There is currently only one way for userspace to say "wait for my storage
device to get ready for the modules I just loaded": to load the
scsi_wait_scan module. Expectations of userspace are that once this
module is loaded, all the (storage) devices for which the drivers
were loaded before the module load are present.
Now, there are some issues with the implementation, and the async
stuff got caught in the middle of this: The existing code only
waits for the scsy async probing to finish, but it did not take
into account at all that probing might not have begun yet.
(Russell ran into this problem on his computer and the fix works for him)
This patch fixes this more thoroughly than the previous "fix", which
had some bad side effects (namely, for kernel code that wanted to wait for
the scsi scan it would also do an async sync, which would deadlock if you did
it from async context already.. there's a report about that on lkml):
The patch makes the module first wait for all device driver probes, and then it
will wait for the scsi parallel scan to finish.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a comment typo in slow-work.h
...a trivial mistake, but it will mess up kerneldoc if nothing else.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Collect the DECLARE/DEFINE declarations together in linux/percpu-defs.h so
that they're in one place, and give them descriptive comments, particularly
the SHARED_ALIGNED variant.
It would be nice to collect these in linux/percpu.h, but that's not possible
without sorting out the severe #include recursion between the x86 arch headers
and the general headers (and possibly other arches too).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In non-SMP mode, the variable section attribute specified by DECLARE_PER_CPU()
does not agree with that specified by DEFINE_PER_CPU(). This means that
architectures that have a small data section references relative to a base
register may throw up linkage errors due to too great a displacement between
where the base register points and the per-CPU variable.
On FRV, the .h declaration says that the variable is in the .sdata section, but
the .c definition says it's actually in the .data section. The linker throws
up the following errors:
kernel/built-in.o: In function `release_task':
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
To fix this, DECLARE_PER_CPU() should simply apply the same section attribute
as does DEFINE_PER_CPU(). However, this is made slightly more complex by
virtue of the fact that there are several variants on DEFINE, so these need to
be matched by variants on DECLARE.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This had been delayed for some time due to failure to work on the one piece
of G41 hardware we had, and lack of success reports from anybody else.
Current hardware appears to be OK.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
[anholt: hand-applied due to conflicts with IGD patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is a doc-only patch which I hope will reduce the number of
spi_master controller driver patches starting out with a common
implementation bug.
(As in: almost every spi_master driver I see starts out with its
version of this bug. Sigh.)
It just re-emphasizes that the setup() method may be called for one
device while a transfer is active on another ... which means that most
driver implementations shouldn't touch any registers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable userspace to receive messages that a BMC transmits using an OEM
medium. This is used by the HP iLO2.
Based on code originally written by Patrick Schoeller.
Signed-off-by: dann frazier <dannf@hp.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IPMI driver would attempt to use the event buffer even if that
didn't exist on the BMC. This patch modified the IPMI driver to check
for the event buffer's existence before trying to use it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add enable() and disable() callbacks for clocksources.
This allows us to put unused clocksources in power save mode. The
functions clocksource_enable() and clocksource_disable() wrap the
callbacks and are inserted in the timekeeping code to enable before use
and disable after switching to a new clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
reiserfs: fix j_last_flush_trans_id type
fs: Mark get_filesystem_list() as __init function.
kill vfs_stat_fd / vfs_lstat_fd
Separate out common fstatat code into vfs_fstatat
ecryptfs: use memdup_user()
ncpfs: use memdup_user()
xfs: use memdup_user()
sysfs: use memdup_user()
btrfs: use memdup_user()
xattr: use memdup_user()
autofs4: use memchr() in invalid_string()
Documentation/filesystems: remove out of date reference to BKL being held
Fix i_mutex vs. readdir handling in nfsd
fs/compat_ioctl: fix build when !BLOCK
Fix autofs_expire()
No need for crossing to mountpoint in audit_tag_tree()
Safer nfsd_cross_mnt()
Touch all affected namespaces on propagation of mount
Fix AUTOFS_DEV_IOCTL_REQUESTER_CMD
Older MIPS assembler don't support .set for defining aliases.
