Nic firmware can place resources (queues, intrs, etc) on multiple BARs, so
allow driver to discover/map resources beyond BAR0.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its hard to tell if vlans are dropping frames, since
every frame given to vlan_???_start_xmit() functions
is accounted as fully transmitted by lower device.
We can test dev_queue_xmit() return values to
properly account for dropped frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan devices are currently not multi-queue capable.
We can do that defining rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()
This new method gets num_tx_queues/real_num_tx_queues
from lower device.
macvlan_get_tx_queues() is a copy of vlan_get_tx_queues().
Because macvlan_start_xmit() has to update netdev_queue
stats only (and not dev->stats), I chose to change
tx_errors/tx_aborted_errors accounting to tx_dropped,
since netdev_queue structure doesnt define tx_errors /
tx_aborted_errors.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few drivers still access the arguments to MDIO ioctls as an array of
u16. Convert them to use struct mii_ioctl_data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard MDIO ioctl numbers are well-established and these should
no longer be needed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While perusing vendor driver, I saw that it did not enable the Vaux
power unless device was able to wake from lan for D3cold.
This might help for Rene's power issue.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a perpetual while() loop in unwinding partial
mapped tx skb on dma mapping failure.
Reported-by: "Juha Leppanen" <juha_motorsportcom@luukku.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate calls to netxen_napi_add().
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alloc 12k skbuffs so that firmware can aggregate more
packets into one buffer. This doesn't raise memory
consumption since 9k skbs use 16k slab cache anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FCoE DDP in 82599 can be used for both FCoE initiator as well as FCoE
target, depending on the indication of the exchange being the responder or
originator in the F_CTL (frame control) field in the encapsulated Fiber
Channel frame header (T10 Spec., FC-FS). For the initiator, OX_ID is used
for FCoE DDP, where for the target RX_ID is used for FCoE DDP.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a simple selection of a FCoE tx queue based on the current cpu id to
distribute transmission of FCoE traffic evenly among multiple FCoE transmit
queues.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for multiple transmit queues to the Fiber Channel
over Ethernet (FCoE) feature found in 82599. Currently, FCoE has multiple
Rx queues available, along with a redirection table, that helps distribute
the I/O load across multiple CPUs based on the FC exchange ID. To make
this the most effective, we need to provide the same layout of transmit
queues to match receive.
Particularly, when Data Center Bridging (DCB) is enabled, the designated
traffic class for FCoE can have dedicated queues for just FCoE traffic,
while not affecting any other type of traffic flow.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates things so that vlan tags are taken into account when
setting the receive large packet maximum length. This allows the VF driver
to correctly receive full sized frames when vlans are enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb_irq_disable/enable calls were causing virtual functions associated
with the igb physical function to have their interrupts disabled. In order
to prevent this from occuring we should only clear/set the bits related to
the physical function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the set_rx_mode netdevice operation so that igb
can better support multiple unicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current sched domain creation code can't handle multi-node processors.
When switching to power_savings scheduling errors show up and
system might hang later on (due to broken sched domain hierarchy):
# echo 0 >> /sys/devices/system/cpu/sched_mc_power_savings
CPU0 attaching sched-domain:
domain 0: span 0-5 level MC
groups: 0 1 2 3 4 5
domain 1: span 0-23 level NODE
groups: 0-5 6-11 18-23 12-17
...
# echo 1 >> /sys/devices/system/cpu/sched_mc_power_savings
CPU0 attaching sched-domain:
domain 0: span 0-11 level MC
groups: 0 1 2 3 4 5 6 7 8 9 10 11
ERROR: parent span is not a superset of domain->span
domain 1: span 0-5 level CPU
ERROR: domain->groups does not contain CPU0
groups: 6-11 (__cpu_power = 12288)
ERROR: groups don't span domain->span
domain 2: span 0-23 level NODE
groups:
ERROR: domain->cpu_power not set
ERROR: groups don't span domain->span
...
Fixing all aspects of power-savings scheduling for Magny-Cours needs
some larger changes in the sched domain creation code.
As a short-term and temporary workaround avoid the problems by
extending "the worst possible hack" ;-(
and always use llc_shared_map on AMD Magny-Cours when MC domain span
is calculated.
With this I get:
# echo 1 >> /sys/devices/system/cpu/sched_mc_power_savings
CPU0 attaching sched-domain:
domain 0: span 0-5 level MC
groups: 0 1 2 3 4 5
domain 1: span 0-5 level CPU
groups: 0-5 (__cpu_power = 6144)
domain 2: span 0-23 level NODE
groups: 0-5 (__cpu_power = 6144) 6-11 (__cpu_power = 6144) 18-23 (__cpu_power = 6144) 12-17 (__cpu_power = 6144)
...
I.e. no errors during sched domain creation, no system hangs, and also
mc_power_savings scheduling works to a certain extend.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes threshold_bank4 support on multi-node processors.
