Compiling for the m68knommu/68328 Palm/Pilot target you get:
AS arch/m68k/platform/68328/head-pilot.o
arch/m68k/platform/68328/head-pilot.S:37:23: fatal error: bootlogo.rh: No such file or directory
The build for this target used to do a conversion on a C coded boot logo
and include this in the head assembler code. This got broken by changes to
the local Makefile.
Clean all this up by just including the C coded boot logo struct in the
C code. With the appropriate alignment attribute there is no difference
to the way it can be used.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In some of the rt6_bind_neighbour() call sites, it hasn't hooked
up the rt->dst.dev pointer yet, so we'd deref a NULL pointer when
obtaining dev->ifindex for the neighbour hash function computation.
Just pass the netdevice explicitly in to fix this problem.
Reported-by: Bjarke Istrup Pedersen <gurligebis@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use _AC() in definition of PAGE_SIZE so the same definition
can be used in C and assembler.
Also use PAGE_SIZE in definition of THREAD_SIZE.
This commit kill the following comment:
"I have my suspicions... -DaveM"
I did not find any clue what this referred to anyway.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While chasing following warning from kconfig I noticed that the
kconfig preemption model symbols were all dependent on sparc64.
warning: (PREEMPT && DEBUG_ATOMIC_SLEEP) selects PREEMPT_COUNT which has unmet direct dependencies (SPARC64)
>From arch/sparc/Kconfig:
if SPARC64
source "kernel/Kconfig.preempt"
endif
But looking a bit closer I see nothing obvious why
sparc32 should not support the various preemption models.
Drop the "if SPARC64" conditional to enable selection of
preemption model on sparc32 too.
Build-tested - but not run-time tested all three models.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin also noticed that we could run the refill work
multiple CPUs: if we kick off a refill on one CPU and then on another,
they would both manipulate the queue at the same time (they use
napi_disable to avoid racing against the receive handler itself).
Tejun points out that this is what the WQ_NON_REENTRANT flag is for,
and that there is a convenient system kthread we can use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin noticed that we could run the refill work after
ndo_close, which can re-enable napi - we don't disable it until
virtnet_remove. This is clearly wrong, so move the workqueue control
to ndo_open and ndo_stop (aka. virtnet_open and virtnet_close).
One subtle point: virtnet_probe() could simply fail if it couldn't
allocate a receive buffer, but that's less polite in virtnet_open() so
we schedule a refill as we do in the normal receive path if we run out
of memory.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment VFs can only operate in Eth mode.
In addition we don't want the VF to attempt link sensing,
so we block this option as well.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: (NETFILTER_XT_MATCH_NFACCT) selects NETFILTER_NETLINK_ACCT which has
unmet direct dependencies (NET && INET && NETFILTER && NETFILTER_ADVANCED)
and then
ERROR: "nfnetlink_subsys_unregister" [net/netfilter/nfnetlink_acct.ko] undefined!
ERROR: "nfnetlink_subsys_register" [net/netfilter/nfnetlink_acct.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing wrong register offset which is used to retrieve the number of buttons
attached to the hardware.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ceph attempts to use the dcache to satisfy negative lookups and readdir
when the entire directory contents are in cache. Disable this behavior
until lingering bugs in this code are shaken out; we'll re-enable these
hooks once things are fully stable.
Signed-off-by: Sage Weil <sage@newdream.net>
Commit 5e081591 "block: warn if tag is greater than real_max_depth"
cleaned up blk_queue_end_tag() to warn when the tag is truly invalid
(greater than real_max_depth). However, it changed behavior in the tag <
max_depth case to not end the request. Leading to triggering of
BUG_ON(blk_queued_rq(rq)) in the request completion path:
http://marc.info/?l=linux-kernel&m=132204370518629&w=2
In order to allow blk_queue_resize_tags() to shrink the tag space
blk_queue_end_tag() must always complete tags with a value less than
real_max_depth regardless of the current max_depth. The comment about
"handling the shrink case" seems to be what prompted changes in this
space, so remove it and BUG on all invalid tags (made even simpler by
Matthew's suggestion to use an unsigned compare).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Tao Ma <boyu.mt@taobao.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Reported-by: Meelis Roos <mroos@ut.ee>
Reported-by: Ed Nadolski <edmund.nadolski@intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It just obscures that the netdevice pointer and the expires value are
implemented in the dst_entry sub-object of the ipv6 route.
