disabled by default) and
optimize it via static keys.
As most distributions enable CONFIG_SCHEDSTATS=y due to its
instrumentation value, this is a nice performance enhancement.
(Mel Gorman)
- Implement 'simple waitqueues' (swait): these are just pure
waitqueues without any of the more complex features of full-blown
waitqueues (callbacks, wake flags, wake keys, etc.). Simple
waitqueues have less memory overhead and are faster.
Use simple waitqueues in the RCU code (in 4 different places) and
for handling KVM vCPU wakeups.
(Peter Zijlstra, Daniel Wagner, Thomas Gleixner, Paul Gortmaker,
Marcelo Tosatti)
- sched/numa enhancements (Rik van Riel)
- NOHZ performance enhancements (Rik van Riel)
- Various sched/deadline enhancements (Steven Rostedt)
- Various fixes (Peter Zijlstra)
- ... and a number of other fixes, cleanups and smaller enhancements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
sched/cputime: Fix steal_account_process_tick() to always return jiffies
sched/deadline: Remove dl_new from struct sched_dl_entity
Revert "kbuild: Add option to turn incompatible pointer check into error"
sched/deadline: Remove superfluous call to switched_to_dl()
sched/debug: Fix preempt_disable_ip recording for preempt_disable()
sched, time: Switch VIRT_CPU_ACCOUNTING_GEN to jiffy granularity
time, acct: Drop irq save & restore from __acct_update_integrals()
acct, time: Change indentation in __acct_update_integrals()
sched, time: Remove non-power-of-two divides from __acct_update_integrals()
sched/rt: Kick RT bandwidth timer immediately on start up
sched/debug: Add deadline scheduler bandwidth ratio to /proc/sched_debug
sched/debug: Move sched_domain_sysctl to debug.c
sched/debug: Move the /sys/kernel/debug/sched_features file setup into debug.c
sched/rt: Fix PI handling vs. sched_setscheduler()
sched/core: Remove duplicated sched_group_set_shares() prototype
sched/fair: Consolidate nohz CPU load update code
sched/fair: Avoid using decay_load_missed() with a negative value
sched/deadline: Always calculate end of period on sched_yield()
sched/cgroup: Fix cgroup entity load tracking tear-down
rcu: Use simple wait queues where possible in rcutree
...
Pull RAS updates from Ingo Molnar:
"Various RAS updates:
- AMD MCE support updates for future CPUs, fixes and 'SMCA' (Scalable
MCA) error decoding support (Aravind Gopalakrishnan)
- x86 memcpy_mcsafe() support, to enable smart(er) hardware error
recovery in NVDIMM drivers, based on an extension of the x86
exception handling code. (Tony Luck)"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
EDAC/sb_edac: Fix computation of channel address
x86/mm, x86/mce: Add memcpy_mcsafe()
x86/mce/AMD: Document some functionality
x86/mce: Clarify comments regarding deferred error
x86/mce/AMD: Fix logic to obtain block address
x86/mce/AMD, EDAC: Enable error decoding of Scalable MCA errors
x86/mce: Move MCx_CONFIG MSR definitions
x86/mce: Check for faults tagged in EXTABLE_CLASS_FAULT exception table entries
x86/mm: Expand the exception table logic to allow new handling options
x86/mce/AMD: Set MCAX Enable bit
x86/mce/AMD: Carve out threshold block preparation
x86/mce/AMD: Fix LVT offset configuration for thresholding
x86/mce/AMD: Reduce number of blocks scanned per bank
x86/mce/AMD: Do not perform shared bank check for future processors
x86/mce: Fix order of AMD MCE init function call
Pull perf updates from Ingo Molnar:
"Main kernel side changes:
- Big reorganization of the x86 perf support code. The old code grew
organically deep inside arch/x86/kernel/cpu/perf* and its naming
became somewhat messy.
