__pa() was used by virt_to_page() and virt_addr_valid(). These
latter are used when kernel is initialised so __pa() is not
appropriate, we use virt_to_phys() instead.
Futhermore __pa() is going to take care of CKSEG0/XKPHYS
address mix for 64 bit kernels. This makes __pa() more complex
than virt_to_phys() and this extra work is not needed by
virt_to_page() and virt_addr_valid().
Eventually it consolidates virt_to_phys() prototype by making
its argument 'const'. this avoids some warnings that was due
to some virt_to_page() usages which pass const pointer.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ib_cm_establish() function is replaced with a more generic
ib_cm_notify(). This routine is used to notify the CM that failover
has occurred, so that future CM messages (LAP, DREQ) reach the remote
CM. (Currently, we continue to use the original path) This bumps the
userspace CM ABI.
New alternate path information is captured when a LAP message is sent
or received. This allows QP attributes to be initialized for the user
when a new path is loaded after failover occurs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move declaration of struct pxa2xx_udc_mach_info from
include/asm-arm/arch-pxa/udc.h to new file
include/asm-arm/mach/udc_pxa2xx.h.
This allow us to use this structure with
multiple platforms - pxa and ixp4xx. USB
device controller used in pxa25x is the same
as controller used in ixp4xx.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds get_device() and put_device() methods to the MTD description
structure (struct mtd_info). These methods are called by MTD whenever the MTD
device is get or put. They are needed when the underlying driver is something
smarter then just flash chip driver, for example UBI.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
This patch adds one more function to the MTD interface to make it possible to
open MTD devices by their names, not only numbers. This is very handy in many
situations. Also, MTD device number depend on load order and may vary, while
names are fixed.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
MAX_HEADER is either set to LL_MAX_HEADER or LL_MAX_HEADER + 48, and
this is controlled by a set of CONFIG_* ifdef tests.
It is trying to use LL_MAX_HEADER + 48 when any of the tunnels are
enabled which set hard_header_len like this:
dev->hard_header_len = LL_MAX_HEADER + sizeof(struct xxx);
The correct set of tunnel drivers which do this are:
ipip
ip_gre
ip6_tunnel
sit
so make the ifdef test match.
Noticed by Patrick McHardy and with help from Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Use stricter in process stack check for unwinder
[PATCH] i386: Fix compilation with UP genericarch
[PATCH] x86-64: Fix warning in io_apic.c
[PATCH] x86-64: work around gcc4 issue with -Os in Dwarf2 stack unwind
[PATCH] x86_64: Align data segment to PAGE_SIZE boundary
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa:
[ALSA] version 1.0.13
[ALSA] snd-emu10k1: Fix capture for one variant.
[ALSA] Fix hang-up at disconnection of usb-audio
[ALSA] hda: fix typo for xw4400 PCI sub-ID
[ALSA] hda: fix sigmatel dell system detection
[ALSA] Enable stereo line input for TAS codec
[ALSA] rtctimer: handle RTC interrupts with a tasklet
include/scsi/libsas.h:479: error: field 'smp_req' has incomplete type
include/scsi/libsas.h:480: error: field 'smp_resp' has incomplete type
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As was discussed between Ricard Wanderlöf, David Woodhouse, Artem
Bityutskiy and me, the current API for reading/writing OOB is confusing.
The thing that introduces confusion is the need to specify ops.len
together with ops.ooblen for reads/writes that concern only OOB not data
area. So, ops.len is overloaded: when ops.datbuf != NULL it serves to
specify the length of the data read, and when ops.datbuf == NULL, it
serves to specify the full OOB read length.
The patch inlined below is the slightly updated version of the previous
patch serving the same purpose, but with the new Artem's comments taken
into account.
Artem, BTW, thanks a lot for your valuable input!
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Currently, mtd_blkdevs enforces a block size of 512, even if the drivers
can seemingly request a different size. This patch fixes mtd_blkdevs so
block sizes other than 512 work correctly.
Signed-off-by: Richard Purdie <rpurdie@openedhand.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix
arch/i386/mach-generic/built-in.o: In function `apicid_to_node':
summit.c:(.text+0x2f): undefined reference to `apicid_2_node'
with CONFIG_GENERICH_ARCH and !CONFIG_SMP
Signed-off-by: Andi Kleen <ak@suse.de>
You wouldn't think that doing an ALIGN() macro that aligns something up
to a power-of-two boundary would be likely to have bugs, would you?