And it makes grepping for dst_entry member uses much harder too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, create and use an rt6_bind_neighbour() in net/ipv6/route.c to
consolidate some common logic.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to perform a proper universal hash on a vector of integers,
we have to use different universal hashes on each vector element.
Which means we need 4 different hash randoms for ipv6.
Signed-off-by: David S. Miller <davem@davemloft.net>
- ATARI_MFPSER, ATARI_MIDI, MULTIFACE_III_TTY, and DN_SERIAL
have no corresponding drivers (anymore),
- Clean up SERIAL_CONSOLE dependencies and help text.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Check setsockopt arguments to avoid overflows and return -EINVAL for
too large arguments.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit be639ac6 ("NET: AX.25: Check ioctl arguments to avoid overflows
further down the road") rejects very large arguments, but doesn't
completely fix overflows on 64-bit systems. Consider the AX25_T2 case.
int opt;
...
if (opt < 1 || opt > ULONG_MAX / HZ) {
res = -EINVAL;
break;
}
ax25->t2 = opt * HZ;
The 32-bit multiplication opt * HZ would overflow before being assigned
to 64-bit ax25->t2. This patch changes "opt" to unsigned long.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing L2TP support, I discovered that the l2tp module is not autoloaded
as are other netlink interfaces. There is because of lack of hook in genetlink to call
request_module and load the module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The route we have here is for the address being added to the interface,
ie. for input packet processing.
Therefore using that route to determine whether an output nexthop gateway
is known and resolved doesn't make any sense.
So, simply remove this test, it never triggered anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.
The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.
On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.
After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DT node may have more than 1 domain associated with it, so make sure
the hwirq number is within range when doing DT translation.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Add empty of_get_node/of_put_node functions for !CONFIG_OF builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds clk_prepare/clk_unprepare for mxs clock api by
renaming the existing non-atomic clk_enable/clk_disable to
clk_prepare/clk_unprepare and adding a pair of dummy
clk_enable/clk_disable. Then with selecting HAVE_CLK_PREPARE for
mxs clock, we can fix the mutex locking warning that has been
reported for a few times.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The commit 40d3e0f (clk: provide prepare/unprepare functions) provides
the config option HAVE_CLK_PREPARE for platforms that have
prepare/unprepare implementation to select. This patch adds the option
into drivers/clk/Kconfig, so that it can be actually selected.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
The patch converts mxs-saif driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Dong Aisheng <b29396@freescale.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The patch converts mxs-auart driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alan Cox <alan@linux.intel.com>
The patch converts flexcan driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
The patch converts mxs-mmc driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Chris Ball <cjb@laptop.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The patch converts mxs-dma driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
It's for migrating to generic clk framework API.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The patch converts mxs platform code to clk_prepare/clk_unprepare
by using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's for migrating to generic clk framework API.
The helper functions help cases clk_enable/clk_disable is used
in non-atomic context.
For example, Call clk_enable in probe and clk_disable in remove.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
* drivers/rtc-sa1100:
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
Now sa1100-rtc can support sa1100/pxa/mmp soc series, then we need
add dummy clock for sa1100-rtc.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since the regmap of rtc on sa1100, pxa and mmp Marvell soc families are
almost the same, so re-arch the rtc-sa1100 to support them.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In rtc generic interface of setting alarm, it will check the alarm time
value valid or not, so rtc_periodic_alarm is redundant, remove it.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These registers are used in old ioctl of UIE and PIE, now they are
emulated by rtc generic code of hrtimer, so it can be removed.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the mioa701 board has a M-Systems DiskOnChip G3 chip, add
it to the platform resources of the board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@atosorigin.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge PXA168, PXXA910 and MMP2 together. Add Haojian as maintainer of
both arch-pxa and arch-mmp. Haojian's git tree is also added.
Update Eric's tree since the original one is obsolte.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Include linux/export.h to fix below build warning:
CC arch/arm/mach-pxa/balloon3.o
arch/arm/mach-pxa/balloon3.c:85: warning: data definition has no type or storage class
arch/arm/mach-pxa/balloon3.c:85: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/mach-pxa/balloon3.c:85: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
