This controller not only supports higher resolutions than the K1900
but concurrent updates as well. This results in a generally higher
display speed.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This controller only supports smaller resolutions and only serial
updates, i.e. it has to wait for an update to finish before
starting another one.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The AUO-K190X controllers share a very similar set of commands and
can therefore also share most of the driver code.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
With this optional callback the driver is notified when the first page
is entered into the pagelist and a new deferred_io call is scheduled.
A possible use-case for this is runtime-pm. In the first_io call
pm_runtime_get()
could be called, which starts an asynchronous runtime_resume of the
device. In the deferred_io callback a call to
pm_runtime_barrier()
makes the sure, the device is resumed by then and a
pm_runtime_put()
may put the device back to sleep.
Also, some SoCs may use the runtime-pm system to determine if they
are able to enter deeper idle states. Therefore it is necessary to
keep the use-count from the first written page until the conclusion
of the screen update, to prevent the system from going to sleep before
completing the pending update.
Two users of defio were using kmalloc to allocate the structure.
These allocations are changed to kzalloc, to prevent uninitialised
.first_io members in those drivers.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add support for LCD panel on MIPS SEAD-3 development platform.
Signed-off-by: Douglas Leung <douglas@mips.com>
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This file has an implicit dependency on GPIO stuff, showing
up as the following build failure:
drivers/video/bfin-lq035q1-fb.c:369:6: error: 'GPIOF_OUT_INIT_LOW' undeclared
Other more global bfin build issues prevent an automated bisect, but
it really doesn't matter - simply add in the appropriate header.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Bernie Thompson <bernie@plugable.com>
CC: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The exynos_mipi_dsi_set_main_disp_[hv]porch() functions take front and
back porch arguments in that order. This maps to the fb_videomode
right/lower_margin and left/upper_margin respectively. Fix the caller
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
EFI doesn't typically make use of the legacy VGA ROM, but it may still be
configured to pass that through to a given video device. This may lead to
an inaccurate choice of default video device. Add support to efifb to pick
out the correct active video device.
v2: fix if->ifdef
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: hpa@zytor.com
Cc: matt.fleming@intel.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add displays to panel-generic-dpi.c
Prime View PD050VL1 (640 x 480)
Prime View PD104SLF (800 x 600)
Prime View PM070WL4 (800 x 480)
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the DISPC manager timings related function by:
- Create a common function to set size for LCD and TV.
- Create a common function to check timings for LCD and TV.
- Add dss params to get the range of manager size.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, a LCD manager's timings is set by dispc_mgr_set_lcd_timings() and TV
manager's timings is set by dispc_set_digit_size(). Use a common function called
dispc_mgr_set_timings() which sets timings for both type of managers.
We finally want the interface drivers to use an overlay manager function to
configure it's timings, having a common DISPC function would make things
cleaner.
For LCD managers, dispc_mgr_set_timings() sets LCD size and blanking values, for
TV manager, it sets only the TV size since blanking values don't exist for TV.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The RFBI driver uses dispc_mgr_set_lcd_size() to set the width and height of
the LCD manager. Replace this to use dispc_mgr_set_lcd_timings(), pass dummy
blanking parameters like done in the DSI driver.
This prevents the need to export dispc_mgr_set_lcd_size(), and use a common
function to set lcd timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
code depending on FB_OMAP_BOOTLOADER_INIT has been removed long before
(e.g. Tomi Valkeinen, 03 Mar 2011: OMAP: DSS2: Remove FB_OMAP_BOOTLOADER_INIT
support), but the option still exists Kconfig and has no use
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The EDT ET0500G0DH6 is a 5 inch display. It is
tested on an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for the Mitsubishi display
AA084SB01. This is a 7 inch LVDS display. It is tested with
an OMAP3 board.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On pandora we use .set_timings to alter refresh rate,
so add .check_timings/.set_timings functions.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the size of memory region that is being set up is the same as before,
we don't have to do memory and layer busy checks.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since any power on stabilisation delay for the supply itself should be
taken care of transparently by the regulator API when the regulator is
enabled the additional delay that the TPO-TD03MTEA1 driver adds after
that returned should be due to the requirements of the device itself
rather than the supply (the delay is also suspicously long for one for
a regulator to ramp). Correct the comment to avoid misleading people
taking this code as a reference.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It is possible for regulator_enable() to fail and if it does fail that's
generally a bad sign for anything we try to do with the hardware afterwards
so check for and immediately return an error if regulator_enable() fails.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TAAL driver contains some regulator support which is currently unused
(the code is there but the one panel supported by the driver doesn't have
any regulators provided). This code mostly looks like an open coded
version of the regulator core bulk API.
The only additional feature is that a voltage range can be set once when
the device is opened, though this is never varied at runtime. The general
expectation is that if the device is not actively managing the voltage of
the device (eg, doing DVFS) then any configuration will be done using the
constraints rather than by drivers, saving them code and ensuring that
they work well with systems where the voltage is not configurable.
If systems are added needing regulator support this can be added back in,
though it should be based on core features rather than open coding things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For some OMAP versions the TRM says that the pixel clock from DISPC can
be used as an input clock for DSI PLL, instead of the default, which is
sysclk. For some OMAP versions the bits affecting this are marked as
reserved. This feature has never been tested, so it's unknown if the HW
even works, and has never been used.
To clean things up, this patch removes the functionality. This should
not affect any board.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most of the DSS clocks have restrictions on their frequency based on the
OPP in use. For example, maximum frequency for a clock may be 180MHz in
OPP100, but 90MHz in OPP50. This means that when a high enough pixel
clock or function clock is required, we need to use OPP100.
However, there's currently no way in the PM framework to make that kind
of request. The closest we get is to ask for very high bus throughput
from the PM framework, which should effectively force OPP100.
