When probing devices-in-package for a c45 phy, device zero is the last
device to probe, however, if driver reads 0 from device zero,
c45_ids->devices_in_package is set to '0', the loop condition of probing
will be matched again, see codes below:
for (i = 1;i < num_ids && c45_ids->devices_in_package == 0;i++)
driver will run in a dead loop.
This patch restructures the bug and confusing loop, it provides a helper
function get_phy_c45_devs_in_pkg which to read devices-in-package registers
of a MMD, and rewrites the loop with using the helper function.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some netdev features, which when disabled on an upper device,
such as a bonding master or a bridge, must be disabled and cannot be
re-enabled on underlying devices.
This is a rework of an earlier more heavy-handed appraoch, which simply
disables and prevents re-enabling of netdev features listed in a new
define in include/net/netdev_features.h, NETIF_F_UPPER_DISABLES. Any upper
device that disables a flag in that feature mask, the disabling will
propagate down the stack, and any lower device that has any upper device
with one of those flags disabled should not be able to enable said flag.
Initially, only LRO is included for proof of concept, and because this
code effectively does the same thing as dev_disable_lro(), though it will
also activate from the ethtool path, which was one of the goals here.
[root@dell-per730-01 ~]# ethtool -k bond0 |grep large
large-receive-offload: on
[root@dell-per730-01 ~]# ethtool -k p5p1 |grep large
large-receive-offload: on
[root@dell-per730-01 ~]# ethtool -K bond0 lro off
[root@dell-per730-01 ~]# ethtool -k bond0 |grep large
large-receive-offload: off
[root@dell-per730-01 ~]# ethtool -k p5p1 |grep large
large-receive-offload: off
dmesg dump:
[ 1033.277986] bond0: Disabling feature 0x0000000000008000 on lower dev p5p2.
[ 1034.067949] bnx2x 0000:06:00.1 p5p2: using MSI-X IRQs: sp 74 fp[0] 76 ... fp[7] 83
[ 1034.753612] bond0: Disabling feature 0x0000000000008000 on lower dev p5p1.
[ 1035.591019] bnx2x 0000:06:00.0 p5p1: using MSI-X IRQs: sp 62 fp[0] 64 ... fp[7] 71
This has been successfully tested with bnx2x, qlcnic and netxen network
cards as slaves in a bond interface. Turning LRO on or off on the master
also turns it on or off on each of the slaves, new slaves are added with
LRO in the same state as the master, and LRO can't be toggled on the
slaves.
Also, this should largely remove the need for dev_disable_lro(), and most,
if not all, of its call sites can be replaced by simply making sure
NETIF_F_LRO isn't included in the relevant device's feature flags.
Note that this patch is driven by bug reports from users saying it was
confusing that bonds and slaves had different settings for the same
features, and while it won't be 100% in sync if a lower device doesn't
support a feature like LRO, I think this is a good step in the right
direction.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Nikolay Aleksandrov <razor@blackwall.org>
CC: Michal Kubecek <mkubecek@suse.cz>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IP stack passes SKBs the sfc driver puts them in 2 different TX
queues (called partners), one for checksummed and one for not checksummed.
If the SKB has xmit_more set the driver will delay pushing the work to the
NIC.
When later it does decide to push the buffers this patch ensures it also
pushes the partner queue, if that also has any delayed work. Before this
fix the work in the partner queue would be left for a long time and cause
a netdev watchdog.
Fixes: 70b33fb ("sfc: add support for skb->xmit_more")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the RX descriptor 0 bit 30 is RDLE (receive descriptor
list end), not RDEL.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sit0 device allocates its percpu storage twice :
- One time in ipip6_tunnel_init()
- One time in ipip6_fb_tunnel_init()
Thus we leak 48 bytes per possible cpu per network namespace dismantle.
ipip6_fb_tunnel_init() can be much simpler and does not
return an error, and should be called after register_netdev()
Note that ipip6_tunnel_clone_6rd() also needs to be called
after register_netdev() (calling ipip6_tunnel_init())
Fixes: ebe084aafb ("sit: Use ipip6_tunnel_init as the ndo_init function.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar says:
====================
re-org actor admin/oper key updates
I was observing machines entering into weird LACP state when the
partner is in passive mode. This issue is not because of the partners
in passive state but probably because of some operational key update
which is pushing the state-machine is that weird state. This was
happening randomly on about 1% of the machine (when the sample size
is a large set of machines with a variety of NICs/ports bonded).
In this patch-series I'm attempting to unify the logic of actor-key
/ operational-key changes to one place to avoid possible errors in
update. Also this eliminates the need for the event-handler to decide
if the key needs update.
