Commit 90173882ed ("omap: add dsp platform
device") used CONFIG_BRIDGE_DVFS were it obviously meant
CONFIG_TIDSPBRIDGE_DVFS. Fix that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3_noncore_dpll_set_rate() attempts an enable of bypass clk as well
as ref clk for every .set_rate attempt on a noncore DPLL, regardless of
whether the .set_rate results in the DPLL being locked or put in bypass.
Early at boot, while some of these DPLLs are programmed and locked
(using .set_rate for the DPLL), this causes an ordering issue.
For instance, on OMAP5, the USB DPLL derives its bypass clk from ABE DPLL.
If a .set_rate of USB DPLL which programmes the M,N and locks it is called
before the one for ABE, the enable of USB bypass clk (derived from ABE DPLL)
then attempts to lock the ABE DPLL and fails as the M,N values for ABE
are yet to be programmed.
To get rid of this ordering needs, enable bypass clk for a DPLL as part
of its .set_rate only when its being put in bypass, and only enable the
ref clk when its locked.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_pwrdm_save_clkdm_state_and_activate() tried to test one of its
unsigned arguments to determine whether it was less than zero. Fix by
moving the error test to the caller.
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod
framework. Just get rid of it, so we have one less flag to
worry about.
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
WDT1 module can take one of the below clocks as input functional
clock -
- On-Chip 32K RC Osc [default/reset]
- 32K from PRCM
The On-Chip 32K RC Osc clock is not an accurate clock-source as per
the design/spec, so as a result, for example, timer which supposed
to get expired @60Sec, but will expire somewhere ~@40Sec, which is
not expected by any use-case.
The solution here is to switch the input clock-source to PRCM
generated 32K clock-source during boot-time itself.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn
makes sure that sysc idle bit-fields are configured to valid state on
enable/disable callbacks.
With the recent submitted patch from Santosh Shilimkar,
"ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc"
(commit: 4a98c2d89), it is required to add sysconf
information to each valid hwmod entry, else device will not be
come out from idle state properly and leads to below kernel
crash -
[2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at
0xf9e35034
[2.198325] Internal error: : 1028 [#1] SMP ARM
[2.203101] Modules linked in:
[2.206334] CPU: 0 Not tainted (3.9.0-rc3-00059-gd114294#1)
[2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60
[2.218090] LR is at omap_wdt_probe+0x184/0x1fc
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
The initialization is done from the cpuidle framework.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the CPUIDLE_FLAG_TIMER_STOP and let the cpuidle framework
to handle the CLOCK_EVT_NOTIFY_BROADCAST_ENTER/EXIT when entering
this state.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the AES0 HIB2 module's hwmod data for the am33xx SoC.
Also, remove it from the '#if 0' block that its currently
inside so the data is actually available for use.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add clock data for for the SHA0 crypto module
on the am33xx SoC.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_init_aes() routine in devices.c only needs to be
called when there is no device tree present.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the error message that prints when there is no AES IP
present to make it consistent with all the other IPs.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the device data for the OMAP3 AES crypto IP
from explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the device data for the OMAP2 AES crypto IP from
explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update the SHA0 HIB2 module's hwmod data for the am33xx SoC.
Also, remove it from the '#if 0' block that its currently
inside so the data is actually available for use.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add clock data for for the SHA0 crypto module
on the am33xx SoC.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_init_sham() routine in devices.c only needs to be
called when there is no device tree present.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the error message that prints when there is no SHA IP
present to make it consistent with all the other IPs.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the device data for the OMAP3 SHAM2 (SHA1/MD5) crypto IP
from explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: updated to use per-SoC registration lists for GP-only hwmods;
fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The current OMAP2 SHAM support doesn't enable DMA
so add that support so it can use DMA just like OMAP3.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert the device data for the OMAP2 SHAM crypto IP from
explicit platform_data to hwmod.