Using = works for old and new assembers.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
aio_write gets const struct iovec * but tun_chr_aio_write casts this to struct
iovec * and modifies the iovec. As a result, attempts to use io_submit
to send packets to a tun device fail with weird errors such as EINVAL.
Since tun is the only user of skb_copy_datagram_from_iovec, we can
fix this simply by changing the later so that it does not
touch the iovec passed to it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's an skb_copy_datagram_iovec() to copy out of a paged skb,
but it modifies the iovec, and does not support starting
at an offset in the destination. We want both in tun.c, so let's
add the function.
It's a carbon copy of skb_copy_datagram_iovec() with enough changes to
be annoying.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
because of using the same function get_ethernet_addr as cdc_ether.c
i export usbnet_get_ethernet_addr from usbnet and fixed cdc_ether
(suggested by Oliver Neukum).
Signed-off-by: Peter Holik <peter@holik.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conversion in commit 600ed41675 had missed
that one, but converted format from %lu to %u. As the result,
/proc/..../journal got buggered on 64bit boxen.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
"int get_filesystem_list(char * buf)" is called by only
"static void __init get_fs_names(char *page)".
We can mark get_filesystem_list() as "__init".
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There's really no reason to keep vfs_stat_fd and vfs_lstat_fd with
Oleg's vfs_fstatat. Use vfs_fstatat for the few cases having the
directory fd, and switch all others to vfs_stat / vfs_lstat.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is a version incorporating Christoph's suggestion.
Separate out common *fstatat functionality into a single function
instead of duplicating it all over the code.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This function was left orphan by the latest round of sw-counter
cleanups.
[ Impact: remove unused kernel function ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to a cut and paste error, the trace_seq_putc had a semicolon
after the prototype but before the stub function when tracing is
disabled.
[Impact: fix compile error ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
last_synq_overflow eats 4 or 8 bytes in struct tcp_sock, even
though it is only used when a listening sockets syn queue
is full.
We can (ab)use rx_opt.ts_recent_stamp to store the same information;
it is not used otherwise as long as a socket is in listen state.
Move linger2 around to avoid splitting struct mtu_probe
across cacheline boundary on 32 bit arches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 900af0d973 (PM: Change suspend
code ordering) changed the ordering of suspend code in such a way
that the platform .prepare() callback is now executed after the
device drivers' late suspend callbacks have run. Unfortunately, this
turns out to break ARM platforms that need to talk via I2C to power
control devices during the .prepare() callback.
For this reason introduce two new platform suspend callbacks,
.prepare_late() and .wake(), that will be called just prior to
disabling non-boot CPUs and right after bringing them back on line,
respectively, and use them instead of .prepare() and .finish() for
ACPI suspend. Make the PM core execute the .prepare() and .finish()
platform suspend callbacks where they were executed previously (that
is, right after calling the regular suspend methods provided by
device drivers and right before executing their regular resume
methods, respectively).
It is not necessary to make analogous changes to the hibernation
code and data structures at the moment, because they are only used
by ACPI platforms.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Len Brown <len.brown@intel.com>
<linux/seccomp.h> uses EINVAL so should include <linux/errno.h>. This
fixes a build error on 64-bit MIPS if CONFIG_SECCOMP is disabled.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, when x2apic is not enabled, interrupt remapping
will be enabled in init_dmars(), where it is too late to remap
ioapic interrupts, that is, ioapic interrupts are really in
compatibility mode, not remappable mode.
This patch always enables interrupt remapping before ioapic
setup, it guarantees all interrupts will be remapped when
interrupt remapping is enabled. Thus it doesn't need to set
the compatibility interrupt bit.
[ Impact: refactor intr-remap init sequence, enable fuller remap mode ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: allen.m.kay@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1239957736-6161-4-git-send-email-weidong.han@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to a cut and paste error, I added the gcc attribute for printf
format to the static inline stub of trace_seq_printf.
This will cause a compile failure.