The new location is under arch/x86/events/, using the following
cleaner hierarchy of source code files:
perf/x86: Move perf_event.c .................. => x86/events/core.c
perf/x86: Move perf_event_amd.c .............. => x86/events/amd/core.c
perf/x86: Move perf_event_amd_ibs.c .......... => x86/events/amd/ibs.c
perf/x86: Move perf_event_amd_iommu.[ch] ..... => x86/events/amd/iommu.[ch]
perf/x86: Move perf_event_amd_uncore.c ....... => x86/events/amd/uncore.c
perf/x86: Move perf_event_intel_bts.c ........ => x86/events/intel/bts.c
perf/x86: Move perf_event_intel.c ............ => x86/events/intel/core.c
perf/x86: Move perf_event_intel_cqm.c ........ => x86/events/intel/cqm.c
perf/x86: Move perf_event_intel_cstate.c ..... => x86/events/intel/cstate.c
perf/x86: Move perf_event_intel_ds.c ......... => x86/events/intel/ds.c
perf/x86: Move perf_event_intel_lbr.c ........ => x86/events/intel/lbr.c
perf/x86: Move perf_event_intel_pt.[ch] ...... => x86/events/intel/pt.[ch]
perf/x86: Move perf_event_intel_rapl.c ....... => x86/events/intel/rapl.c
perf/x86: Move perf_event_intel_uncore.[ch] .. => x86/events/intel/uncore.[ch]
perf/x86: Move perf_event_intel_uncore_nhmex.c => x86/events/intel/uncore_nmhex.c
perf/x86: Move perf_event_intel_uncore_snb.c => x86/events/intel/uncore_snb.c
perf/x86: Move perf_event_intel_uncore_snbep.c => x86/events/intel/uncore_snbep.c
perf/x86: Move perf_event_knc.c .............. => x86/events/intel/knc.c
perf/x86: Move perf_event_p4.c ............... => x86/events/intel/p4.c
perf/x86: Move perf_event_p6.c ............... => x86/events/intel/p6.c
perf/x86: Move perf_event_msr.c .............. => x86/events/msr.c
(Borislav Petkov)
- Update various x86 PMU constraint and hw support details (Stephane
Eranian)
- Optimize kprobes for BPF execution (Martin KaFai Lau)
- Rewrite, refactor and fix the Intel uncore PMU driver code (Thomas
Gleixner)
- Rewrite, refactor and fix the Intel RAPL PMU code (Thomas Gleixner)
- Various fixes and smaller cleanups.
There are lots of perf tooling updates as well. A few highlights:
perf report/top:
- Hierarchy histogram mode for 'perf top' and 'perf report',
showing multiple levels, one per --sort entry: (Namhyung Kim)
On a mostly idle system:
# perf top --hierarchy -s comm,dso
Then expand some levels and use 'P' to take a snapshot:
# cat perf.hist.0
- 92.32% perf
58.20% perf
22.29% libc-2.22.so
5.97% [kernel]
4.18% libelf-0.165.so
1.69% [unknown]
- 4.71% qemu-system-x86
3.10% [kernel]
1.60% qemu-system-x86_64 (deleted)
+ 2.97% swapper
#
- Add 'L' hotkey to dynamicly set the percent threshold for
histogram entries and callchains, i.e. dynamicly do what the
--percent-limit command line option to 'top' and 'report' does.
(Namhyung Kim)
perf mem:
- Allow specifying events via -e in 'perf mem record', also listing
what events can be specified via 'perf mem record -e list' (Jiri
Olsa)
perf record:
- Add 'perf record' --all-user/--all-kernel options, so that one
can tell that all the events in the command line should be
restricted to the user or kernel levels (Jiri Olsa), i.e.:
perf record -e cycles:u,instructions:u
is equivalent to:
perf record --all-user -e cycles,instructions
- Make 'perf record' collect CPU cache info in the perf.data file header:
$ perf record usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.017 MB perf.data (7 samples) ]
$ perf report --header-only -I | tail -10 | head -8
# CPU cache info:
# L1 Data 32K [0-1]
# L1 Instruction 32K [0-1]
# L1 Data 32K [2-3]
# L1 Instruction 32K [2-3]
# L2 Unified 256K [0-1]
# L2 Unified 256K [2-3]
# L3 Unified 4096K [0-3]
Will be used in 'perf c2c' and eventually in 'perf diff' to
allow, for instance running the same workload in multiple
machines and then when using 'diff' show the hardware difference.