CC: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
[paul@pwsan.com: fixed lines causing sparse warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4460 ROM code bug needs the GIC distributor and local timer
bases to be available for the bug work around. In current code, dt
case these bases are not initialized leading to failure of the
errata work-around.
Fix it by extracting the bases from dt blob and populating them.
Reported-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
UART driver slave idle issue has been taken care by driver using hwmod
framework.
So we can now ger rid off the L4 per clockdomain static dependency with
MPU which was used to wrok around UART wakeup and console sluggishnesh issue
on OMAP4 SOCs.
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
With commit bfd6d021 {ARM: OMAP3+: Implement timer workaround for errata
i103 and i767}, the sync and gptimer synchronization errata got fixed.
Hence the l4_wakeup static dependency with MPU can can be removed
now. Static dependency was one of the proposed workaround but from
power savings perspective, it isn't an ideal workaround.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move the secondary CPU wakeup prepare code under smp_prepare_cpus() where it
belongs. It was remainder of the pen release code which was borrowed from
ARM code initially.
While at it drop the un-necessary sev() and barrier which was under
prepare code.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The smp_wmb() here is out of placed and redundant. So remove it. It is
a left over of the pen_release cleanup mostly.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This was borrowed from ARM versatile code with pen_release mechanism but since
OMAP uses hardware register based synchronisation, pen_release stuff was
dropped. Unfortunately the cacheflush wasn't dropped along with it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This was added with intial port where OMAP PM support wasn't existing
and only simple WFI based hooks were used.
This should have been cleaned up while adding the PM support but some
how fall through cracks.
So remove the cache flush code which is no longer needed now.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP platform, FIQ is reserved for secure environment only. If at all
the FIQ needs to be disabled, it involves going through security
API call. Hence the local_fiq_[enable/disable]() in the OMAP code is bogus.
On GP devices too, the fiq is disabled for non-secure software.
So just get rid of it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Choose the common scratch pad offsets, so that same offsets can work for
OMAP4 and OMAP5 devices. It simplifies code and also allows the re-use as
is on OMAP5 devices. Note that these offsets are used by low power
code for various power state management. They are not hardware register
offsets.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
clock should be registered on a given SoC with per-SoC lists.
Basic build, boot, and power management test results are available at:
http://www.pwsan.com/omap/testlogs/jk_clock_flags_cleanup_3.10/20130318100504/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PjJe
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.10/cleanup
In the OMAP2+ clock data, replace the flags that determine whether a
clock should be registered on a given SoC with per-SoC lists.
Basic build, boot, and power management test results are available at:
http://www.pwsan.com/omap/testlogs/jk_clock_flags_cleanup_3.10/20130318100504/
clk inits on OMAP happen quite early, even before slab is available.
The dependency comes from the fact that the timer init code starts to
use clocks and hwmod and we need clocks to be initialized by then.
There are various problems doing clk inits this early, one is,
not being able to do dynamic clk registrations and hence the
dependency on clk-private.h. The other is, inability to debug
early kernel crashes without enabling DEBUG_LL and earlyprintk.
Doing early clk init also exposed another instance of a kernel
panic due to a BUG() when CONFIG_DEBUG_SLAB is enabled.
