Add support for the Atmel AT91SAM9263 processor. It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.
These changes are:
* The system peripheral I/O region we remap has increased from
0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
* The increased I/O region forces changes to entry-macro.S and
debug-macro.S due to ARM's limited immediate offset addressing
modes.
* Maximum number of GPIO banks increases to 5.
* 2 MMC controllers so the board-setup code needs to specify which
controller it wishes to use when calling at91_add_device_mmc().
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix build failure of AT91SAM9260.
The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a
"struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263)
ethernet driver (macb.c) [developed on the AVR32 architecture] expects a
"struct eth_platform_data".
Since the platform data of the two drivers is very similar, we continue
to use the "struct at91_eth_data" for all AT91 processors but add a
#define eth_platform_data at91_eth_data
in board.h to keep the MACB driver happy.
Original patch by Jan Altenberg.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA cache handling functions take virtual addresses, but in the
form of unsigned long arguments. This leads to a little confusion
about what exactly they take. So, convert them to take const void *
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The outer cache can be L2 as on RealView/EB MPCore platform or even L3
or further on ARMv7 cores. This patch adds the generic support for
flushing the outer cache in the DMA operations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Memory allocated by the coherent memory allocators will be marked
uncacheable, which means it's pointless calling consistent_sync()
to perform cache maintainence on this memory; it's just a waste of
CPU cycles.
Moreover, with the (subsequent) merge of outer cache support, it
actually breaks things to call consistent_sync() on anything but
direct-mapped memory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to ARM ARM, changes to the CP15 registers are only
guaranteed to be visible after an Instruction Synchronization Barrier
(ISB). This patch adds the ISB at the end of set_cr and
set_copro_access functions and also moves them further down in the
file, below the isb macro definition.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The architecture specification states that TLB operations are
guaranteed to be complete only after the execution of a DSB (Data
Synchronisation Barrier, former Data Write Barrier or Drain Write
Buffer). The branch target cache invalidation is also needed. The ISB
(Instruction Synchronisation Barrier, formerly Prefetch Flush) is
needed unless there will be a return from exception before the
corresponding mapping is used (i.e. user mappings).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On newer architectures (ARMv6, ARMv7), the depth of the prefetch and
branch prediction is implementation defined and there is a small risk
of wrong ASID tagging when changing TTBR0 before setting the new
context id. The recommended solution is to set a reserved ASID during
TTBR changing. This patch reserves ASID 0.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM Architecture Reference Manual specifies that a prefetch flush
is needed after changing the DACR register (chapter B2.7.6).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are three barriers - ISB, DMB and DSB for different
scenarious. This patch adds their definitions in the system.h file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up proc-xsc3:
- Correct a number of typos.
- Fix up indentation in a number of places.
- Change references to the various caches to be more clear about
whether we're talking about the L1 D, the L1 I or the unified L2
cache.
- Rename "drain write buffer" to "data write barrier", the official
name used in the Manzano manual.
- Change the xsc3 cpu name from "XScale-Core3" to "XScale-V3 based
processor".
Also, since a previously merged patch implements proper support for
using a MAC or iWMMXt coprocessor on xsc3 platforms, we no longer
need to enable access to CP0 on boot.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the setting of HWCAP_CRUNCH to kernel/crunch.c, where it belongs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the i2c-pxa driver to actually using the platform device information and let it handle the power i2c bus on pxa27x too. Original version of this patch didn't compile with CONFIG_I2C_PXA_SLAVE set.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_device setup code for OTG/peripheral mode of 834x DR module.
It is needed for USB client driver to work.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add board specific initialization code for USB to work in both MPH and DR
mode for MPC8349E MDS-PB board.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added a new dr_mode property to describe what mode the DR controller is being
used in (host, device, OTG). Updated the MPC8349E MDS dts with this new property.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the mpc8313erdb defconfig
Signed-off-by: Wilson Lo <Wilson.Lo@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8313E Reference Development Board (RDB). The board
is a mini-ITX reference board with 128M DDR2, 8M flash, 32M NAND, USB, PCI,
gigabit ethernet, and serial.
Signed-off-by: Wilson Lo <Wilson.Lo@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 2943ecf2ed.
This should go through the SPI maintainer, it was my fault that it did
not. Especially as it conflicts with other patches he has pending.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following macro :
include/asm-powerpc/vga.h:#define VGA_MAP_MEM(x,s) (x + vgacon_remap_base)
is used by drivers/video/console/vgacon.c which can be compiled as a module
(drivers/video/vga16fb.ko).
