Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following batch contains netfilter fixes for your net tree, they are:
1) Fix use after free in nfnetlink when sending a batch for some
unsupported subsystem, from Denys Fedoryshchenko.
2) Skip autoload of the nat module if no binding is specified via
ctnetlink, from Florian Westphal.
3) Set local_df after netfilter defragmentation to avoid a bogus ICMP
fragmentation needed in the forwarding path, also from Florian.
4) Fix potential user after free in ip6_route_me_harder() when returning
the error code to the upper layers, from Sergey Popovich.
5) Skip possible bogus ICMP time exceeded emitted from the router (not
valid according to RFC) if conntrack zones are used, from Vasily Averin.
6) Fix fragment handling when nf_defrag_ipv4 is loaded but nf_conntrack
is not present, also from Vasily.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If sdata doesn't have a valid dev (e.g. in case of monitor
vif), the vif_name field was initialized with (a length of)
some short string, but later was set to a different,
potentially larger one.
This resulted in out-of-bounds write, which usually
appeared as garbage in the trace log.
Simply trace sdata->name, as it should always have the
correct name for both cases.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch increments the management interface revision due to the
changes with the Device Found management event and other fixes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two (related) issues with this.
One case, reported by Michal, is related to hostap: it unsets the
20/40 capability bit for stations that associate when it's in 20
MHz mode.
The other case, reported by Eyal, is that some APs like Netgear
R6300v2 and probably others based on the BCM4360 chipset can be
configured for doing VHT at 20Mhz. In this case the beacon has
a VHT IE but the HT cap indicates transmitter only support 20Mhz.
In both of these cases, we currently avoid VHT and use only HT
this means we can't use the highest rates (MCS8), so fixing this
leads to throughput improvements.
Reported-by: Michal Kazior <michal.kazior@tieto.com>
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Each node action flag should be set or cleared separately, instead
we now set the whole flags variable in one shot, and it's turned
out to be hard to see which other flags are affected. Therefore,
for instance, we explicitly clear TIPC_WAIT_OWN_LINKS_DOWN bit in
node_lost_contact().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename node flags to action_flags as well as its enum names so
that they can reflect its real meanings.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validating the UDP checksum is now done in UDP before handing
packets to the encapsulation layer. Note that this also eliminates
the "feature" where L2TP can ignore a non-zero UDP checksum (doing
this was contrary to RFC 1122).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving validation of UDP checksum to be done in UDP not encap layer.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_simple_validate to verify checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_simple_validate to verify checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_simple_validate to verify checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_simple_validate to verify checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the callers hold RTNL lock, so there is no need to use inet_addr_hash_lock
to protect the hash list.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.
BTW, rename it to ->ping_group_range instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.
Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dst is released one line before we access it again with dst->error.
Fixes: 58e35d1471 netfilter: ipv6: propagate routing errors from
ip6_route_me_harder()
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds support to store RSSI for connection when reply for
HCI_Read_RSSI is received.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Invalid Parameters error code is used to indicate that the command
length is invalid or that a parameter is outside of the specified range.
This error code wasn't clearly specified in the Bluetooth 4.0
specification but since 4.1 this has been fixed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 59af6928 (mac80211: fix CSA tx queue stopping) introduced a
sparse warning:
net/mac80211/cfg.c:3274:5: warning: symbol '__ieee80211_channel_switch' was not declared. Should it be static?
Fix it by declaring the function static.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't make much sense to leave a crippled
interface running.
As a side effect this will unblock tx queues with
CSA reason immediately after failure instead of
until after userspace requests interface to stop.
This also gives userspace an opportunity to
indirectly see CSA failure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[small code cleanup]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Increment fib_info_cnt in fib_create_info() right after successfuly
alllocating fib_info structure, overwise fib_metrics allocation failure
leads to fib_info_cnt incorrectly decremented in free_fib_info(), called
on error path from fib_create_info().
