The current default configuration is as follows:
- Invert VSYNC signal (active LOW)
- Invert HSYNC signal (active LOW)
The mode flags allow to specify the required polarity per
mode. Furthermore, none of the current driver settings is
actually a standard polarity.
This patch applies the current driver default polarities as
explicit flags to the display which has been introduced with
the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now
also parses the flags field and applies the configuration
accordingly, by using the following values as standard
polarities: (e.g. when no flags are specified):
- VSYNC signal not inverted (active HIGH)
- HSYNC signal not inverted (active HIGH)
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Fix alpha blending by enabling alpha blending for the whole frame if
a color mode with alpha channel is selected (DRM_FORMAT_ARGB*). Also
support color modes without alpha channel (DRM_FORMAT_XRGB*) by just
not enabling alpha blending on layer level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The state of the interrupt mask register on initialization is
unknown, e.g. U-Boot could already used the DCU. So depending on
the boot loader, the outcome of the interrupt mask register could
be different. A defined state is much more preferable. Also, there
is no value in keeping interrupts enabled which we don't need.
Therefor, mask all interrupts on initialization.
Signed-off-by: Stefan Agner <stefan@agner.ch>
If initialization fails (e.g. due to missing panel node or deferred
probe) make sure to roll-back all operations and return the error
code.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Improve error handling during CRTC initialization. Especially avoid
memory leaks in the primary plane initialization error path.
Signed-off-by: Stefan Agner <stefan@agner.ch>
It is not common to do regmap return value checks, especially not
for memory mapped device. We can rule out most error returns since
the conditions are static and we know they are ok (e.g. offset
aligned to register stride). Also without proper error handling
they are not really valuable for the user. Hence remove most of
them.
The check in the interrupt handler is worth keeping since a
volatile register won't be readable in case register caching is
still enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Since we are using cached registers, we need to specify volatile
registers explicitly to avoid reading their value from the cache.
This allows to read the correct interrupt status in fsl_dcu_drm_irq
and clear the asserted bits only.
Signed-off-by: Stefan Agner <stefan@agner.ch>
For state->fb or state->crtc may be NULL in fsl_dcu_drm_plane_atomic_check
function, if so, return 0.
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Promote myself as new maintainer of the Freescale DCU DRM driver.
Acked-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
By default, not only this driver is enabled on all platforms, but also
generic PM Domains and Multi-Function Devices.
Drop the "default y" to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When I reworked this code, I messed up num rb count.
v2: use hweight32
Reviewed-by: Ken Wang <Qingquing.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.
Fix this by ensuring that the id buffer is cacheline aligned.
This issue is similar to that fixed by Commit 84bda12af3
("libata: align ap->sector_buf").
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 2.6.18
Signed-off-by: Tejun Heo <tj@kernel.org>
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be a log spam when there is no cable plugged. Please refer to
following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351https://bugzilla.kernel.org/show_bug.cgi?id=107421
This issue is caused by runtime power management. When there is no cable
plugged, the driver will be suspend (runtime suspend) by OS and NIC will be
put into the D3 state. During this time, if OS call rtl8169_get_stats64()
to dump tally counter, because NIC is in D3 state, the register value read
by driver will return all 0xff. This will let driver think tally counter
flag is not toggled and then sends the warning message "rtl_counters_cond
== 1 (loop: 1000, delay: 10)" to kernel log.
For fixing this issue, 1.add checking driver's pm runtime status in
rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend
for counter accuracy in runtime suspend.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a maintainer entry for FREESCALE GPMI NAND driver and add myself as a
maintainer.
Signed-off-by: Han Xu <han.xu@nxp.com>
Acked-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
"d1cd121083: x86, pageattr: Prevent overflow in slow_virt_to_phys() for
X86_PAE" was unintentionally removed by the recent "34437e67a6: x86/mm: Fix
slow_virt_to_phys() to handle large PAT bit".
And, the variable 'phys_addr' was defined as "unsigned long" by mistake -- it should
be "phys_addr_t".
As a result, Hyper-V network driver in 32-PAE Linux guest can't work again.