After this patch-set none of the machines (from same sample set) were
exhibiting LACP-weirdness that was observed earlier.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Old logic of updating state-machine is not required since
ad_update_actor_keys() does it implicitly. The only loss is
the notification differentiation between speed vs. duplex
change. Now only one unified notification is printed.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
actor_admin, and actor_oper key is changed at multiple locations in
the code. This patch brings all those updates into one location in
an attempt to avoid possible inconsistent updates causing LACP state
machine to go in weird state.
The unified place is ad_update_actor_key() with simple state-machine
logic -
(a) If port is "duplex" then only it can participate in LACP
(b) Speed change reinitializes the LACP state-machine.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate 'else' clause by simply initializing variable
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
BPF updates
This set adds support for persistent maps/progs. Please see
individual patches for further details. A man-page update
to bpf(2) will be sent later on, also a iproute2 patch for
support in tc.
v1 -> v2:
- Reworked most of patch 4 and 5
- Rebased to latest net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds support for "persistent" eBPF maps/programs. The term
"persistent" is to be understood that maps/programs have a facility
that lets them survive process termination. This is desired by various
eBPF subsystem users.
Just to name one example: tc classifier/action. Whenever tc parses
the ELF object, extracts and loads maps/progs into the kernel, these
file descriptors will be out of reach after the tc instance exits.
So a subsequent tc invocation won't be able to access/relocate on this
resource, and therefore maps cannot easily be shared, f.e. between the
ingress and egress networking data path.
The current workaround is that Unix domain sockets (UDS) need to be
instrumented in order to pass the created eBPF map/program file
descriptors to a third party management daemon through UDS' socket
passing facility. This makes it a bit complicated to deploy shared
eBPF maps or programs (programs f.e. for tail calls) among various
processes.
We've been brainstorming on how we could tackle this issue and various
approches have been tried out so far, which can be read up further in
the below reference.
The architecture we eventually ended up with is a minimal file system
that can hold map/prog objects. The file system is a per mount namespace
singleton, and the default mount point is /sys/fs/bpf/. Any subsequent
mounts within a given namespace will point to the same instance. The
file system allows for creating a user-defined directory structure.
The objects for maps/progs are created/fetched through bpf(2) with
two new commands (BPF_OBJ_PIN/BPF_OBJ_GET). I.e. a bpf file descriptor
along with a pathname is being passed to bpf(2) that in turn creates
(we call it eBPF object pinning) the file system nodes. Only the pathname
is being passed to bpf(2) for getting a new BPF file descriptor to an
existing node. The user can use that to access maps and progs later on,
through bpf(2). Removal of file system nodes is being managed through
normal VFS functions such as unlink(2), etc. The file system code is
kept to a very minimum and can be further extended later on.
The next step I'm working on is to add dump eBPF map/prog commands
to bpf(2), so that a specification from a given file descriptor can
be retrieved. This can be used by things like CRIU but also applications
can inspect the meta data after calling BPF_OBJ_GET.
Big thanks also to Alexei and Hannes who significantly contributed
in the design discussion that eventually let us end up with this
architecture here.
Reference: https://lkml.org/lkml/2015/10/15/925
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have duplicated cleanup code in bpf_prog_put() and
bpf_prog_put_rcu() cleanup paths. Back then we decided that it was
not worth it to make it a common helper called by both, but with
the recent addition of resource charging, we could have avoided
the fix in commit ac00737f4e ("bpf: Need to call bpf_prog_uncharge_memlock
from bpf_prog_put") if we would have had only a single, common path.
We can simplify it further by assigning aux->prog only once during
allocation time.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bpf_map_get() function that we're going to use later on and
align/clean the remaining helpers a bit so that we have them a bit
more consistent:
- __bpf_map_get() and __bpf_prog_get() that both work on the fd
struct, check whether the descriptor is eBPF and return the
pointer to the map/prog stored in the private data.
Also, we can return f.file->private_data directly, the function
signature is enough of a documentation already.
- bpf_map_get() and bpf_prog_get() that both work on u32 user fd,
call their respective __bpf_map_get()/__bpf_prog_get() variants,
and take a reference.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're going to use anon_inode_getfd() invocations in more than just
the current places, make a helper function for both, so that we only need
to pass a map/prog pointer to the helper itself in order to get a fd. The
new helpers are called bpf_map_new_fd() and bpf_prog_new_fd().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following problems :
1) percpu_counter_init() can return an error, therefore
init_frag_mem_limit() must propagate this error so that
inet_frags_init_net() can do the same up to its callers.
2) If ip[46]_frags_ns_ctl_register() fail, we must unwind
properly and free the percpu_counter.
Without this fix, we leave freed object in percpu_counters
global list (if CONFIG_HOTPLUG_CPU) leading to crashes.