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d206940319,
there are no more callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing the segmentation in the forward path has one major drawback:
When using virtio, we may process gso udp packets coming
from host network stack. In that case, netfilter POSTROUTING
will see one packet with udp header followed by multiple ip
fragments.
Delay the segmentation and do it after POSTROUTING invocation
to avoid this.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.
We must thus first test the largest original frag size vs. mtu, and not
vice versa.
Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but
1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.
This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.
Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).
While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If gpio controller requires waiting for read and write
GPIO values, then we have to use the gpio cansleep api.
Fix the rfkill_gpio_set_power which calls only the
nonsleep version (causing kernel warning).
There is no problem to use the cansleep version here
because we are not in IRQ handler or similar context
(cf rfkill_set_block).
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is not guaranteed that multi-vif channel
switching is tightly synchronized. It makes sense
to ignore cqm (missing beacons, et al) while csa
is progressing and re-check it after it completes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible for tx queues to be stuck stopped
if AP CSA finalization failed. In that case
neither stop_ap nor do_stop woke the queues up.
This means it was impossible to perform tx at all
until driver was reloaded or a successful CSA was
performed later.
It was possible to solve this in a simpler manner
however this is more robust and future proof
(having multi-vif CSA in mind).
New sdata->csa_block_tx is introduced to keep
track of which interfaces requested tx to be
blocked for CSA. This is required because mac80211
stops all tx queues for that purpose. This means
queues must be awoken only when last tx-blocking
CSA interface is finished.
It is still possible to have tx queues stopped
after CSA failure but as soon as offending
interfaces are stopped from userspace (stop_ap or
ifdown) tx queues are woken up properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't catch the case if an unsupported protocol is submitted
to the xfrm6 protocol handlers, this can lead to NULL pointer
dereferences. Fix this by adding the appropriate checks.
Fixes: 7e14ea15 ("xfrm6: Add IPsec protocol multiplexer")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Commit 4068579e1e ("net: Implmement
RFC 6936 (zero RX csums for UDP/IPv6)") introduced zero checksums
being allowed for IPv6, but in the case that a socket disallows a
zero checksum on RX we need to sock_put.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling CONFIG_DEBUG_ATOMIC_SLEEP has shown that some rfcomm functions
acquiring spinlocks call sleeping locks further in the chain. Converting
the offending spinlocks into mutexes makes sleeping safe.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
Pull Ceph fixes from Sage Weil:
"First, there is a critical fix for the new primary-affinity function
that went into -rc1.
The second batch of patches from Zheng fix a range of problems with
directory fragmentation, readdir, and a few odds and ends for cephfs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: reserve caps for file layout/lock MDS requests
ceph: avoid releasing caps that are being used
ceph: clear directory's completeness when creating file
libceph: fix non-default values check in apply_primary_affinity()
ceph: use fpos_cmp() to compare dentry positions
ceph: check directory's completeness before emitting directory entry
In the previous commits of this series, we removed all asynchronous
actions which were based on the tasklet handler - "tipc_k_signal()".
So the moment has now come when we can completely remove the tasklet
handler infrastructure. That is done with this commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of resetting all links until after bclink
lock is released, avoiding to asynchronously reset all links.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert allocations of global variables associated with bclink from
static way to dynamical way for the convenience of bclink instance
initialisation. Meanwhile, this also helps TIPC support name space
in the future easily.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are going to do more jobs when bc_lock is released, the two
operations of holding/releasing the lock should be encapsulated with
functions. In addition, we move bc_lock spin lock into tipc_bclink
structure avoiding to define the global variable.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of delivering name tables until after node
lock is released, avoiding to do it under asynchronous context.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since previously what all publications pertaining to the lost node
were removed from name table was finished in tasklet context
asynchronously, we need to TIPC_NAMES_GONE flag indicating whether
the node cleanup work is finished or not. But now as the cleanup work
has been finished when node lock is released, the flag becomes
meaningless for us.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Postpone the actions of notifying subscriptions until after node lock
is released, avoiding to asynchronously execute registered handlers
when node is lost.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
