Commit graph

31608 commits

Author SHA1 Message Date
Alan Cox
0bc2a79a20 libata: Correct IORDY handling
Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling

1.	We check the wrong bit to see if the device has IORDY
2.	Even then some ancient creaking piles of crap don't support
	SETXFER at all.

The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo
e3667ebf85 libata-link: update Power Management to handle PMP links
Update Power Management to consider PMP links.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo
41bda9c980 libata-link: update hotplug to handle PMP links
Update hotplug to handle PMP links.  When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L.  While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo
9b1e2658fa libata-link: update EH to deal with PMP links
Update ata_eh_autopsy(), ata_eh_report(),
ata_eh_revalidate_and_attach() and ata_eh_recover() to deal with PMP
links.  ata_eh_autopsy() and ata_eh_report() updates are
straightforward.  They just repeat the same operation over all
configured links.  The only change to ata_eh_revalidate_and_attach()
is avoiding calling ->cable_select() on non-host ports.

ata_eh_recover() update is more complex as it first processes all
resets and then performs the rest.  This is necessary as thawing with
some links in unknown state can be dangerous.  ehi->action is cleared
on successful recovery of a link to avoid repeating recovery due to
failures in other links.

ata_eh_recover() iterates over only PMP links if PMP is attached, and,
on failure, the failing link is returned in @failed_link instead of
disabling devices directly.  These are to integrate ata_eh_recover()
into PMP EH later.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo
cf1b86c8ab libata-link: update ata_scsi_error() to handle PMP links
Update ata_scsi_error() to handle PMP links.  As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo
8989805d6d libata-link: add PMP links
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.

printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'.  If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.

If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links.  If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo
dbd826168d libata-link: implement ata_link_abort()
Implement ata_link_abort().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo
4fb37a25b9 libata-link: separate out link initialization functions
Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo
0c88758b5a libata-link: make two port flags HRST_TO_RESUME and SKIP_D2H_BSY link flags
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes.  Move them to
ata_link->flags.  This will allow host and PMP links to have different
attributes.  ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo
0260731f01 libata-link: linkify config/EH related functions
Make the following functions deal with ata_link instead of ata_port.

* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo
cc0680a580 libata-link: linkify reset
Make reset methods and related functions deal with ata_link instead of
ata_port.

* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo
955e57dfde libata-link: linkify EH action helpers
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Tejun Heo
936fd73286 libata-link: linkify PHY-related functions
Make the following PHY-related functions to deal with ata_link instead
of ata_port.

* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Tejun Heo
f58229f806 libata-link: implement and use link/device iterators
Multiple links and different number of devices per link should be
considered to iterate over links and devices.  This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().

This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES.  All such
changes have been examined and nothing should be broken.

While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Tejun Heo
9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Jeff Garzik
640fdb5049 [libata] pdc_adma: convert to new exception handling (EH) framework
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Jeff Garzik
8d7a5da4fc [SCSI] gdth: Remove 2.4.x support, in-kernel changelog
* Remove in-source changelog.  It's archived permanently in git and
    various kernel archives, and changelogs should exist purely in git.

  * Remove 2.4.x kernel support.  It is an active obstacle to
    modernizing this driver, at this point.  This includes killing
    gdth_kcompat.h which is 100% redundant in modern kernels.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:29 -04:00
Christoph Hellwig
8514ef27ee [SCSI] gdth: split out pci probing
Split out per-device pci probing and put it under proper CONFIG_PCI.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:24 -04:00
Christoph Hellwig
706a5d4567 [SCSI] gdth: split out eisa probing
Split eisa probing into it's own helper, and do proper error unwinding.
Protect EISA probind by the proper CONFIG_EISA symbol.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:20 -04:00
Christoph Hellwig
aed91cb520 [SCSI] gdth: split out isa probing
(note: this is ontop of Jeff's pci cleanup patch)