[ 0.000000] Kernel BUG at c01174f8 [verbose debug info unavailable]
[ 0.000000] Internal error: Oops - BUG: 0 [#1] SMP ARM
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.9.0-rc1-12179-g72d48f9 #6)
[ 0.000000] PC is at __kmalloc+0x1d4/0x248
[ 0.000000] LR is at __clk_init+0x2e0/0x364
[ 0.000000] pc : [<c01174f8>] lr : [<c0441f54>] psr: 600001d3
[ 0.000000] sp : c076ff28 ip : c065cefc fp : c0441f54
[ 0.000000] r10: 0000001c r9 : 000080d0 r8 : c076ffd4
[ 0.000000] r7 : c074b578 r6 : c0794d88 r5 : 00000040 r4 : 00000000
[ 0.000000] r3 : 00000000 r2 : c07cac70 r1 : 000080d0 r0 : 0000001c
[ 0.000000] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 0.000000] Control: 10c53c7d Table: 8000404a DAC: 00000017
[ 0.000000] Process swapper (pid: 0, stack limit = 0xc076e240)
[ 0.000000] Stack: (0xc076ff28 to 0xc0770000)
[ 0.000000] ff20: 22222222 c0794ec8 c06546e8 00000000 00000040 c0794d88
[ 0.000000] ff40: c074b578 c076ffd4 c07951c8 c076e000 00000000 c0441f54 c074b578 c076ffd4
[ 0.000000] ff60: c0793828 00000040 c0794d88 c074b578 c076ffd4 c0776900 c076e000 c07272ac
[ 0.000000] ff80: 2f800000 c074c968 c07f93d0 c0719780 c076ffa0 c076ff98 00000000 00000000
[ 0.000000] ffa0: 00000000 00000000 00000000 00000001 c074cd6c c077b1ec 8000406a c0715724
[ 0.000000] ffc0: 00000000 00000000 00000000 00000000 00000000 c074c968 10c53c7d c0776974
[ 0.000000] ffe0: c074cd6c c077b1ec 8000406a 411fc092 00000000 80008074 00000000 00000000
[ 0.000000] [<c01174f8>] (__kmalloc+0x1d4/0x248) from [<c0441f54>] (__clk_init+0x2e0/0x364)
[ 0.000000] [<c0441f54>] (__clk_init+0x2e0/0x364) from [<c07272ac>] (omap4xxx_clk_init+0xbc/0x140)
[ 0.000000] [<c07272ac>] (omap4xxx_clk_init+0xbc/0x140) from [<c0719780>] (setup_arch+0x15c/0x284)
[ 0.000000] [<c0719780>] (setup_arch+0x15c/0x284) from [<c0715724>] (start_kernel+0x7c/0x334)
[ 0.000000] [<c0715724>] (start_kernel+0x7c/0x334) from [<80008074>] (0x80008074)
[ 0.000000] Code: e5883004 e1a00006 e28dd00c e8bd8ff0 (e7f001f2)
[ 0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.000000] Kernel panic - not syncing: Attempted to kill the idle task!
It was a know issue, that slab allocations would fail when common
clock core tries to cache parent pointers for mux clocks on OMAP,
and hence a patch 'clk: Allow late cache allocation for clk->parents,
commit 7975059d' was added to work this problem around.
A BUG() within kmalloc() with CONFIG_DEBUG_SLAB enabled was completely
overlooked causing this regression.
More details on the issue reported can be found here,
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg85932.html
With all these issues around clk inits happening way too early, it
makes sense to at least move them to a point where dynamic memory
allocations are possible. So move them to a point just before the
timer code starts using clocks and hwmod.
This should at least pave way for clk inits on OMAP moving to dynamic
clock registrations instead of using the static macros defined in
clk-private.h.
The issue with kernel panic while CONFIG_DEBUG_SLAB is enabled
was reported by Piotr Haber and Tony Lindgren and this patch
fixes the reported issue as well.
Reported-by: Piotr Haber <phaber@broadcom.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.8
Signed-off-by: Tony Lindgren <tony@atomide.com>
All the calls to gic_secondary_init() pass 0 as the first argument.
