Use raw_smp_processor_id() instead of get_cpu() as we don't need the
extra features of get_cpu().
Signed-off-by: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The logic that decides that a fork() might be able to avoid copying a VM
area when it can be re-created by page faults didn't know about the new
vm_insert_page() case.
Also make some things a bit more anal wrt VM_PFNMAP.
Pointed out by Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The udelay() inline for ia64 uses the ITC. If CONFIG_PREEMPT is enabled
and the platform has unsynchronized ITCs and the calling task migrates
to another CPU while doing the udelay loop, then the effective delay may
be too short or very, very long.
This patch disables preemption around 100 usec chunks of the overall
desired udelay time. This minimizes preemption-holdoffs.
udelay() is now too big to be inline, move it out of line and export it.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This update now allows this driver to be used on big endian bus
machines that aren't parisc. To do that, the driver must set a
CONFIG_53C700_BE_BUS in Kconfig to compile the right macro versions.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This finally fixes the radeon memory mapping bug that was incorrectly
fixed by the previous patch. This time, we use the actual vram size as
the size to calculate how far to move the AGP aperture from the
framebuffer in card's memory space.
If there are still issues with this patch, they are due to bugs in the X
driver that I'm working on fixing too.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the scenario that a link was broken, the devloss timer for each
rport was expire at roughly the same time, causing lots of "delete"
workqueue items being queued. Depth is dependent upon the number of
rports that were on the link.
The rport target remove calls were calling flush_scheduled_work(),
which would interrupt the stream, and start the next workqueue item,
which did the same thing, and so on until recursion depth was large.
This fix stops the recursion in the initial delete path, and pushes it
off to a host-level work item that reaps the dead rports.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce a new helper, print_nego() to handle SDTR/WDTR/PPR.
Split out the guts of show_spi_transport_period_helper() into period_to_str()
and use it in print_nego to get the period factor conversion right.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace the custom NO_*_MSGS definitions with uses of ARRAY_SIZE.
This fixes a bug in the definition of NO_EXTENDED_MSGS.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A missing comma meant that "Ordered Queue Tag" and "Ignore Wide Residue"
were being concatenated together.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_print_msg() is an SPI-specific concept. This patch moves it from
constants.c to scsi_transport_spi.c and updates the Kconfig to link in
the SPI class for the drivers which use scsi_print_msg().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Kai minus last sg_segs clearing which was merged already.
> > Was there a oops or lockup or any debug output you can send me? I will try
> > some more large request tests with scsi_debug. You also have to compile your
> > kernel with SCSI_MAX_PHYS_SEGMENTS == 255 to get larger requests now.
>
It was an oops in sgl_unmap_user_pages(). The reason is this:
/* XXX: just for debug. Remove when PageReserved is removed */
BUG_ON(PageReserved(page));
I was using /dev/zero as input and it triggers this. When I used a file as
input, this did not trigger. Should this BUG_ON be removed?
In the same log I noticed that there was another ->sg_segs inconsistency.
Also, the field ->last_SRpnt was not reset when scsi_execute_async()
failed. This caused the error message "Async command already active"
later and prevented proper close.
While doing the changes, I noticed that the current code (since
2.6.0-test4) does not set the pages dirty when reading with direct i/o.
All of these st problems (including the one I sent earlier) are fixed in
the patch at the end of this message. These fixes should probably be
included already in 2.6.15.
After these fixes, the tape seems to operate as expected. Without other
changes, the largest block size with sym53c896 SCSI adapter is 384 kB. The
maximum number of sg segments is set to 96 and clustering is disabled in
the driver. 96 x 4 kB = 384 kB. OK.
I enabled clustering and set max_sectors to 10000 in the SCSI HBA driver.
Now the block size limit is 5000 kB as expected.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- export __blk_put_request and blk_execute_rq_nowait
needed for async REQ_BLOCK_PC requests
- seperate max_hw_sectors and max_sectors for block/scsi_ioctl.c and
SG_IO bio.c helpers per Jens's last comments. Since block/scsi_ioctl.c SG_IO was
already testing against max_sectors and SCSI-ml was setting max_sectors and
max_hw_sectors to the same value this does not change any scsi SG_IO behavior. It only
prepares ll_rw_blk.c, scsi_ioctl.c and bio.c for when SCSI-ml begins to set
a valid max_hw_sectors for all LLDs. Today if a LLD does not set it
SCSI-ml sets it to a safe default and some LLDs set it to a artificial low
value to overcome memory and feedback issues.
Note: Since we now cap max_sectors to BLK_DEF_MAX_SECTORS, which is 1024,
drivers that used to call blk_queue_max_sectors with a large value of
max_sectors will now see the fs requests capped to BLK_DEF_MAX_SECTORS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have found some issues with Au1550 AC'97 OSS driver in 2.6
(sound/oss/au1550_ac97.c), though it also should concern 2.4 driver
(drivers/sound/au1550_psc.c).
start_dac() grabs a spinlock already held by its caller, au1550_write().
This doesn't show up with the standard UP spinlock impelmentation but when
the different one (mutex based) is in use, a lockup happens.
And the interrupt handlers also didn't grab the spinlock -- that's OK in
the usual kernel but not when the IRQ handlers are threaded. So, they're
grabbing the spinlock now (as every correct interrupt handler should do).
Signed-off-by: Konstantin Baidarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can't export a static struct to modules.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While doing some testing I discovered that if the BIOS on a board does not
properly setup the DMI information it leads to a panic in the IPMI code.
The panic is due to dereferencing a pointer which is not initialized. The
pointer is initialized in port_setup() and/or mem_setup() and used in
init_one_smi() and cleanup_one_si(), however if either port_setup() or
mem_setup() return ENODEV the pointer does not get initialized.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
convert st to always send scatterlists and kill scsi_request
usage.
This is the same as last time as it was posted, but with Kai's patches
merged and we now pass the bytes value to scsi_execute_async.
TODO:
- move DIO code to common place or make block layers usable for ULDs.
- move buffer allocation code to common place for all ULDs to use. And
make buffer allocation code handle all queue limits so we can find
out about problems before calling scsi_execute_async.
- move indirect (copy_to/from_user) paths commone place or make block
layers usable for ULDs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