(Jiri Olsa)
- Improved support for Java, using the JVMTI agent library to do
jitdumps that then will be inserted in synthesized
PERF_RECORD_MMAP2 events via 'perf inject' pointed to synthesized
ELF files stored in ~/.debug and keyed with build-ids, to allow
symbol resolution and even annotation with source line info, see
the changeset comments to see how to use it (Stephane Eranian)
perf script/trace:
- Decode data_src values (e.g. perf.data files generated by 'perf
mem record') in 'perf script': (Jiri Olsa)
# perf script
perf 693 [1] 4.088652: 1 cpu/mem-loads,ldlat=30/P: ffff88007d0b0f40 68100142 L1 hit|SNP None|TLB L1 or L2 hit|LCK No <SNIP>
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
- Improve support to 'data_src', 'weight' and 'addr' fields in
'perf script' (Jiri Olsa)
- Handle empty print fmts in 'perf script -s' i.e. when running
python or perl scripts (Taeung Song)
perf stat:
- 'perf stat' now shows shadow metrics (insn per cycle, etc) in
interval mode too. E.g:
# perf stat -I 1000 -e instructions,cycles sleep 1
# time counts unit events
1.000215928 519,620 instructions # 0.69 insn per cycle
1.000215928 752,003 cycles
<SNIP>
- Port 'perf kvm stat' to PowerPC (Hemant Kumar)
- Implement CSV metrics output in 'perf stat' (Andi Kleen)
perf BPF support:
- Support converting data from bpf events in 'perf data' (Wang Nan)
- Print bpf-output events in 'perf script': (Wang Nan).
# perf record -e bpf-output/no-inherit,name=evt/ -e ./test_bpf_output_3.c/map:channel.event=evt/ usleep 1000
# perf script
usleep 4882 21384.532523: evt: ffffffff810e97d1 sys_nanosleep ([kernel.kallsyms])
BPF output: 0000: 52 61 69 73 65 20 61 20 Raise a
0008: 42 50 46 20 65 76 65 6e BPF even
0010: 74 21 00 00 t!..
BPF string: "Raise a BPF event!"
#
- Add API to set values of map entries in a BPF object, be it
individual map slots or ranges (Wang Nan)
- Introduce support for the 'bpf-output' event (Wang Nan)
- Add glue to read perf events in a BPF program (Wang Nan)
- Improve support for bpf-output events in 'perf trace' (Wang Nan)
... and tons of other changes as well - see the shortlog and git log
for details!"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (342 commits)
perf stat: Add --metric-only support for -A
perf stat: Implement --metric-only mode
perf stat: Document CSV format in manpage
perf hists browser: Check sort keys before hot key actions
perf hists browser: Allow thread filtering for comm sort key
perf tools: Add sort__has_comm variable
perf tools: Recalc total periods using top-level entries in hierarchy
perf tools: Remove nr_sort_keys field
perf hists browser: Cleanup hist_browser__fprintf_hierarchy_entry()
perf tools: Remove hist_entry->fmt field
perf tools: Fix command line filters in hierarchy mode
perf tools: Add more sort entry check functions
perf tools: Fix hist_entry__filter() for hierarchy
perf jitdump: Build only on supported archs
tools lib traceevent: Add '~' operation within arg_num_eval()
perf tools: Omit unnecessary cast in perf_pmu__parse_scale
perf tools: Pass perf_hpp_list all the way through setup_sort_list
perf tools: Fix perf script python database export crash
perf jitdump: DWARF is also needed
perf bench mem: Prepare the x86-64 build for upstream memcpy_mcsafe() changes
...
Pull read-only kernel memory updates from Ingo Molnar:
"This tree adds two (security related) enhancements to the kernel's
handling of read-only kernel memory:
- extend read-only kernel memory to a new class of formerly writable
kernel data: 'post-init read-only memory' via the __ro_after_init
attribute, and mark the ARM and x86 vDSO as such read-only memory.
This kind of attribute can be used for data that requires a once
per bootup initialization sequence, but is otherwise never modified
after that point.
This feature was based on the work by PaX Team and Brad Spengler.
(by Kees Cook, the ARM vDSO bits by David Brown.)
- make CONFIG_DEBUG_RODATA always enabled on x86 and remove the
Kconfig option. This simplifies the kernel and also signals that
read-only memory is the default model and a first-class citizen.