Since this function is called on each CPU when starting, it can be done
in a platform-independent way via a CPU notifier registered by the GIC
code.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Barry Song <baohua.song@csr.com>
Many of these channel definitions have became unused or were never used
so remove unused definitions from arch/arm/mach-omap2/dma.h using a script
below. See also notes in commit d5e7c86
("ARM: OMAP2+: DMA: Moving OMAP2+ DMA channel definitions to mach-omap2")
for removing remaining ones.
egrep '#define OMAP.*DMA' arch/arm/mach-omap2/dma.h \
|cut -f 1 |cut -d ' ' -f 2 | while read -r i; do \
if [ `git grep -c $i | wc -l` -eq 1 ]; then \
echo "removing" $i; \
sed -i "/${i}/d" arch/arm/mach-omap2/dma.h; \
fi; \
done
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's a (rather subtle) typo in "CONFIG_SMC91x_MODULE". Fix it once
and for all by using IS_ENABLED(), which is designed to avoid issues
like this.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
management regressions. There's also a fix for the OMAP1 OHCI controller.
Basic build, boot, and PM test logs are at:
http://www.pwsan.com/omap/testlogs/fixes_a_3.9-rc/20130314101856/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pU5V
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.9-rc3/fixes
Miscellaneous OMAP fixes for v3.9-rc. These primarily deal with OMAP2+ power
management regressions. There's also a fix for the OMAP1 OHCI controller.
Basic build, boot, and PM test logs are at:
http://www.pwsan.com/omap/testlogs/fixes_a_3.9-rc/20130314101856/
OMAP5 does not have freqsel either, so checks needs to be extended.
Infact only OMAP343X devices has the freqsel support, so fix the check
accordingly so that future patching can be avoided.
Reported-by: Archit Taneja <archit@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Errata i688 is also applicable for OMAP5 based devices. Update the
code so that it can be enabled on OMAP5 devices.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Make use of 'prm_base' so that prm read_inst/write_inst can work on
OMAP5 devices.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The patch removes all the CK_* which were used to identify the family of
processors for which the individual clocks belonged to. Instead now separate
lists are created based on the family of processors.
Boot Tested on: OMAP4430, OMAP4460, Beagle-board, AM33X boards, OMAP2 boards.
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: changed omap_clock_register_links() to omap_clocks_register();
updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Consistently check errors using the usual method used in the kernel
for much of its history. For instance:
int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t)
{
int div;
div = gpmc_calc_divider(t->sync_clk);
if (div < 0)
return div;
static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
{
...
return gpmc_cs_set_timings(cs, t);
.....
ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
if (IS_ERR_VALUE(ret))
return ret;
So, gpmc_cs_set_timings() thinks any negative return value is an error,
but where we check that in higher levels, only a limited range are
errors...
There is only _one_ use of IS_ERR_VALUE() in arch/arm which is really
appropriate, and that is in arch/arm/include/asm/syscall.h:
static inline long syscall_get_error(struct task_struct *task,
struct pt_regs *regs)
{
unsigned long error = regs->ARM_r0;
return IS_ERR_VALUE(error) ? error : 0;
}
because this function really does have to differentiate between error
return values and addresses which look like negative numbers (eg, from
mmap()).
So, here's a patch to remove them from OMAP, except for the above.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 17b7e7d335 ("ARM: OMAP4:
clock/hwmod data: start to remove some IP block control "clocks"")
introduced a regression preventing the L3INIT clockdomain of OMAP4
systems from entering idle. This in turn prevented these systems from
entering full chip clock-stop.
The regression was caused by the incorrect removal of a so-called
"optional functional clock" from the OMAP4 clock data. This wasn't
caught for two reasons. First, I missed the retention entry failure
in the branch test logs:
http://www.pwsan.com/omap/testlogs/cleanup_a_3.9/20130126014242/pm/4460pandaes/4460pandaes_log.txt
Second, the integration data for the OCP2SCP PHY IP block, added by
commit 0c6688753f ("ARM: OMAP4: hwmod
data: add remaining USB-related IP blocks"), should have associated this
clock with the IP block, but did not.
Fix by adding back the so-called "optional" functional clock to the
clock data, and by linking that clock to the OCP2SCP PHY IP block
integration hwmod data.
The problem patch was discovered by J, Keerthy <j-keerthy@ti.com>.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
