This patch:
- enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
- adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
present on following boards:
am43x-epos-evm:
On this board, NAND Flash control lines are muxed with QSPI, Thus only
one of the two can be used at a time. Selection is controlled by:
(a) dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
commit ac65caf514
ARM: OMAP2+: cleaned-up DT support of various ECC schemes
Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch has following updates, specific to MTD/NAND DT
- update MTD NAND partition table to keep compatibility between
different boards and mainline u-boot.
- prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
from other MTD device partitions (like NOR and QSPI)
Partition_Name Partition_Size
/dev/mtd0 NAND.SPL 1 block-size*
/dev/mtd1 NAND.SPL.backup1 1 block-size*
/dev/mtd2 NAND.SPL.backup2 1 block-size*
/dev/mtd3 NAND.SPL.backup3 1 block-size*
/dev/mtd5 NAND.u-boot-spl-os 2 block-size* [for falcon boot]
/dev/mtd4 NAND.u-boot 1 MB
/dev/mtd6 NAND.u-boot-env 1 block-size*
/dev/mtd7 NAND.u-boot-env.backup1 1 block-size*
/dev/mtd8 NAND.kernel till 0xA00000
/dev/mtd9 NAND.file-system till end of device
* am335x-evm uses NAND device with block-size=128KiB
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This requires vaux4.
Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds basic sound support for gta04 board.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gta04 using tcs2007 touchscreen. Add support for that.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds support for the bq24150a chip to the
Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds support for the isp1704 chip to the Nokia N900
DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds support for the N900's headphone
amplifier to the N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add support for tsl2563 light sensor to the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add Keyboard Matrix information to N900's DTS file.
This patch maps the keys exactly as the original
board code.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add keypad node to twl4030, so that board DTS
files can just add the keymap.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
MMC 8 bit mode operation depends on dip switch setting which is not
obvious - The current board file has this description. However, with
removal of the board file in the future, this information will be lost
and has to be rediscovered.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Craneboard is a hardware development platform based on the Sitara
AM3517 ARM Cortex - A8 microprocessor device - see [1] for more
details. Add basic devices for craneboard as replacement for the board
file scheduled for removal as part of device tree conversion
[1] http://craneboard.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The pmu is needed to bring up the cores during smp operations and later
also other system parts. Therefore add a node and documentation for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
Add dt-nodes for the sram on rk3066 and rk3188 including the reserved section
needed for smp bringup.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
This adds the device-node and config select to enable the
scu in all Rockchip Cortex-A9 SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
Enable second USB channel and set it into 'host' mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Making it possible to reference and therefor change (disable) this
device node from other dts file which import this dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing interrupt properties to the ecap0, ecap1, and ecap2
nodes.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP34xx, AM3517 and OMAP36xx platforms use dpll1 clock.
OMAP443x, OMAP446x, OMAP447x, OMAP5, DRA7, AM43xx platforms use
dpll_mpu clock.
Latency used is the generic latency defined in omap-cpufreq
driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INCOstartec LILLY-DBB056 is a carrier board (baseboard) for
computer-on-module LILLY-A83X.
This patch adds device-tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.
This patch adds device tree support for most of its features.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: Tony Lindgren <tony@atomide.com>
In omap2420.dtsi and omap2430.dtsi disable all mcbsp nodes and board dts
files can explicitly enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In omap3.dtsi disable all mcbsp nodes and board dts files can explicitly
enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board dts files will need to enable the IP nodes which they are using and
does not have to care about the not used ones (to disable them).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcbsp2, dmic, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the hwspinlock device tree node for AM43xx family
of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a new generic property "#hwlock-cells" to the hwspinlock
DT nodes on OMAP4, OMAP5 and AM33xx. This common property allows
different platform implementations to define the args specifier
length. OMAP implementations will always use a value of 1.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3517 CoM and SBC-T3517 board.
reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):
* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led
Added basic support for:
* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T3530 CoM and SBC-T3530 board.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