Split out isa probing into a helper of it's own.  Error handling is
cleaned up, but errors are not propagated yet.  Also enclose the isa
probe under the proper CONFIG_ISA symbol instead of the !IA64 hack.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:16 -04:00
Matthew Wilcox
b8bff2aeaf gdth: Make one abuse of scsi_cmnd less obvious
Rather than having internal commands abuse scsi_done to call
  gdth_scsi_done, have all the places that use to call scsi_done directly
  call gdth_scsi_done, which now checks whether the command was internal,
  and calls scsi_done if not.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:11 -04:00
Boaz Harrosh
28424d3a50 [SCSI] NCR5380: Use scsi_eh API for REQUEST_SENSE invocation
- Use new scsi_eh_prep/restor_cmnd() for synchronous
    REQUEST_SENSE invocation.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:07 -04:00
Boaz Harrosh
dff6de73f9 [SCSI] usb storage: use scsi_eh API in REQUEST_SENSE execution
- Use new scsi_eh_prep/restor_cmnd() for synchronous
    REQUEST_SENSE invocation.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:55:02 -04:00
Boaz Harrosh
e1c234685c [SCSI] scsi_error: Refactoring scsi_error to facilitate in synchronous REQUEST_SENSE
- Drivers/transports that want to send a synchronous REQUEST_SENSE command
   as part of their .queuecommand sequence, have 2 new API's that facilitate
   in doing so and abstract them from scsi-ml internals.

   void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd,
	struct scsi_eh_save *sesci, unsigned char *cmnd,
	int cmnd_size, int sense_bytes)

   Will hijack a command and prepare it for request sense if needed.
   And will save any later needed info into a scsi_eh_save structure.

   void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd,
	struct scsi_eh_save *sesci);

   Will undo any changes done to a command by above function. Making
   it ready for completion.

 - Re-factor scsi_send_eh_cmnd() to use above APIs

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:58 -04:00
Boaz Harrosh
55db6c1b8e [SCSI] scsi_error: code cleanup before refactoring of scsi_send_eh_cmnd()
- regrouped variables for easier reviewing of next patch
  - Support of cmnd==NULL in call to scsi_send_eh_cmnd()
  - In the @sense_bytes case set transfer size to the minimum
    size of sense_buffer and passed @sense_bytes. cmnd[4] is
    set accordingly.
  - REQUEST_SENSE is set into cmnd[0] so if @sense_bytes is
    not Zero passed @cmnd should be NULL.
  - Also save/restore resid of failed command.
  - Adjust caller

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:51 -04:00
Gabriel C
2ca482302f [SCSI] fdomain: fix CONFIG_PCI=n warnings
I get this warnings on current git when CONFIG_PCI is not set :

drivers/scsi/fdomain.c:390: warning: 'PCI_dev' defined but not used
drivers/scsi/fdomain.c:1768: warning: 'fdomain_pci_tbl' defined but not used

Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:47 -04:00
Joe Korty
89932697ce [SCSI] dpt_i2o: Fix section mismatch
Fix section mismatch in the Adaptec DPT SCSI Raid driver.

WARNING: vmlinux.o(.init.text+0x1fcd2): Section mismatch:
	reference to .exit.text:adpt_exit (between 'adpt_init' and 'ahc_linux_init')

This warning is due to adaptec device detection calling the exit routine on
failure to properly register the adaptec device.

The exit routine + call was added on July 30 by

	Commit: 55d9fcf57b
	Author: Matthew Wilcox
	Subject: [SCSI] dpt_i2o: convert to SCSI hotplug model.

Mathew: isn't a module exit routine a little too strong to be calling on the
failure of a single device?  Module exit implies that other, non-failing
adaptec raid devices will also get shut down.

Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:42 -04:00
Adrian Bunk
f01f9d5943 [SCSI] imm: fix check-after-use
The Coverity checker spotted that we have already oops'ed if "cmd"
was NULL.