Fixes: commit 34437e67a6: "x86/mm: Fix slow_virt_to_phys() to handle large PAT bit"
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Cc: olaf@aepfle.de
Cc: gregkh@linuxfoundation.org
Cc: jasowang@redhat.com
Cc: driverdev-devel@linuxdriverproject.org
Cc: linux-mm@kvack.org
Cc: apw@canonical.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Link: http://lkml.kernel.org/r/1456394292-9030-1-git-send-email-decui@microsoft.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The AMD Family 15h Models 30h-3Fh (Kaveri) BIOS and Kernel Developer's
Guide omitted part of the BIOS IOMMU L2 register setup specification.
Without this setup the IOMMU L2 does not fully respect write permissions
when handling an ATS translation request.
The IOMMU L2 will set PTE dirty bit when handling an ATS translation with
write permission request, even when PTE RW bit is clear. This may occur by
direct translation (which would cause a PPR) or by prefetch request from
the ATC.
This is observed in practice when the IOMMU L2 modifies a PTE which maps a
pagecache page. The ext4 filesystem driver BUGs when asked to writeback
these (non-modified) pages.
Enable ATS write permission check in the Kaveri IOMMU L2 if BIOS has not.
Signed-off-by: Jay Cornwall <jay@jcornwall.me>
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The setup code for the performance counters in the AMD IOMMU driver
tests whether the counters can be written. It tests to setup a counter
for device 00:00.0, which fails on systems where this particular device
is not covered by the IOMMU.
Fix this by not relying on device 00:00.0 but only on the IOMMU being
present.
Cc: stable@vger.kernel.org
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The R-Car GPIO driver handles Runtime PM for requested GPIOs only.
When using a GPIO purely as an interrupt source, no Runtime PM handling
is done, and the GPIO module's clock may not be enabled.
To fix this:
- Add .irq_request_resources() and .irq_release_resources() callbacks
to handle Runtime PM when an interrupt is requested,
- Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM
when e.g. disabling/enabling an interrupt, or configuring the
interrupt type.
Fixes: d5c3d84657 "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS"
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_kzalloc() and devm_kcalloc() for private data allocation at
driver load time.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Initialize port device node pointer in the tilcdc crtc. Fixes "Falling
back to first CRTC" warning from tda998x driver.
The tda998x encoder driver calls drm_of_find_possible_crtcs() to
initialize possible_crtcs of struct drm_encoder. The crtc->port needs
to be initialized for drm_of_find_possible_crtcs() to work.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Disable the sync lost interrupt if it fires on every frame for 50
consecutive frames in a row. This is relatively sure sign of the sync
lost interrupt being stuck and firing on every frame even if the
display otherwise appears to work OK.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add ratelimited prints on sync lost and FIFO underrun interrupts.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes the duplicate LCDC_INT_ENABLE_SET_REG-entry in registers array.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix interrupt enable/disable code for version 2 tilcdc. In version 2
tilcdc there is a separate register for disabling interrupts. Writing
0 to enable registers bits does not have any effect. The interrupt
clear register works the same way, writing 1 to specific bit disables
the interrupt and writing 0 does not have any effect.
The "bug" that is fixed here does not really do any harm since the
interrupts are enabled only once in the power up and disabled before
power down.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not update the next frame buffer close to vertical blank. This is
to avoid situation when the frame changes between writing of
LCDC_DMA_FB_BASE_ADDR_0_REG and LCDC_DMA_FB_CEILING_ADDR_0_REG.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Get rid of complex ping-pong mechanism and replace it with simpler
single buffer flipping code.
The LCDC HW appears to be designed mainly static framebuffers in
mind. There are two modes of operation, either static single buffer,
or ping pong double buffering with two static buffers switching back
and forth. Luckily the framebuffer start address is fetched only in
the beginning of the frame and changing the address after that only
takes effect after the next vertical blank. The page flipping code can
simply write the address of the new framebuffer and the page is
flipped automatically after the next vertical blank. Using the ping
pong double buffering makes the flipping code way more complex and it
does not provide any benefit, so it is better to switch to single
buffer operation.