This bug was detected by KASAN and syzkaller tool
(http://github.com/google/syzkaller)
Fixes: 6d7b857d54 ("net: use lib/percpu_counter API for fragmentation mem accounting")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under low memory conditions, tcp_sk_init() and icmp_sk_init()
can both iterate on all possible cpus and call inet_ctl_sock_destroy(),
with eventual NULL pointer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exynos GEM objects contains an array of pointers to the pages, which the
allocated buffer consists of. Till now the code used some hacks (like
relying on DMA-mapping internal structures or using ARM-specific
dma_to_pfn helper) to build this array. This patch fixes this by adding
proper call to dma_get_sgtable_attrs() and using the acquired scatter-list
to construct needed array. This approach is more portable (work also for
ARM64) and finally fixes the layering violation that was present in this
code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Mixer driver is selected by CONFIG_DRM_EXYNOS_HDMI option. Since Exynos5433
HDMI does not require Mixer. There will be separate options to select Mixer
and HDMI. Adding new option to defconfig before Kconfig will allow to keep
bisectability.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Many Exynos DRM sub-options mentions Exynos DRM in their titles.
It is redundant and can be safely shortened. The patch additionally
makes some entries more descriptive.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos DRM driver have quite big number of components and options.
The patch re-arranges them into three logical groups:
- CRTCs,
- Encoders and Bridges,
- Sub-drivers.
It should make driver options more clear.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All options depends on DRM_EXYNOS so it can be moved to enclosing if clause.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Latest Exynos SoCs does not have Mixer IP, but they still have HDMI IP.
Their drivers should be configurable separately.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
HDMI driver called directly function from MIXER driver to invalidate modes
not supported by MIXER. The patch replaces the hack with proper .atomic_check
callback.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some CRTCs needs mode validation, this patch adds neccessary
callback to Exynos DRM framework. It is called from DRM core
via atomic_check helper for drm_crtc.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON-TV IP is responsible for generating video stream which is transferred
to HDMI IP. It is almost fully compatible with DECON IP.
The patch is based on initial work of Hyungwon Hwang.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Field .commit is already initialized few lines above.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Driver uses four different fields for internal flags. They can be merged
into one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver often sets only particular bits of configuration registers.
Using separate function to such action simplifies the code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All timing registers should contain values decreased by one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
PCLK clock is used by DECON IP. The patch also replaces magic number with
number of clocks in array definition.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This document is based on three recent lwn.net articles.
Some of the introductory material and linkage between articles
has been removed, and some time-based descriptions have been
revised.
Also all links to code have been removed as the code is very close by.
Contains corrections and improvements from Randy Dunlap <rdunlap@infradead.org>.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add documentation on how to use slabinfo-gnuplot.sh script.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch fix some spelling typos in Documentation/ABI/stable.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Quite a few new features for regmap this time, mostly expanding things
around the edges of the existing functionality to cover more devices
rather than thinsg with wide applicability:
- Support for offload of the update_bits() operation to hardware where
devices implement bit level access.
- Support for a few extra operations that need scratch buffers on
fast_io devices where we can't sleep.
- Expanded the feature set of regmap_irq to cope with some extra
register layouts.
- Cleanups to the debugfs code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWN6usAAoJECTWi3JdVIfQT7cH/1sNJlpt8s2pu/29LtBN0oMH
ZPPT8p46Xph7lbVMbMWZfgcobtISKMYo8dGDEeIYR1c1DZObErJSDxj5I/g5PxUv
FuJ1kVeJ0L0GJE78sB69LQQUAYXfmbtOnmivok/huNID+wpZbTE7uZjAby4tffuk
Mom2TLSnrm63j/zDnsi4VBAB9w1pQCIp+UiJ8LR8PCglcSHJ/eZLrh53F6BzXRU8
9QseD5YQCh4d3go6QZhVNX8iJEby9ehmtCnzN8zEfpXKpc2T1pCoHEH/BnKnxd16
i35A4RjW0GZfilS1815prjDhHJSbrQiqzyIh7Wua+zll7kCx6K/oLdjUfTIK9L0=
=A8Lm
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Quite a few new features for regmap this time, mostly expanding things
around the edges of the existing functionality to cover more devices
rather than thinsg with wide applicability:
- Support for offload of the update_bits() operation to hardware
where devices implement bit level access.
- Support for a few extra operations that need scratch buffers on
fast_io devices where we can't sleep.
- Expanded the feature set of regmap_irq to cope with some extra
register layouts.