(Kees Cook)"
* 'mm-readonly-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/vdso: Mark the vDSO code read-only after init
x86/vdso: Mark the vDSO code read-only after init
lkdtm: Verify that '__ro_after_init' works correctly
arch: Introduce post-init read-only memory
x86/mm: Always enable CONFIG_DEBUG_RODATA and remove the Kconfig option
mm/init: Add 'rodata=off' boot cmdline parameter to disable read-only kernel mappings
asm-generic: Consolidate mark_rodata_ro()
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()
Pull locking changes from Ingo Molnar:
"Various updates:
- Futex scalability improvements: remove page lock use for shared
futex get_futex_key(), which speeds up 'perf bench futex hash'
benchmarks by over 40% on a 60-core Westmere. This makes anon-mem
shared futexes perform close to private futexes. (Mel Gorman)
- lockdep hash collision detection and fix (Alfredo Alvarez
Fernandez)
- lockdep testing enhancements (Alfredo Alvarez Fernandez)
- robustify lockdep init by using hlists (Andrew Morton, Andrey
Ryabinin)
- mutex and csd_lock micro-optimizations (Davidlohr Bueso)
- small x86 barriers tweaks (Michael S Tsirkin)
- qspinlock updates (Waiman Long)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
locking/csd_lock: Use smp_cond_acquire() in csd_lock_wait()
locking/csd_lock: Explicitly inline csd_lock*() helpers
futex: Replace barrier() in unqueue_me() with READ_ONCE()
locking/lockdep: Detect chain_key collisions
locking/lockdep: Prevent chain_key collisions
tools/lib/lockdep: Fix link creation warning
tools/lib/lockdep: Add tests for AA and ABBA locking
tools/lib/lockdep: Add userspace version of READ_ONCE()
tools/lib/lockdep: Fix the build on recent kernels
locking/qspinlock: Move __ARCH_SPIN_LOCK_UNLOCKED to qspinlock_types.h
locking/mutex: Allow next waiter lockless wakeup
locking/pvqspinlock: Enable slowpath locking count tracking
locking/qspinlock: Use smp_cond_acquire() in pending code
locking/pvqspinlock: Move lock stealing count tracking code into pv_queued_spin_steal_lock()
locking/mcs: Fix mcs_spin_lock() ordering
futex: Remove requirement for lock_page() in get_futex_key()
futex: Rename barrier references in ordering guarantees
locking/atomics: Update comment about READ_ONCE() and structures
locking/lockdep: Eliminate lockdep_init()
locking/lockdep: Convert hash tables to hlists
...
Pull ram resource handling changes from Ingo Molnar:
"Core kernel resource handling changes to support NVDIMM error
injection.
This tree introduces a new I/O resource type, IORESOURCE_SYSTEM_RAM,
for System RAM while keeping the current IORESOURCE_MEM type bit set
for all memory-mapped ranges (including System RAM) for backward
compatibility.
With this resource flag it no longer takes a strcmp() loop through the
resource tree to find "System RAM" resources.
The new resource type is then used to extend ACPI/APEI error injection
facility to also support NVDIMM"
* 'core-resources-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ACPI/EINJ: Allow memory error injection to NVDIMM
resource: Kill walk_iomem_res()
x86/kexec: Remove walk_iomem_res() call with GART type
x86, kexec, nvdimm: Use walk_iomem_res_desc() for iomem search
resource: Add walk_iomem_res_desc()
memremap: Change region_intersects() to take @flags and @desc
arm/samsung: Change s3c_pm_run_res() to use System RAM type
resource: Change walk_system_ram() to use System RAM type
drivers: Initialize resource entry to zero
xen, mm: Set IORESOURCE_SYSTEM_RAM to System RAM
kexec: Set IORESOURCE_SYSTEM_RAM for System RAM
arch: Set IORESOURCE_SYSTEM_RAM flag for System RAM
ia64: Set System RAM type and descriptor
x86/e820: Set System RAM type and descriptor
resource: Add I/O resource descriptor
resource: Handle resource flags properly
resource: Add System RAM resource type
There are only a few differences between PCF2127 and PCF2129 (PCF2127
has 512 bytes of general purpose SRAM and count-down timer).
The rtc-pcf2127 driver currently doesn't use the PCF2127 specific
functionality and Kconfig help text already says this driver supports
PCF2127/29, so we can simply add pcf2129 to device id list.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2127 has selectable I2C-bus and SPI-bus interface support.
This adds support for SPI interface.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2127 has selectable I2C-bus and SPI-bus interface support.
