.recalc_rate callback for the fractional PLL doesn't take operating
mode into account when calculating PLL rate. This results in
the incorrect PLL rates when PLL is operating in integer mode.
Operating mode of fractional PLL is based on the value of the
fractional divider. Currently it assumes that the PLL will always
be configured in fractional mode which may not be
the case. This may result in the wrong output frequency.
Also vco was calculated based on the current operating mode which
makes no sense because .set_rate is setting operating mode. Instead,
vco should be calculated using PLL settings that are about to be set.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PLL enable callbacks are overriding PLL mode (int/frac) and
Noise reduction (on/off) settings set by the boot loader which
results in the incorrect clock rate.
PLL mode and noise reduction are defined by the DSMPD and DACPD bits
of the PLL control register. PLL .enable() callbacks enable PLL
by deasserting all power-down bits of the PLL control register,
including DSMPD and DACPD bits, which is not necessary since
these bits don't actually enable/disable PLL.
This commit fixes the problem by removing DSMPD and DACPD bits
from the "PLL enable" mask.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresitcker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit fixes 32bit integer overflows throughout the pll driver
(i.e. wherever the result of integer multiplication may exceed the
range of u32).
One of the functions affected by this problem is .recalc_rate. It
returns incorrect rate for some pll settings (not for all though)
which in turn results in the incorrect rate setup of pll's child
clocks.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
RFC 4443 added two new codes values for ICMPv6 type 1:
5 - Source address failed ingress/egress policy
6 - Reject route to destination
And RFC 7084 states in L-14 that IPv6 Router MUST send ICMPv6 Destination
Unreachable with code 5 for packets forwarded to it that use an address
from a prefix that has been invalidated.
Codes 5 and 6 are more informative subsets of code 1.
Signed-off-by: Andreas Herz <andi@geekosphere.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull block fixes from Jens Axboe:
"Two fixes in this pull request:
- The writeback regression fix from Tejun, which has been weeks in
the making. This fixes a case where we would sometimes not issue
writeback when we should have.
- An older fix for a memory corruption issue in mtip32xx. It was
deferred since we wanted a better fix for this (driver should not
have to handle that case), but given the timing, it's better to put
the simple fix in for 4.2 release"
* 'for-linus' of git://git.kernel.dk/linux-block:
mtip32x: fix regression introduced by blk-mq per-hctx flush
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
Alexei Starovoitov says:
====================
act_bpf: remove spinlock in fast path
v1 version had a race condition in cleanup path of bpf_prog.
I tried to fix it by adding new callback 'cleanup_rcu' to 'struct tcf_common'
and call it out of act_api cleanup path, but Daniel noticed
(thanks for the idea!) that most of the classifiers already do action cleanup
out of rcu callback.
So instead this set of patches converts tcindex and rsvp classifiers to call
tcf_exts_destroy() after rcu grace period and since action cleanup logic
in __tcf_hash_release() is only called when bind and refcnt goes to zero,
it's guaranteed that cleanup() callback is called from rcu callback.
More specifically:
patches 1 and 2 - simple fixes
patches 2 and 3 - convert tcf_exts_destroy in tcindex and rsvp to call_rcu
patch 5 - removes spin_lock from act_bpf
The cleanup of actions is now universally done after rcu grace period
and in the future we can drop (now unnecessary) call_rcu from tcf_hash_destroy()
patch 5 is using synchronize_rcu() in act_bpf replacement path, since it's
very rare and alternative of dynamically allocating 'struct tcf_bpf_cfg' just
to pass it to call_rcu looks even less appealing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to act_gact/act_mirred, act_bpf can be lockless in packet processing
with extra care taken to free bpf programs after rcu grace period.
Replacement of existing act_bpf (very rare) is done with synchronize_rcu()
and final destruction is done from tc_action_ops->cleanup() callback that is
called from tcf_exts_destroy()->tcf_action_destroy()->__tcf_hash_release() when
bind and refcnt reach zero which is only possible when classifier is destroyed.