- Cleanups to the debugfs code"
* tag 'regmap-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Allow installing custom reg_update_bits function
regmap: debugfs: simplify regmap_reg_ranges_read_file() slightly
regmap: debugfs: use memcpy instead of snprintf
regmap: debugfs: use snprintf return value in regmap_reg_ranges_read_file()
regmap: Add generic macro to define regmap_irq
regmap: debugfs: Remove scratch buffer for register length calculation
regmap: irq: add ack_invert flag for chips using cleared bits as ack
regmap: irq: add support for chips who have separate unmask registers
regmap: Allocate buffers with GFP_ATOMIC when fast_io == true
Calling ioctl(..., RTC_UIE_ON, ...) without CONFIG_RTC_INTF_DEV_UIE_EMUL
either ends in rtc_update_irq_enable if rtc->uie_unsupported is true
or in __rtc_set_alarm in the if (!rtc->ops->set_alarm) branch. In both
cases the return value is -EINVAL. So check for that one instead of
ENOTTY.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The header of the pcf2127 driver specifies GPL v2 only as license, so
use "GPL v2" as module license specifier instead of "GPL" as the latter
means "GNU Public License v2 or later".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The documentation on top of __DECLARE_TRACE() does not match its
implementation since the condition check has been added to the
RCU lockdep checks. Update the documentation to match its
implementation.
Link: http://lkml.kernel.org/r/1446504164-21563-1-git-send-email-mathieu.desnoyers@efficios.com
CC: Dave Hansen <dave@sr71.net>
Fixes: a05d59a567 "tracing: Add condition check to RCU lockdep checks"
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In addition to a variety of bugfixes, these patches are mostly geared at
enabling both swap and backchannel support to the NFS over RDMA client.
Signed-off-by: Anna Schumake <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ush5
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-4.4-2' of git://git.linux-nfs.org/projects/anna/nfs-rdma
NFS: NFSoRDMA Client Side Changes
In addition to a variety of bugfixes, these patches are mostly geared at
enabling both swap and backchannel support to the NFS over RDMA client.
Signed-off-by: Anna Schumake <Anna.Schumaker@Netapp.com>
Changes for vmwgfx for 4.4. If there is time, I'll follow up with a series
to move to threaded irqs.
* 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Replace iowrite/ioread with volatile memory accesses
drm/vmwgfx: Turn off support for multisample count != 0 v2
drm/vmwgfx: switch from ioremap_cache to memremap
* pci/aer:
PCI/AER: Clear error status registers during enumeration and restore
* pci/hotplug:
PCI: pciehp: Queue power work requests in dedicated function
* pci/misc:
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
x86/PCI: Make pci_subsys_init() static
PCI: Add builtin_pci_driver() to avoid registration boilerplate
PCI: Remove unnecessary "if" statement
* pci/msi:
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
PCI/MSI: Export all remapped MSIs to sysfs attributes
PCI: Disable MSI on SiS 761
* pci/resource:
sparc/PCI: Add mem64 resource parsing for root bus
PCI: Expand Enhanced Allocation BAR output
PCI: Make Enhanced Allocation bitmasks more obvious
PCI: Handle Enhanced Allocation capability for SR-IOV devices
PCI: Add support for Enhanced Allocation devices
PCI: Add Enhanced Allocation register entries
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
* pci/virtualization:
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
PCI: Wait 1 second between disabling VFs and clearing NumVFs
PCI: Reorder pcibios_sriov_disable()
PCI: Remove VFs in reverse order if virtfn_add() fails
PCI: Remove redundant validation of SR-IOV offset/stride registers
PCI: Set SR-IOV NumVFs to zero after enumeration
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
PCI: Don't try to restore VF BARs
Fix code comment about kmsg_dump register so it matches the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The first argument name in the kernel-doc argument list for
efi_pstore_scan_sysfs_enter() was slightly off. Fix it for the
kernel doc.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Layerscape PCIe has its own MSI implementation.
Register ls_pcie_msi_host_init() to avoid using DesignWare's MSI.
[bhelgaas: add comment]
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Both LS1043a and LS2080a are based on ARMv8 64-bit architecture and have
similar PCIe implementation. LUT is added to controller.
Add LS1043a and LS2080a support.
[bhelgaas: move unused field removal into separate patch, include DT update]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> (DT update)
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de> (DT update)
Removed unused node, dev, and bus fields from struct ls_pcie.
[bhelgaas: split into separate patch]
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update the ls_add_pcie_port() signature to keep it consistent with the
other DesignWare-based host drivers.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For the LS1021a PCIe controller, some status registers are located in SCFG,
unlike other Layerscape devices.
Move SCFG-related code to ls1021_pcie_host_init() and rename
ls_pcie_link_up() to ls1021_pcie_link_up() because LTSSM status is also in
SCFG.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Layerscape PCIe controller supports root complex (RC) and endpoint (EP)
modes, which can be set by RCW.
If not in RC mode, return -ENODEV without claiming the controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