Currently rtc-pcf2127 driver only supports I2C.
This is preparation for support for SPI interface.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support to
- enable/disable the thermometer
- set the temperature scanning interval
- read the current temperature that is used for temp compensation.
via hwmon interface
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This simplifies the update of single bits in the eeprom.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
objtool reports the following warnings:
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_work_queue()+0x0: duplicate frame pointer save
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_work_queue()+0x3: duplicate frame pointer setup
drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_work_queue()+0x0: frame pointer state mismatch
The warning message needs to be improved, but what it really means in
this case is that ds1685_rtc_poweroff() has a possible code path where
it can actually fall through to the next function in the object code,
ds1685_rtc_work_queue().
The bug is caused by the use of the unreachable() macro in a place which
is actually reachable. That causes gcc to assume that the printk()
immediately before the unreachable() macro never returns, when in fact
it does. So gcc places the printk() at the very end of the function's
object code. When the printk() returns, the next function starts
executing.
The surrounding comment and printk message state that the code should
spin forever, which explains the unreachable() statement. However the
actual spin code is missing.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Year field must be in BCD format, according to
hym8563 datasheet.
Due to the bug year 2016 became 2010.
Fixes: dcaf038493 ("rtc: add hym8563 rtc-driver")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds3232->mutex is used to protect for alarm operations which
need to access status and control registers.
But we can use rtc->ops_lock instead. rtc->ops_lock is held when most
of rtc_class_ops methods are called, so we only need to explicitly
acquire it from irq handler in order to protect form concurrent
accesses.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ds3232-core requests irq with IRQF_SHARED, so irq can be shared by
several devices. But the irq handler for ds3232 unconditionally
disables the irq at first and the irq is re-enabled only when the
interrupt source was the ds3232's alarm. This behaviour breaks the
devices sharing the same irq in the various scenarios.
This converts to use threaded irq and remove outdated code in
suspend/resume paths.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
UIE mode irqs are handled by the generic rtc core now. But there are
remaining unused code fragments for it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add missing register access error checks and make it return error code
or print error message.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rtctest (tools/testing/selftests/timers/rtctest.c) found that
reading ds3232 rtc device immediately return the value 0x20 (RTC_AF)
without waiting alarm interrupt.
This is because alarm_irq_enable() of ds3232 driver changes RTC_AF
flag in rtc->irq_data. So calling ioctl with RTC_AIE_ON generates
invalid value in rtc device.
The lower-level driver should not touch rtc->irq_data directly.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to "Feature Comparison of the DS323x Real-Time Clocks"
(http://pdfserv.maximintegrated.com/en/an/AN5143.pdf), DS3232 and
DS3234 are very similar.
This merges rtc-ds3232 and rtc-ds3234 with using regmap.
This change also enables to support alarm for ds3234.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The trickle charger resistor can be enabled via device tree
property trickle-resistor-ohms.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds functions for access to the EEPROM memory on the rv3029.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds all (according to the data sheet) missing register and bit
definitions.
It also fixes the definition of the trickle charger bit masks.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The C2 suffix does not appear in the latest datasheet, so add
a device ID without it.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The C2 suffix does not appear anymore in the latest device and
data sheet versions.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There are several arch-specific RTC drivers that can be successfully
compiled on other platforms. Add a COMPILE_TEST dependency for those.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
There are four architectures using this driver, but since we can
build it with COMPILE_TEST, we should try dealing with the absence
of the asm/rtc.h header file, to avoid getting a build error:
drivers/rtc/rtc-generic.c:12:21: fatal error: asm/rtc.h: No such file or directory
This creates an alternative use of the driver, allowing architectures
to pass a set of rtc_class_ops in platform data. We can convert the
four architectures to use this and then remove the original
code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The time and date register of the pcf8223 are undefined after a power
reset. Properly handle the OS bit and return -EINVAL when that bit is set.
It is properly removed when setting the time.
This solves an issue where the time and date may be valid for
rtc_valid_tm() but is not the current time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
No members of struct pcf85063 are used anymore, remove the whole structure.
Reviewed-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We call spin_lock_irqrestore with "flags" set to zero instead of to the
value from spin_lock_irqsave().
Fixes: aaaf5fbf56 ('rtc: add driver for DS1685 family of real time clocks')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