The correct mask to use is llc_shared_map, representing an internal
node on Magny-Cours.
We need to create 2 sets of symlinks for sibling shared banks -- one
set for each internal node, symlinks of each set should target the
first core on same internal node.
Currently only one set is created where all symlinks are targeting
the first core of the entire socket.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
L3 cache size, associativity and shared_cpu information need to be
adapted to show information for an internal node instead of the
entire physical package.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Construct entire NodeID and use it as cpu_llc_id. Thus internal node
siblings are stored in llc_shared_map.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
kmem_cache_destroy() should call rcu_barrier() *after* kmem_cache_close() and
*before* sysfs_slab_remove() or risk rcu_free_slab() being called after
kmem_cache is deleted (kfreed).
rmmod nf_conntrack can crash the machine because it has to kmem_cache_destroy()
a SLAB_DESTROY_BY_RCU enabled cache.
Cc: <stable@kernel.org>
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
The Intel Optimization Reference Guide says:
In Intel Atom microarchitecture, the address generation unit
assumes that the segment base will be 0 by default. Non-zero
segment base will cause load and store operations to experience
a delay.
- If the segment base isn't aligned to a cache line
boundary, the max throughput of memory operations is
reduced to one [e]very 9 cycles.
[...]
Assembly/Compiler Coding Rule 15. (H impact, ML generality)
For Intel Atom processors, use segments with base set to 0
whenever possible; avoid non-zero segment base address that is
not aligned to cache line boundary at all cost.
We can't avoid having a non-zero base for the stack-protector
segment, but we can make it cache-aligned.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: <stable@kernel.org>
LKML-Reference: <4AA01893.6000507@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The macro was defined in the 32-bit path as well - breaking the
build on 32-bit platforms:
arch/x86/lib/msr-reg.S: Assembler messages:
arch/x86/lib/msr-reg.S:53: Error: Bad macro parameter list
arch/x86/lib/msr-reg.S💯 Error: invalid character '_' in mnemonic
arch/x86/lib/msr-reg.S:101: Error: invalid character '_' in mnemonic
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-f6909f394c2d4a0a71320797df72d54c49c5927e@git.kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When CONFIG_SLUB_DEBUG is enabled, sysfs_slab_add should unlink and put the
kobject if sysfs_create_group failed. Otherwise, sysfs_slab_add returns error
then free kmem_cache s, thus memory of s->kobj is leaked.
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
We forget to release the fd in the PERF_FLAG_FD_OUTPUT
error path.
Reorganize the error flow here to be a clean fall-through
logic.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's a large cut and paste chunk of code in smb_init and
small_smb_init to handle reconnects. Break it out into a separate
function, clean it up and have both routines call it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We did not account for the enclosing \0. Depending on what malloc()
gave us this resulted in corrupted version string printouts.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Print out more accurate timestamps - usecs does not cut it
anymore on fast enough boxes ;-)
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Leave the input fd at the data area.
It does not matter right now - but seeking at the end of it
certainly did not make sense.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no dependency from the gart code to the agp code.
And since a lot of systems today do not have agp anymore
remove this dependency from the kernel configuration.
Signed-off-by: Pavel Vasilyev <pavel@pavlinux.ru>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
We started parsing perf.data at head 0. This caused -D to
segfault and it could possibly also case incorrect trace
entries to be displayed.
Parse it at data_offset instead.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch enables the passthrough mode for AMD IOMMU by
running the initialization function when iommu=pt is passed
on the kernel command line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch makes sure a device is not detached from the
passthrough domain when the device driver is unloaded or
does otherwise release the device.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When the IOMMU driver runs in passthrough mode it has to
make sure that every device not assigned to an IOMMU-API
domain must be put into the passthrough domain instead of
keeping it unassigned.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch makes the locking behavior between the functions
attach_device and __attach_device consistent with the
locking behavior between detach_device and __detach_device.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The V bit of the device table entry has to be set after the
rest of the entry is written to not confuse the hardware.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
When iommu=pt is passed on kernel command line the devices
should run untranslated. This requires the allocation of a
special domain for that purpose. This patch implements the
allocation and initialization path for iommu=pt.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch factors some code of protection domain allocation
into seperate functions. This way the logic can be used to
allocate the passthrough domain later. As a side effect this
patch fixes an unlikely domain id leakage bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This variable is read most of the time. This patch marks it
as such. It also documents the meaning the this variable
while at it.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch adds a map_size parameter to the iommu_map_page
function which makes it generic enough to handle multiple
page sizes. This also requires a change to alloc_pte which
is also done in this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The driver now supports a dynamic number of levels for IO
page tables. This allows to reduce the number of levels for
dma_ops domains by one because a dma_ops domain has usually
an address space size between 128MB and 4G.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch changes the alloc_pte function to be able to map
pages into the whole 64 bit address space supported by AMD
IOMMU hardware from the old limit of 2**39 bytes.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