This patch is a simple version for handling the problem. Instead of
asking for OPP100 only when needed, this patch asks for OPP100 whenever
DSS is active. This obviously is not an optimal solution for cases with
small displays where OPP50 would work just fine. However, a proper
solution is a complex one, and this patch is a short term solution for
the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
If there's some traffic on the LCD controller pads, the BootROM has trouble with
sampling the bootmode from these pads. The BootROM usually ends in a loop.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Chen Peter-B29397 <B29397@freescale.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Li Frank-B20596 <B20596@freescale.com>
Cc: Lin Tony-B19295 <B19295@freescale.com>
Cc: Linux FBDEV <linux-fbdev@vger.kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Subodh Nijsure <snijsure@grid-net.com>
Cc: Tony Lin <tony.lin@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The test tested not the most recently allocated value but a previously
allocated one.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
There were two problems in this code: failure of the setup function should
free locally allocated resources like other nearby failures, and the test
if (&info->cmap) can never be false. To generally clean things up, this
patch reorders the error handling code at the failed label and adds labels
so that the conditionals are not necessary.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The change
commit 461cbe77d0
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:13 2010 -0700
video: msm: Fix section mismatch in mddi.c.
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds analog and pll control setting. This control setting
is used for DP TX PHY block to set the values as below. It is beneficial
to improve analog characteristics.
- TX terminal registor is 50 Ohm.
- Reference clock of PHY is 24 MHz.
- Power source for TX digital logic is 1.0625 V.
- Power source for internal clock driver is 1.0625 V.
- PLL VCO range setting is 600 uA.
- Power down ring osc is turned off.
- AUX terminal resistor is 50 Ohm.
- AUX channel current is 8 mA and multiplied by 2.
- TX channel output amplitude is 400 mV.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The char pointer for adjust_request variable is replaced with char array
to fix possible null pointer dereference when clock recovery is failed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
DP PLL Lock status should be checked in order to prevent unlocked PLL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds runtime_get/put to suspend/resume, which should be
necessary to prevent the problem to access the fimd register
without block power on.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* A handful of warning and build fixes for Qualcomm MSM
* Build/warning and bug fixes for Samsung Exynos
* A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
* A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=OWRk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
- A handful of warning and build fixes for Qualcomm MSM
- Build/warning and bug fixes for Samsung Exynos
- A fix from Rob Herring that removes misplaced interrupt-parent
properties from a few device trees
- A fix to OMAP dealing with cpufreq build errors, removing some of the
offending code since it was redundant anyway
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
ARM: dts: remove blank interrupt-parent properties
ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
ARM: EXYNOS: Remove broken config values for touchscren for NURI board
ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
ARM: EXYNOS: fix regulator name for NURI board
ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
ARM: msm: Fix section mismatches in proc_comm.c
video: msm: Fix section mismatches in mddi.c
arm: msm: trout: fix compile failure
arm: msm: halibut: remove unneeded fixup
ARM: EXYNOS: Add PDMA and MDMA physical base address defines
ARM: S5PV210: Fix compiler warning in dma.c file
ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
ARM: EXYNOS: Add missing definition for IRQ_I2S0
ARM: S5PV210: fix unused LDO supply field from wm8994_pdata
The change
commit 461cbe77d0
Author: Gregory Bean <gbean@codeaurora.org>
Date: Wed Jul 28 10:22:13 2010 -0700
video: msm: Fix section mismatch in mddi.c.
fixes a section mismatch between the board file and the driver's probe
function, however, it misses the additional mismatches between the
probe function and some routines it calls. Fix these up as well.
Signed-off-by: David Brown <davidb@codeaurora.org>
If wait_event_interruptible_timeout returns a positive value, it means
the condition evaluated is true. Which means priv->shared->hw_running is false.
And then we will exit the loop.
This patch simplifies the logic to exit the while loop.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The decision to enable or disable the data output to the lcd panel from
the controller need not be based on the value of 'default_win' element
in the platform data. Instead, the data output to the panel is enabled
if any of the windows are active, else data output is disabled.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The video interface timing is independent of the window setup data.
The resolution of the window can be smaller than that of the lcd
panel to which the video data is output.
So move the video timing data from the per-window setup data to the
platform specific section in the platform data. This also removes
the restriction that atleast one window should have the same
resolution as that of the panel attached.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
kyrofb is completely broken on x86_64 because the registers are defined as
unsigned long. Change them to u32 to make the driver work.
Tested with Hercules 3D Prophet 4000XT.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
A bunch of fixes for regressions (and a few other problems) in 3.4-rc1:
* Fix for regression of mach/io.h cleanup on platforms with PCI or PCMCIA
(adding back the include file on those for now)
* AT91 fixes for usb and spi
* smsc911x ethernet fixes for i.MX
* smsc911x fixes for OMAP
* gpio fixes for Tegra
* A handful of build error and warning fixes for various platforms
* cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series, aren't
technically regressions for 3.4, but they're valid fixes and we're still
relatively early in the rc cycle so it seems appropriate to include them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RVTD
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
DA9052/53 PMIC has capability to supply power for upto 3 banks of 6
white serial LEDS. It can also control intensity of independent banks
and to drive these banks boost converter will provide up to 24V and
forward current of max 50mA.
This patch allows to control intensity of the individual WLEDs bank
through DA9052/53 PMIC.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 086ada54ab
"FB: sa1100: remove global sa1100fb_.*_power function pointers"
got rid of all instances but one in locomolcd.c -- which was
conditional on CONFIG_SA1100_COLLIE. The associated .power
field which replaces the global is populated in mach-sa1100/collie.c
so move the assignment there, but make it conditional on the
locomolcd support, so use CONFIG_BACKLIGHT_LOCOMO in that file.
Cc: arm@kernel.org
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
