When running in HDMI mode, the sor1 IP block needs to use the sor1_src
as parent clock, and in turn configure the sor1_src to use pll_d2_out0
as its parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR clock can have various sources, with the most commonly used
being the sor_safe, pll_d2_out0, pll_dp and sor_brick clocks. These
are configured using a three level mux, of which the first 2 levels
can be treated as one. The direct parents of the SOR clock are the
sor_safe, sor_brick and sor_src clocks, whereas the pll_d2_out0 and
pll_dp clocks can be selected as parents of the sor_src clock via a
second mux.
Previous generations of Tegra have only supported eDP and LVDS with
the SOR, where LVDS was never used on publicly available hardware.
Clocking for this only ever required the first level mux (to select
between sor_safe and sor_brick).
Tegra210 has a new revision of the SOR that supports HDMI and hence
needs to support the second level mux to allow selecting pll_d2_out0
as the SOR clock's parent. This second mux is knows as sor_src, and
operating system software needs a reference to it in order to select
the proper parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
sor1_brick is a clock that can be used as a source for the sor1 clock.
The registers to control the clock output are part of the sor1 IP block
and hence the sor driver is the best place to implement it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, we completely ignore the user when it comes to the in/out
direction of the ioctl argument, as we simply cannot trust userspace.
(For example, they might request a copy of the modified ioctl argument
when the driver is not expecting such and so leak kernel stack.)
However, blindly copying over the target address may also lead to a
spurious EFAULT, and a failure after the ioctl was completed
successfully. This is important in order to avoid an ABI break when
extending an ioctl from IOR to IORW. Similar to how we only copy the
intersection of the kernel arg size and the user arg size, we only want
to copy back the kernel arg data iff both the kernel and userspace
request the copy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1468335590-21023-1-git-send-email-chris@chris-wilson.co.uk
Here's an initial drm-next pull for nouveau 4.8, highlights:
- GK20A/GM20B volt and clock improvements.
- Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
* 'linux-4.8' of git://github.com/skeggsb/linux: (97 commits)
drm/nouveau/bus: remove cpu_coherent flag
drm/nouveau/ttm: remove special handling of coherent objects
drm/nouveau: check for supported chipset before booting fbdev off the hw
drm/nouveau/ce/gp104: initial support
drm/nouveau/fifo/gp104: initial support
drm/nouveau/disp/gp104: initial support
drm/nouveau/dma/gp104: initial support
drm/nouveau/ltc/gp104: initial support
drm/nouveau/ibus/gp104: initial support
drm/nouveau/i2c/gp104: initial support
drm/nouveau/gpio/gp104: initial support
drm/nouveau/fuse/gp104: initial support
drm/nouveau/bus/gp104: initial support
drm/nouveau/bar/gp104: initial support
drm/nouveau/mmu/gp104: initial support
drm/nouveau/fb/gp104: initial support
drm/nouveau/imem/gp104: initial support
drm/nouveau/devinit/gp104: initial support
drm/nouveau/bios/gp104: initial support
drm/nouveau/tmr/gp104: initial support
...
This flag's only remaining function is to ignore the uncached flag for
BOs on coherent architectures.
However the reason for allocating an object uncache on a non-coherent
architecture (namely because the cost of doing explicit flushes/
invalidations is higher than the benefit of caching the data because
accesses are few and far between) should also apply on architectures for
which coherency is maintained implicitly. Thus allocate coherent objects
as uncached on all architectures.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
TTM-allocated coherent objects were populated using the DMA API and
accessed using the mapping it returned to workaround coherency
issues. These issues seem to have been solved, thus remove this extra
case to handle and use the regular kernel mapping functions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Due to the GPU preventing us from touching NV_PLTCG_LTCS_LTSS_CBC_BASE,
we cannot provide CBC/ZBC support without signed PMU firmware to handle
the task for us...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GP100 still supports the previous generations' page table layout, which
we will temporarily make use of here.
Proper support for the new MMU layout requires some rework to the common
MMU code, which is in progress.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