Previous two patches fixed the last two classifiers (tcindex and rsvp) to
call tcf_exts_destroy() from rcu callback.
Similar to gact/mirred there is a race between prog->filter and
prog->tcf_action. Meaning that the program being replaced may use
previous default action if it happened to return TC_ACT_UNSPEC.
act_mirred race betwen tcf_action and tcfm_dev is similar.
In all cases the race is harmless.
Long term we may want to improve the situation by replacing the whole
tc_action->priv as single pointer instead of updating inner fields one by one.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust destroy path of cls_rsvp to call tcf_exts_destroy() after
rcu grace period.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust destroy path of cls_tcindex to call tcf_exts_destroy() after
rcu grace period.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix harmless typo and avoid unnecessary copy of empty 'prog' into
unused 'strcut tcf_bpf_cfg old'.
Fixes: f4eaed28c7 ("act_bpf: fix memory leaks when replacing bpf programs")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcf_hash_destroy() used once. Make it static.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers for devices connected via SPI to check if the
controller supports a given bits_per_word value during setup.
Currently any BPW value is accepted durings setup, and transfers
are rejected later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver crashes if the BIOS do not set up at least one
memory I/O resource. This failure can happen if the device is too
slow to respond during POST and is missed by the BIOS, but Linux
then detects the device later in the boot process.
Based on a patch from Timothy Pearson <tpearson@raptorengineeringinc.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The Kconfig option AVERAGE and its implementation has been removed by
commit f4e774f55f ("average: remove out-of-line implementation").
Remove the dead build rule in lib/Makefile.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Surround conditional locking statements with "#ifndef __CHECKER__" /
"#endif" to hide these for the sparse static source code analysis
tool.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The "return QLA_SUCCESS" statement just above the "fw_load_failed"
label cannot be reached, hence remove it. Additionally remove the
"else" keyword since the code block below the if-statement ends
with a return statement.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Avoid that smatch reports the following warning:
drivers/scsi/qla2xxx/qla_attr.c:1081: qla2x00_model_desc_show() warn: this array is probably non-NULL. 'vha->hw->model_desc'
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch removes 21 casts between an __iomem pointer type and
another data type but also introduces five new casts (see also
the casts with "__force"). Although this patch does not change
any functionality, IMHO the code with __force casts needs further
review.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Whether htonl() or __constant_htonl() is used, if the argument
is a constant the conversion happens at compile time. Hence leave
out the __constant_ prefix for this and other endianness
conversion functions. This improves source code readability.
[jejb: checkpatch fixes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Replace the QLA82XX_ADDR_IN_RANGE() and QLA8044_ADDR_IN_RANGE() macros
with the inline function addr_in_range(). This avoids that the compiler
reports the following warning when building with W=1: comparison of
unsigned expression >= 0 is always true.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Let the debug statement in qlafx00_tm_iocb_entry() report both rsp_info
and rsp_info_len instead of reporting rsp_info_len twice.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.
The new naming convention boils down to: s/Crucial_/FC/
Signed-off-by: Guillermo A. Amaral <g@maral.me>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Implement magic sysrequest handling for the VT220 terminal (also known as
the Integrated ASCII console on the HMC/SE).
To invoke a "magic sysrequest" function, press "Ctrl+o" followed by a
second character that designates the debugging function.
The handling of the sysrq is scheduled away from the SCLP IRQ context;
because large amounts of sysrq output might fill up the console buffers.
The console might deadlock because it cannot empty the buffers while still
in the receiving IRQ context. This behavior is the same as for the SCLP
console.
Reported-by: Horst Weber <hweber@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Extract the sysrq handling from the ctrlchar_handle() into a separate
function that can be directly used by other users.
Introduce a new sysrq_work structure to embed the work_struct and to
specify the magic sysrq function to be invoked.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The NUMA system call "__ARCH_WANT" defines are not used by the
Linux kernel, therefore remove them.