But hey, in the wonderful world of mixing integer types, you have to be
careful. This just makes sure that the alignment is interpreted in the
same type as the thing to be aligned.
Thanks to Roland Dreier, who noticed that the amso1100 driver got broken
by the previous fix (that just extended the mask to "unsigned long", but
was still broken in "unsigned long long" - it just happened to be the
same on 64-bit architectures).
See commit 4c8bd7eeee for the history of
bugs here...
Acked-by: Roland Dreier <rdreier@cisco.com>
Cc: Andrew Morton <akpm@osdl.org>
Cc: David Miller <davem@davemloft.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I still think using BUILD_BUG_ON() is unacceptable, especially given how
vague the error message was.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
[ And I already removed gthe BUILD_BUG_ON() in the previous commit ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit ee3ce191e8, since it
broke on at least ARM, MIPS and PA-RISC due to complicated header file
dependencies.
Conflicts in include/linux/spinlock.h (due to the "nested" variety
fixes) fixed up by hand.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restoring old, correct comment for sk_filter_release, moving it to
where it should actually be, and changing new comment into proper
comment for sk_filter_rcu_free, where it actually makes sense.
The original fix submitted for this on Oct 23 mistakenly documented
the wrong function.
Signed-off-by: Paul Bonser <misterpib@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it break or warn if you pass to spin_lock_irqsave() and friends
something different from "unsigned long flags;". Suprisingly large amount
of these was caught by recent commit
c53421b18f and others.
Idea is largely from FRV typechecking. Suggestions from Andrew Morton.
All stupid typos in first version fixed.
Passes allmodconfig on i386, x86_64, alpha, arm as well as my usual config.
Note #1: checking with sparse is still needed, because a driver can save
and pass around flags or something. So far patch is very intrusive.
Note #2: techically, we should break only if
sizeof(flags) < sizeof(unsigned long),
however, the more pain for getting suspicious code into kernel,
the better.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The user-space daemon and tgt kernel module need bi-directional
kernel/user high-performance interface, however, mainline provides no
standard interface like that.
This patch adds shared memory interface between kernel and user spaces
like some other drivers do by using own character device. The
user-space daemon and tgt kernel module creates shared memory via mmap
and use it like ring buffer. poll (kernel to user) and write (user to
kernel) system calls are used for notification.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The core scsi target lib functions.
TODO:
- mv md/dm-bio-list.h to linux/bio-list.h so md and us do not have to
do that weird include.
- convert scsi_tgt_cmd's work struct to James's execute code. And try
to kill our scsi_tgt_cmd.
- add host state checking. We do refcouting so hotplug is partially
supported, but we need to add state checking to make it easier on
the LLD.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the needed changes to the scsi-ml for the target
mode support.
Note, per the last review we moved almost all the fields we added
to the scsi_cmnd to our internal data structure which we are going
to try and kill off when we can replace it with support from other
parts of the kernel.
The one field we left on was the offset variable. This is needed to handle
the case where the target gets request that is so large that it cannot
execute it in one dma operation. So max_secotors or a segment limit may
limit the size of the transfer. In this case our tgt core code will
break up the command into managable transfers and send them to the
LLD one at a time. The offset is then used to tell the LLD where in
the command we are at. Is there another field on the scsi_cmd for
that?
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add input subsystem to kernel-api docbook.
Enhance some function and parameter comments.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Perform actual driver registration right in serio_register_driver()
instead of offloading it to kseriod and return proper error code to
callers if driver registration fails.
