wm8903_platform_data.gpio_cfg[] was intended to be interpreted as follows:
0: Don't touch this GPIO's configuration register
1..7fff: Write that value to the GPIO's configuration register
8000: Write zero to the GPIO's configuration register
other: Undefined (invalid)
The rationale is that platform data is usually global data, and a value of
zero means that the field wasn't explicitly set to anything (e.g. because
the field was new to the pdata type, and existing users weren't update to
initialize it) and hence the value zero should be ignored. 0x8000 is an
explicit way to get 0 in the register.
The code worked this way until commit 7cfe561 "ASoC: wm8903: Expose GPIOs
through gpiolib", where the behaviour was changed due to my lack of
awareness of the above rationale.
This patch reverts to the intended behaviour, and updates all in-tree users
to use the correct scheme. This also makes WM8903 consistent with other
devices that use a similar scheme.
WM8903_GPIO_NO_CONFIG is also renamed to WM8903_GPIO_CONFIG_ZERO so that
its name accurately reflects its purpose.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using gpio_request_one can make the error handling simpler.
Also remove a redundant "Failed to issue reset" error message.
We already show the error message in uda1380_reset() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error for uda1380_modinit if i2c_add_driver() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When no platform data is supplied, point pdata at a default platform
structure. This enables two future changes:
a) Defines the default platform data values in a single place.
b) There is always a valid pdata pointer, so some conditional code can
be simplified by a later patch.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get control of the device earlier and avoid trying to do an ASoC probe
on a card that won't work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Converting to an rbtree cache as regcache doesn't have a flat cache.
Since the top of the register map is fairly sparse this should be an
overall win.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
We only do this on initial power on so it's at best a waste of time as
the core will have already defaulted to the same values.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The driver used to use a complicated method to sync the register cache
after having brought the bias level up to standby in resume due to the
use of the write sequencer to manage the initial power up. Now that we
don't use the write sequencer there is no need for this and we can just
use snd_soc_cache_sync() directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Since they don't actually have power bits but do have events associated
with them it's important that we bootstrap their state properly which
making them virtual does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The GPIO registers are 15 bits wide. Hence values, higher than 0x7fff are
not legal GPIO register values. Modify the pdata.gpio_cfg handling code
to reject all illegal values, not just WM8903_GPIO_NO_CONFIG (0x8000). This
will allow the later use of 0xffffffff as an invalid value in future device
tree bindings, meaning "don't touch this GPIO's configuration".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Still have a manual free in there for some realloc()ed memory as there's
no devm version of that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to rerun DAPM if the clock source is the same but we do
need to adjust the microphone detection rate in case we are moving from
an audio to a non-audio rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