Fixes: 9df62adffeb0 ("s390/numa: add core infrastructure")
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a 3270 terminal is disconnected and later reconnected again,
it gets an unsolicited device end. This is currently ignored and
you have to hit the clear key to get the screen redrawn.
Add an automatic full redraw of the screen for this case.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch enables the PRCHK and reftag support when PRACT bit is set, and
block layer integrity is disabled.
Signed-off-by: Alok Pandey <pandey.alok@samsung.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use dev_printk() when possible to make messages more useful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use dev_printk() when possible to make messages more useful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Log the ALUA state change unit attention correctly with
the message log and emit an event to allow user-space
tools to react to it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
These are signed values the come from the user, we put a cap on the
upper bounds but not on the lower bounds.
We use "karg.dataSgeOffset" to calculate "sz". We verify "sz" and
proceed as if that means that "karg.dataSgeOffset" is correct but this
fails to consider that the "sz" calculations can have integer overflows.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
It should be useful to allow 'perf probe' probe at absolute offset of a
target. For example, when (u)probing at a instruction of a shared object
in a embedded system where debuginfo is not avaliable but we know the
offset of that instruction by manually digging.
This patch enables following perf probe command syntax:
# perf probe 0xffffffff811e6615
And
# perf probe /lib/x86_64-linux-gnu/libc-2.19.so 0xeb860
In the above example, we don't need a anchor symbol, so it is possible
to compute absolute addresses using other methods and then use 'perf
probe' to create the probing points.
v1 -> v2:
Drop the leading '+' in cmdline;
Allow uprobing at offset 0x0;
Improve 'perf probe -l' result when uprobe at area without debuginfo.
v2 -> v3:
Split bugfix to a separated patch.
Test result:
# perf probe 0xffffffff8119d175 %ax
# perf probe sys_write %ax
# perf probe /lib64/libc-2.18.so 0x0 %ax
# perf probe /lib64/libc-2.18.so 0x5 %ax
# perf probe /lib64/libc-2.18.so 0xd8e40 %ax
# perf probe /lib64/libc-2.18.so __write %ax
# perf probe /lib64/libc-2.18.so 0xd8e49 %ax
# cat /sys/kernel/debug/tracing/uprobe_events
p:probe_libc/abs_0 /lib64/libc-2.18.so:0x (null) arg1=%ax
p:probe_libc/abs_5 /lib64/libc-2.18.so:0x0000000000000005 arg1=%ax
p:probe_libc/abs_d8e40 /lib64/libc-2.18.so:0x00000000000d8e40 arg1=%ax
p:probe_libc/__write /lib64/libc-2.18.so:0x00000000000d8e40 arg1=%ax
p:probe_libc/abs_d8e49 /lib64/libc-2.18.so:0x00000000000d8e49 arg1=%ax
# cat /sys/kernel/debug/tracing/kprobe_events
p:probe/abs_ffffffff8119d175 0xffffffff8119d175 arg1=%ax
p:probe/sys_write _text+1692016 arg1=%ax
# perf probe -l
Failed to find debug information for address 5
probe:abs_ffffffff8119d175 (on sys_write+5 with arg1)
probe:sys_write (on sys_write with arg1)
probe_libc:__write (on @unix/syscall-template.S:81 in /lib64/libc-2.18.so with arg1)
probe_libc:abs_0 (on 0x0 in /lib64/libc-2.18.so with arg1)
probe_libc:abs_5 (on 0x5 in /lib64/libc-2.18.so with arg1)
probe_libc:abs_d8e40 (on @unix/syscall-template.S:81 in /lib64/libc-2.18.so with arg1)
probe_libc:abs_d8e49 (on __GI___libc_write+9 in /lib64/libc-2.18.so with arg1)
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1440586666-235233-7-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch fixes a bug that, when offset is provided but function is
lost, parse_perf_probe_point() will give a "" string as function name,
so the checking code at the end of parse_perf_probe_point() become
useless. For example:
# perf probe +0x1234
Failed to find symbol in kernel
Error: Failed to add events.