[ Impact: fix compiler error when CONFIG_TRACING is off ]
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: =?ISO-8859-15?Q?Fr=E9d=E9ric_Weisbecker?= <fweisbec@gmail.com>
LKML-Reference: <alpine.DEB.2.00.0904171717080.1016@gandalf.stny.rr.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
UIO: fix specific device driver missing statement for depmod
Driver core: remove pr_fmt() from dynamic_dev_dbg() printk
driver core: prevent device_for_each_child from oopsing
dynamic debug: resurrect old pr_debug() semantics as pr_devel()
Driver Core: early platform driver
proc: mounts_poll() make consistent to mdstat_poll
sysfs: sysfs poll keep the poll rule of regular file.
driver core: allow non-root users to listen to uevents
driver core: fix driver_match_device
sysfs: don't use global workqueue in sysfs_schedule_callback()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
WUSB: correct format of wusb_chid sysfs file
WUSB: fix oops when completing URBs for disconnected devices
WUSB: disconnect all devices when stopping a WUSB HCD
USB: whci-hcd: check return value of usb_hcd_link_urb_to_ep()
USB: whci-hcd: provide a endpoint_reset method
USB: add reset endpoint operations
USB device codes for Motorola phone.
usb-storage: fix mistake in Makefile
USB: usb-serial ch341: support for DTR/RTS/CTS
Revert USB: usb-serial ch341: support for DTR/RTS/CTS
USB: musb: fix possible panic while resuming
USB: musb: fix isochronous TXDMA (take 2)
USB: musb: sanitize clearing TXCSR DMA bits (take 2)
USB: musb: bugfixes for multi-packet TXDMA support
USB: musb_host, fix ep0 fifo flushing
USB: usb-storage: augment unusual_devs entry for Simple Tech/Datafab
USB: musb_host, minor enqueue locking fix (v2)
USB: fix oops in cdc-wdm in case of malformed descriptors
USB: qcserial: Add extra device IDs
USB: option: Add ids for D-Link DWM-652 3.5G modem
...
The i915 DRM triggers registration of the ACPI video driver on load. It
should unregister it at unload in order to avoid generating backtraces on
being reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The tracing infrastructure allows for recursion. That is, an interrupt
may interrupt the act of tracing an event, and that interrupt may very well
perform its own trace. This is a recursive trace, and is fine to do.
The problem arises when there is a bug, and the utility doing the trace
calls something that recurses back into the tracer. This recursion is not
caused by an external event like an interrupt, but by code that is not
expected to recurse. The result could be a lockup.
This patch adds a bitmask to the task structure that keeps track
of the trace recursion. To find the interrupt depth, the following
algorithm is used:
level = hardirq_count() + softirq_count() + in_nmi;
Here, level will be the depth of interrutps and softirqs, and even handles
the nmi. Then the corresponding bit is set in the recursion bitmask.
If the bit was already set, we know we had a recursion at the same level
and we warn about it and fail the writing to the buffer.
After the data has been committed to the buffer, we clear the bit.
No atomics are needed. The only races are with interrupts and they reset
the bitmask before returning anywy.
[ Impact: detect same irq level trace recursion ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The CONFIG_EVENT_TRACER is the way to turn on event tracing when no
other tracing has been configured. All code to get enabled should
depend on CONFIG_EVENT_TRACING. That is what is enabled when TRACING
(or CONFIG_EVENT_TRACER) is selected.
This patch enables the include/trace/ftrace.h file when
CONFIG_EVENT_TRACING is enabled.
[ Impact: fix warning in event tracer selftest ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This renames include/asm-h8300/timer.h into arch/h8300/include/asm: it
was left over just because that file had been created in the -mm tree
before the whole h8300 header subdirectory had been moved, and then got
merged in the old location afterwards.
(See commits e0b0f9e4ea: "h8300: update
timer handler - new files" and 758db3f211:
"[h8300] move include/asm-h8300 to arch/h8300/include/asm" for details).
This also removes a left-over .gitignore file in include/asm-arm that
became stale when the ARM header files were moved (which happened in
multiple commits, just see "git log -- include/asm-arm" for details).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: move include/asm-m32r/* to arch/m32r/include/asm/
m32r: move include/asm-m32r headers to arch/m32r/include/asm
kmem_event_types.h is no longer necessary since tracepoint definitions
are put into include/trace/events/kmem.h
[ Impact: remove now-unused file. ]
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <49E7EF37.2080205@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