There is still one problem in updating the framebuffer dma address on
the fly. There are two registers defining the framebuffer dma area and
things may break if the dma address is fetched in while the registers
are are being updated.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Cleanup irq handling. Clear the irq status unconditionally and
restructure the status bit conditions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Remove broken error handling. The condition for handling the
LCDC_SYNC_LOST and LCDC_FIFO_UNDERFLOW could never be satisfied as the
LCDC_SYNC_LOST interrupt is not enabled. Also the requirement to have
both LCDC_SYNC_LOST and LCDC_FIFO_UNDERFLOW fired at once before
handling the error looks weird.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Split reset to a separate function and use usleep_range(250, 1000)
instead of msleep(1) to to keep the reset bit on long enough.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch, changed mdelay(500) to usleep_range(250, 1000)]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Disable crtc on unload. Call tilcdc_crtc_dpms() with DRM_MODE_DPMS_OFF
in the beginning of unload function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Cleanup runtime PM handling. Before the patch the usage of pm_runtime
calls was inconsistent and hard to follow. After the update the
pm_runtime calls are removed from set_scanout() and called around
major operations that access the HW. After the patch the DPMS code does
not have pm_runtime_forbid/allow calls any more and
pm_runtime_irq_safe() is not set anymore.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[Added description to the patch]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Allocate suspend/resume register storage based on the actual number
registers the driver is aware of. The static allocation for register
storage had fallen behind badly.
Reported-by: Michael Bode <michael@bumbleB.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix build error when !CONFIG_CPU_FREQ
drivers/gpu/drm/tilcdc/tilcdc_drv.c: In function 'tilcdc_load':
drivers/gpu/drm/tilcdc/tilcdc_drv.c:327:1: error: label 'fail_put_clk' defined but not used [-Werror=unused-label]
fail_put_clk:
^
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is nothing special about tilcdc HW when the video memory is
concerned. Just using the standard drm helpers for implementation is
enough.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The LCD controller must be deactivated and all DMA transactions stopped
when the suspend power state is entered otherwise the PRCM causes the L3
bus to get stuck in transition state.
This commit forces the lcdc to be shut down and waits for all pending DMA
transactions to complete as part of the suspend handler for this driver.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The frame_done interrupt was only being enabled when the vsync
interrupts were being enabled by DRM. However the frame_done is
used to determine if the LCD controller has successfully completed
the raster_enable, raster_disable commands and the vsync interrupts
are not always enabled during these operations.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On BeagleBone Black if no HDMI monitor is connected and suspend
is requested a kernel panic will result:
root@am335x-evm:~# echo mem > /sys/power/state
[ 65.548710] PM: Syncing filesystems ... done.
[ 65.631311] Freezing user space processes ... (elapsed 0.006 seconds) done.
[ 65.648619] Freezing remaining freezable tasks ... (elapsed 0.005 seconds) done.
[ 65.833500] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa30e004
[ 65.841692] Internal error: : 1028 [#1] SMP ARM
<snip>
[ 66.105287] [<c03765f0>] (platform_pm_suspend) from [<c037b6d4>] (dpm_run_callback+0x34/0x70)
[ 66.114370] [<c037b6d4>] (dpm_run_callback) from [<c037ba84>] (__device_suspend+0x10c/0x2f4)
[ 66.123357] [<c037ba84>] (__device_suspend) from [<c037d004>] (dpm_suspend+0x58/0x218)
[ 66.131796] [<c037d004>] (dpm_suspend) from [<c008d948>] (suspend_devices_and_enter+0x9c/0x3c0)
[ 66.141055] [<c008d948>] (suspend_devices_and_enter) from [<c008de7c>] (pm_suspend+0x210/0x24c)
[ 66.150312] [<c008de7c>] (pm_suspend) from [<c008cabc>] (state_store+0x68/0xb8)
[ 66.158103] [<c008cabc>] (state_store) from [<c02e9654>] (kobj_attr_store+0x14/0x20)
[ 66.166355] [<c02e9654>] (kobj_attr_store) from [<c0185c70>] (sysfs_kf_write+0x4c/0x50)
[ 66.174883] [<c0185c70>] (sysfs_kf_write) from [<c018926c>] (kernfs_fop_write+0xb4/0x150)
[ 66.183598] [<c018926c>] (kernfs_fop_write) from [<c0122638>] (vfs_write+0xa8/0x180)
[ 66.191846] [<c0122638>] (vfs_write) from [<c01229f8>] (SyS_write+0x40/0x8c)
[ 66.199365] [<c01229f8>] (SyS_write) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 66.207426] Code: e595c210 e5932000 e59cc000 e08c2002 (e592c000)
This is because the lcdc module is not enabled when no monitor is detected
to save power. However the suspend handler just blindly tries to save the
lcdc state by copying out the pertinent registers. However module is off
so no good things happen when you try and access it.