After this patch:
# perf probe +0x1234
Semantic error :Offset requires an entry function.
Error: Command Parse Error.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1440586666-235233-6-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When manually added uprobe point with zero address, 'perf probe -l'
reports error. For example:
# echo p:probe_libc/abs_0 /path/to/lib.bin:0x0 arg1=%ax > \
/sys/kernel/debug/tracing/uprobe_events
# perf probe -l
Error: Failed to show event list.
Probing at 0x0 is possible and useful when lib.bin is not a normal
shared object but is manually mapped. However, in this case kernel
report:
# cat /sys/kernel/debug/tracing/uprobe_events
p:probe_libc/abs_0 /path/to/lib.bin:0x (null) arg1=%ax
This patch supports the above kernel output.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1440586666-235233-5-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf probe -l' reports error if it is unable find symbol through
address. Here is an example.
# echo 'p:probe_libc/abs_5 /lib64/libc.so.6:0x5' >
/sys/kernel/debug/tracing/uprobe_events
# cat /sys/kernel/debug/tracing/uprobe_events
p:probe_libc/abs_5 /lib64/libc.so.6:0x0000000000000005
# perf probe -l
Error: Failed to show event list
Also, this situation triggers a logical inconsistency in
convert_to_perf_probe_point() that, it returns ENOMEM but actually it
never try strdup().
This patch removes !tp->module && !is_kprobe condition, so it always
uses address to build function name if symbol not found.
Test result:
# perf probe -l
probe_libc:abs_5 (on 0x5 in /lib64/libc.so.6)
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1440586666-235233-4-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It's sometimes useful to specify the object affiliation to multiple
config options like:
libperf-$(CONFIG_X86) += tsc.o
libperf-$(CONFIG_AUXTRACE) += tsc.o
while the object itself is linked only once. Adding the support for this
and ignoring duplicate objects in the object list.
Suggested-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20150826130103.GF22670@krava.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We don't carry an export.h wrapper anymore, remove it from the MANIFEST
file to avoid breaking the make perf-tar targets.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20150826080750.GD22670@krava.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf probe -l' panic if there is a manually inserted probing point with
absolute address. For example:
# echo 'p:probe/abs_ffffffff811e6615 0xffffffff811e6615' > /sys/kernel/debug/tracing/kprobe_events
# perf probe -l
Segmentation fault (core dumped)
This patch fix this problem by considering the situation that
"tp->symbol == NULL" in find_perf_probe_point_from_dwarf() and
find_perf_probe_point_from_map().
After this patch:
# perf probe -l
probe:abs_ffffffff811e6615 (on SyS_write+5@fs/read_write.c)
And when debug info is missing:
# rm -rf ~/.debug
# mv /lib/modules/4.2.0-rc1+/build/vmlinux /lib/modules/4.2.0-rc1+/build/vmlinux.bak
# perf probe -l
probe:abs_ffffffff811e6615 (on sys_write+5)
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1440509256-193590-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if
kernel doesn't support MSI"), the setup of dev->msi_cap/msix_cap and the
disable of MSI/MSI-X interrupts isn't being done at PCI probe time, as
the logic responsible for this was moved in the aforementioned commit
from pci_device_add() to pci_setup_device(). The latter function is not
reachable on PowerPC pseries platform during Open Firmware PCI probing
time.
This exhibits as drivers not being able to enable MSI, eg:
bnx2x 0000:01:00.0: no msix capability found
This patch calls pci_msi_setup_pci_dev() explicitly to disable MSI/MSI-X
during PCI probe time on pSeries platform.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Flesh out change log and clarify comment]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.
wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'long unsigned int' [-Wformat=]
left_len, sizeof(*phyerr));
^
Fixes: 991adf71a6 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).
The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:
ath10k_pci 0000:02:00.0: firmware register dump:
ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
...
Note the value 0x000A012D.
Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.
In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.
This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