Therefore, vgacon_remap_base should be exported.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/mm/mem.c states that page_is_ram is called by the code that
implements /dev/mem, which isn't true. Remove the comment.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When the windfarm thread gets a suspend signal it will die instead of
freezing. This fixes it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kernel/irq.c contains a comment that speaks of -1 and -2 as interrupt
numbers, but this is actually dependent on configuration options now.
Replace by NO_IRQ and NO_IRQ_ENABLED.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix two problems in the book-e watchdog driver.
a) The 4xx default period was defined wrong
b) Clear status before enabling the watchdog exception
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use ARRAY_SIZE macro already defined in linux/kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In preparation for marking file_operations as const.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the appropriate logging macro for the priority level for that
printk call.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It looks like GNU make version 3.80 (but apparently not 3.81) adds
leading whitespace to the result of the checker-shell execution. This
strips them off explicitly.
Also, don't bother symlinking the output file to /dev/null. It's likely
as expensive as just writing the temp-file, and we need to remove it
anyway afterwards.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (70 commits)
USB: remove duplicate device id from zc0301
USB: remove duplicate device id from usb_storage
USB: remove duplicate device id from keyspan
USB: remove duplicate device id from ftdi_sio
USB: remove duplicate device id from visor
USB: a bit more coding style cleanup
usbcore: trivial whitespace fixes
usb-storage: use first bulk endpoints, not last
EHCI: fix interrupt-driven remote wakeup
USB: switch ehci-hcd to new polling scheme
USB: autosuspend for usb printer driver
USB Input: Added kernel module to support all GTCO CalComp USB InterWrite School products
USB: Sierra Wireless auto set D0
USB: usb ethernet gadget recognizes HUSB2DEV
USB: list atmel husb2_udc gadget controller
USB: gadgetfs AIO tweaks
USB: gadgetfs behaves better on userspace init bug
USB: gadgetfs race fix
USB: gadgetfs simplifications
USB: gadgetfs cleanups
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (28 commits)
sysfs: Shadow directory support
Driver Core: Increase the default timeout value of the firmware subsystem
Driver core: allow to delay the uevent at device creation time
Driver core: add device_type to struct device
Driver core: add uevent vars for devices of a class
SYSFS: Fix missing include of list.h in sysfs.h
HOWTO: Add a reference to Harbison and Steele
sysfs: error handling in sysfs, fill_read_buffer()
kobject: kobject_put cleanup
sysfs: kobject_put cleanup
sysfs: suppress lockdep warnings
Driver core: fix race in sysfs between sysfs_remove_file() and read()/write()
driver core: Change function call order in device_bind_driver().
driver core: Don't stop probing on ->probe errors.
driver core fixes: device_register() retval check in platform.c
driver core fixes: make_class_name() retval checks
/sys/modules/*/holders
USB: add the sysfs driver name to all modules
SERIO: add the sysfs driver name to all modules
PCI: add the sysfs driver name to all modules
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (116 commits)
sk98lin: planned removal
AT91: MACB support
sky2: version 1.12
sky2: add new chip ids
sky2: Yukon Extreme support
sky2: safer transmit timeout
sky2: TSO support for EC_U
sky2: use dev_err for error reports
sky2: add Wake On Lan support
fix unaligned exception in /drivers/net/wireless/orinoco.c
Remove unused kernel config option DLCI_COUNT
z85230: spinlock logic
mips: declance: Driver model for the PMAD-A
Spidernet: Rework RX linked list
NET: turn local_save_flags() + local_irq_disable() into local_irq_save()
NET-3c59x: turn local_save_flags() + local_irq_disable() into local_irq_save()
hp100: convert pci_module_init() to pci_register_driver()
NetXen: Added ethtool support for user level tools.
NetXen: Firmware crb init changes.
maintainers: add atl1 maintainers
...
Remove the memory manager parameter from the put_block function, as this
makes the client code a lot cleaner. Prepare buffer manager for lock and
unlock calls.
Fix buggy aligned allocations.
Remove the stupid root_node field from the core memory manager.
Support multi-page buffer offset alignments
Add improved alignment functionality to the core memory manager.
This makes an allocated block actually align itself and returns any
wasted space to the manager.
Signed-off-by: Dave Airlie <airlied@linux.ie>
hch originally submitted this for paravirt ops work, airlied took it
and cleaned up a lot of unused code caused by using this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Airlie <airlied@linux.ie>