This patch only saves off the registers if the module is enabled, and
then only restores the registers on resume if they were saved off during
suspend.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Update tilcdc driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
LCDC hardware does not support fb pitch that is different (i.e. larger)
than the screen size. The driver currently does no checks for this, and
the results of too big pitch are are flickering and lower fps.
This issue easily happens when using libdrm's modetest tool with non-32
bpp modes. As modetest always allocated 4 bytes per pixel, it implies a
bigger pitch for 16 or 24 bpp modes.
This patch adds a check to reject pitches the hardware cannot support.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Updating the tilcdc DRM driver code to calculate the LCD controller
pixel clock more accurately. Based on a suggested implementation by
Tomi Valkeinen.
The current code does not work correctly and produces wrong results
with many requested clock rates. It also oddly uses two different
clocks, a display pll clock and a divider clock (child of display
pll), instead of just using the clock coming to the lcdc.
This patch removes the use of the display pll clock, and rewrites the
code to calculate the clock rates. The idea is simply to request a
clock rate of pixelclock*2, as the LCD controller has an internal
divider which we set to 2.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
[Rewrapped description]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently we perform our own wait in post_plane_update,
but the atomic core performs another one in wait_for_vblanks.
This means that 2 vblanks are done when a fb is changed,
which is a bit overkill.
Merge them by creating a helper function that takes a crtc mask
for the planes to wait on.
The broadwell vblank workaround may look gone entirely but this is
not the case. pipe_config->wm_changed is set to true
when any plane is turned on, which forces a vblank wait.
Changes since v1:
- Removing the double vblank wait on broadwell moved to its own commit.
Changes since v2:
- Move out POWER_DOMAIN_MODESET handling to its own commit.
Changes since v3:
- Do not wait for vblank on legacy cursor updates. (Ville)
- Move broadwell vblank workaround comment to page_flip_finished. (Ville)
Changes since v4:
- Compile fix, legacy_cursor_flip -> *_update.
Changes since v5:
- Kill brackets.
- Add WARN_ON when wait_for_vblanks fails.
- Remove extra newlines.
- Split the checks whether vblank is needed to a separate function,
with comments why a vblank is needed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56CD84DA.5030507@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
HP EliteBook 755 G2 with ALC3228 (ALC280) codec [103c:221c] requires
the known fixup (ALC269_FIXUP_HEADSET_MIC) for making the headset mic
working. Also, it suffers from the loopback noise problem, so we
should disable aamix path as well.
Reported-by: Derick Eddington <derick.eddington@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a directory is deleted, we don't take too much care about killing off
all the dirents that belong to it — on the basis that on remount, the scan
will conclude that the directory is dead anyway.
This doesn't work though, when the deleted directory contained a child
directory which was moved *out*. In the early stages of the fs build
we can then end up with an apparent hard link, with the child directory
appearing both in its true location, and as a child of the original
directory which are this stage of the mount process we don't *yet* know
is defunct.
To resolve this, take out the early special-casing of the "directories
shall not have hard links" rule in jffs2_build_inode_pass1(), and let the
normal nlink processing happen for directories as well as other inodes.
Then later in the build process we can set ic->pino_nlink to the parent
inode#, as is required for directories during normal operaton, instead
of the nlink. And complain only *then* about hard links which are still
in evidence even after killing off all the unreachable paths.
Reported-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
With this fix, all code paths should now be obtaining the page lock before
f->sem.
Reported-by: Szabó Tamás <sztomi89@gmail.com>
Tested-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org