Note that driver <-> port matching is still done by kseriod to
speed up boot process since probing for PS/2 mice and keyboards
is pretty slow.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3941/1: [Jornada7xx] - Addition to MAINTAINERS
[ARM] 3942/1: ARM: comment: consistent_sync should not be called directly
[ARM] ebsa110: fix warnings generated by asm/arch/io.h
[ARM] 3933/1: Source drivers/ata/Kconfig
The Au1xx IDE controller driver doesn't compile:
CC drivers/ide/mips/au1xxx-ide.o
/linux-2.6.19-rc6-work/drivers/ide/mips/au1xxx-ide.c:480: error: conflicting types for 'auide_ddma_tx_callback'
include2/asm/mach-au1x00/au1xxx_ide.h:174: error: previous declaration of 'auide_ddma_tx_callback' was here
/linux-2.6.19-rc6-work/drivers/ide/mips/au1xxx-ide.c:486: error: conflicting types for 'auide_ddma_rx_callback'
include2/asm/mach-au1x00/au1xxx_ide.h:176: error: previous declaration of 'auide_ddma_rx_callback' was here
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
/*
* Note: Drivers should NOT use this function directly, as it will break
* platforms with CONFIG_DMABOUNCE.
* Use the driver DMA support - see dma-mapping.h (dma_sync_*)
*/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a driver can find its own targets, it can now fill in scan_finished and
(optionally) scan_start in the scsi_host_template. Then, when it calls
scsi_scan_host(), it will be called back (from a thread if asynchronous
discovery is enabled), first to start the scan, and then at intervals to
check if the scan is completed.
Also make scsi_prep_async_scan and scsi_finish_async_scan static.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch implements a REQ_DEVICE_RESET handler for the aic94xx
driver. Like the earlier REQ_TASK_ABORT patch, this patch defers the
device reset to the Scsi_Host's workqueue, which has the added benefit
of ensuring that the device reset does not happen at the same time
that the abort tmfs are being processed. After the phy reset, the
busted drive should go away and be re-detected later, which is indeed
what I've seen on both a x260 and a x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
Reclaim a word from the size of the work_struct by folding the pending bit and
the wq_data pointer together. This shouldn't cause misalignment problems as
all pointers should be at least 4-byte aligned.
Signed-Off-By: David Howells <dhowells@redhat.com>
Define a type for the work function prototype. It's not only kept in the
work_struct struct, it's also passed as an argument to several functions.
This makes it easier to change it.
Signed-Off-By: David Howells <dhowells@redhat.com>
Separate delayable work items from non-delayable work items be splitting them
into a separate structure (delayed_work), which incorporates a work_struct and
the timer_list removed from work_struct.
The work_struct struct is huge, and this limits it's usefulness. On a 64-bit
architecture it's nearly 100 bytes in size. This reduces that by half for the
non-delayable type of event.
Signed-Off-By: David Howells <dhowells@redhat.com>
The IGMPV3_EXP() macro doesn't correctly shift the normalization bit, so
time-out values are longer than they should be.
Thanks to Dirk Ooms for finding the problem in IGMPv3 - MLDv2 had a
similar problem that was already fixed a year ago. :-(
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a quick hack to overcome the fact that SRCU currently does not
allow static initializers, and we need to sometimes initialize those
things before any other initializers (even "core" ones) can do so.
Currently we don't allow this at all for modules, and the only user that
needs is right now is cpufreq. As reported by Thomas Gleixner:
"Commit b4dfdbb3c7 ("[PATCH] cpufreq:
make the transition_notifier chain use SRCU breaks cpu frequency
notification users, which register the callback > on core_init
level."
Cc: Thomas Gleixner <tglx@timesys.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>,
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch to using irq_handler_t for interrupt function handler pointers.
Change name of m68knommu's irq_hanlder_t data structure so it doesn't
clash with the common type (include/linux/interrupt.h).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove two warnings:
drivers/serial/8250_early.c:136: warning: unused variable 'mapsize'
include/linux/io.h:47: warning: passing argument 1 of '__readb' discards qualifiers from pointer target type
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch has removed one too many semicolon in crypto.h.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Disable TSO on 5906 if CLKREQ is enabled.
[TCP]: Fix up sysctl_tcp_mem initialization.
[NETFILTER]: ip6_tables: use correct nexthdr value in ipv6_find_hdr()
[NETFILTER]: ip6_tables: fixed conflicted optname for getsockopt
[NETFILTER]: Use pskb_trim in {ip,ip6,nfnetlink}_queue
[NETFILTER]: nfnetlink_log: fix byteorder of NFULA_SEQ_GLOBAL
[TG3]: Increase 5906 firmware poll time.
This adds fat_getattr() for setting stat->blksize. (FAT uses the size
of cluster for proper I/O)
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