Since "cmd" being NULL doesn't seem to be possible at this point this
patch removes the NULL check.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:33 -04:00
Andrew Morton
5975f643ef [SCSI] arcmsr: build fix
drivers/scsi/arcmsr/arcmsr_hba.c:129: error: 'arcmsr_pci_error_detected' undeclared here (not in a function)
drivers/scsi/arcmsr/arcmsr_hba.c:130: error: 'arcmsr_pci_slot_reset' undeclared here (not in a function)

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:29 -04:00
Adrian Bunk
774251ef64 [SCSI] nsp_cs: remove kernel 2.4 code
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:24 -04:00
Robert P. J. Day
a02676d4bd [SCSI] ibmmca: Remove dead references to MODULE_PARM macro
Remove the useless references to the obsolete MODULE_PARM macro.

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:17 -04:00
Matthew Wilcox
9d511a4b29 [SCSI] advansys: Changes to work on parisc
Change PortAddr to be an unsigned int instead of an unsigned short (IO
Port address are 24 bit on parisc).  Fix a couple of printk argument
warnings.  Remove the Kconfig marking as 'BROKEN'.

I haven't removed the #warning yet because virt_to_bus/bus_to_virt are
only eliminated for narrow boards.  Wide boards need more work.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:13 -04:00
Matthew Wilcox
d10fb2c7b5 [SCSI] advansys: Use dma mapping for overrun buffer
Convert the call to virt_to_bus() into a call to dma_map_single().  Some
architectures may require different DMA addresses for different devices,
so allocate one overrun buffer per host rather than one for all cards.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:05 -04:00
Matthew Wilcox
b249c7fda2 [SCSI] advansys: Remove a couple of uses of bus_to_virt
Replace ASC_VADDR_TO_U32 and ASC_U32_TO_VADDR with an auto-expanding
array that maps pointers to 32-bit IDs and back.  One of the uses of
ASC_VADDR_TO_U32 was in error; it should have been using ADV_VADDR_TO_U32.

Also replace the use of virt_to_bus when setting the sense_address with
a call to dma_map_single() followed by dma_cache_sync.  This part cribbed
from the 53c700 driver.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:54:00 -04:00
Matthew Wilcox
52c334e945 [SCSI] advansys: convert to use the data buffer accessors
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the parameters.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>

- convert the statistics to not distinguish between single and sg xfers
- replace ASC_CEILING with DIV_ROUND_UP
- remove an obsolete comment

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:56 -04:00
Matthew Wilcox
fd625f4705 [SCSI] advansys: Remove DvcGetPhyAddr
This rather complex function boiled down to calling virt_to_bus().
Also get rid of some obsolete defines and variables that could never vary.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:52 -04:00
Matthew Wilcox
98d41c29a4 [SCSI] advansys: Move a couple of fields from struct board to struct adv_dvc
board->carrp is a duplicate of asc_dvc->carrier_buf, so cut out the
middle-man and assign directly to carrier_buf.  Move orig_reqp to adv_dvc
too, since it's wide-board specific.  Also eliminate an unnecessary BUG_ON
(we'll never get there with a NULL carrier_buf, and will crash if we do).
The bulk of this patch is rearranging structures so everything's declared
in the right order.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:48 -04:00
Matthew Wilcox
afbb68c35f [SCSI] advansys: Make sdtr_period_tbl a pointer
It's somewhat neater to make this a pointer to one of two tables
than initialising an array in the driver.  Also delete the unused
AscSynIndexToPeriod and rename host_init_sdtr_index to min_sdtr_index

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:45 -04:00
Matthew Wilcox
9d0e96eba1 [SCSI] advansys: Get rid of board index number
It's always a mistake to have your own index of boards; just use the
scsi host number.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:41 -04:00
Matthew Wilcox
f092d2290f [SCSI] advansys: Remove private lock
The board lock was essentially identical with the host lock.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:37 -04:00
Matthew Wilcox
b352f92376 [SCSI] advansys: Sort out debug macros
Replace ASC_DBG{,1,2,3,4,5} with a single variadic macro ASC_DBG.  As
suggested by Jeff Garzik, include DRV_NAME and __FUNCTION__ in the output.
Change all callers to no longer include the function name in the string.

Enabling ADVANSYS_DEBUG to test this feature shows a lot of other problems
that need to be fixed:
 - Reorder asc_prt_* functions now that their prototypes have been removed.
 - There is no longer a struct device in ASC_DVC_CFG/ADV_DVC_CFG, and it
   wasn't necessarily a PCI device to begin with.  Print the bus_id from
   asc_board->dev instead.
 - isr_callback no longer exists.
 - ASC_DBG_PRT_SCSI_CMND isn't being used, so delete asc_prt_scsi_cmnd
   too.
 - A missing semicolon

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:34 -04:00
Matthew Wilcox
b08fc56550 [SCSI] advansys: Remove library version & serial numbers
With the ASC and ADV libraries merged into the driver, there really is
no point in reporting their version numbers, or even trying to maintain
them.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:29 -04:00
Matthew Wilcox
d241149558 [SCSI] advansys: Remove asc_board_t typedef and ASC_BOARDP macro
asc_board_t was simply a typedef for struct asc_board.  ASC_BOARDP()
can be replaced by shost_priv() except in the ASC_STATS* macros which
rely on the cast; add an explicit cast there.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:26 -04:00
Matthew Wilcox
720349a879 [SCSI] advansys: Merge ASC_IERR definitions
There were two blocks of ASC_IERR definitions; one for narrow and one for
wide boards.  Some of the same names were used (with the same values),
and some of the same values were used with different names.  This could
only lead to confusion, so I unified them in one block of definitions
with no overlapping values.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:22 -04:00
Matthew Wilcox
d361db4832 [SCSI] advansys: Sort out irq number mess
The interrupt number was being stored in 4-5 different places, each with
its own type, rules and usage.  Fix this by keeping an unsigned int in
the struct asc_board, and filling it in from the bus probe functions
(since it's different for each of the four bus types).  In order to do
this, we have to allocate the Scsi_Host in the bus probe functions too.
Then we can return an error from advansys_board_found, which requires
a little rearranging of code (and removing of the err_code variable).
Move the Wide Board flag setting into the PCI bus probe function.

Split the AscGetChipIRQ function into three functions (one for each bus
type that needs it) and add some commentary to explain what's going on.
Also get rid of the AscSetChipIRQ function as we only ever set the
interrupt number to the same value it already had.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:18 -04:00
Matthew Wilcox
9a256fa50e [SCSI] advansys: Remove ASC_WIDE_BOARD predicate
Replace it with !ASC_NARROW_BOARD

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:14 -04:00
Matthew Wilcox
ae002fec69 [SCSI] advansys: Remove ASC_SELECT_QUEUE_DEPTHS
It was only ever set; never tested, nor cleared.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:11 -04:00
Matthew Wilcox
52fa077709 [SCSI] advansys: Improve reset handler
- Don't need to set ASC_HOST_IN_RESET any more
 - Don't need to test scp->device->host for NULL -- if it's NULL, we
   couldn't've been called.
 - Use scmd_printk instead of ASC_PRINT

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:06 -04:00
Matthew Wilcox
05848b6e66 [SCSI] advansys: Fix simultaneous calls to ->queuecommand
The narrow board used two global structures to set up a command;
unfortunately they weren't locked, so with two boards in the machine,
one call to queuecommand could corrupt the data being used by the other
call to queuecommand.

Fix this by allocating asc_scsi_q on the stack (64 bytes) and using kmalloc
for the asc_sg_head (2k)

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:53:02 -04:00
Matthew Wilcox
41d2493d34 [SCSI] advansys: Restructure asc_execute_scsi_cmnd()
The wide and narrow boards share identical handling of the return value,
except for some trivial error messages.  Move the handling to the common
end of the function.  Also move variable declarations to the arms of
the `if' that they're used in and delete some pointless comments.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-10-12 14:52:59 -04:00