The netbuf pop can return NULL. Make sure to check
for that. It shouldn't happen but better safe than
sorry.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's little point in dropping, e.g. frames with
FCS error early in ath10k.
This simplifies amsdu_allowed() and gets rid of
htt_rx_mpdu_status usage finally.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Treat non-chained and chained popping the same
way. Also this makes netbuf pop fully symmetrical
to (re)filling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tracing function was called before buffers were
unmapped from DMA.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the globally defined ieee80211 values instead
of re-defining them in the driver again.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx descriptor variable was no longer used in
the rx handler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HTT_RX_IND_MPDU_STATUS_MGMT_CTRL was pretty greedy
and because of that ath10k ended up dropping
Control Frames as well as Null Func frames.
Reported-by: Okhwan Lee <ohlee@mwnl.snu.ac.kr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not always convenient to have to know the device-id,
so allow deleting by name as well.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[use wiphy_name() instead of dev_name()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This gives a view into packet activity at the virtual radio
level.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As of commit e4dc601bf9 ("m68k: Disable/restore interrupts in
hwreg_present()/hwreg_write()"), this is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit e4dc601bf9 ("m68k: Disable/restore interrupts in
hwreg_present()/hwreg_write()"), this is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both image_data and typhoon_fw->data are const u8*, so the cast to u8*
is unnecessary and confusing.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e version to 1.0.21.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the three variables out of the loop, so it only declares once.
Change-ID: I436913777c7da3c16dc0031b59e3ffa61de74718
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add driver support for 10GBaseT device.
Change-ID: I4be6ed847ac0bddd220b9878a95c523b32038174
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to handle link events when updating the PF switch. This
allows link information to be properly provided to VFs in all cases.
Change-ID: If314c95f3d39259ef4c40a4a3b823381e28fb24f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the setting of flow control because this should be done at a pf level not
a vsi level. Also add a sleep and restart an to fix a bug where Rx would stop
after some stress.
Change-ID: I9a93d8c2ff27c39339eb00bc4ec1225e43900be0
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the Documentation/timers/timers-howto.txt it is preferred to use
usleep_range() instead of udelay() if the delay value is > 10us in
non-atomic contexts.
So, replacing all the instances of udelay() with 10 or greater than 10
micro seconds delay in the driver and using usleep_range() instead.
Change-ID: Iaa2ab499a4c26f6005e5d86cc421407ef9de16c7
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is one small step in making the indentation more consistent. If
we truly want to align values, then use tabs rather than spaces.
Change-ID: I12368bc77a52f296d1843fdcb67201a7d7cd4749
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
The driver can do a simpler job of managing link state by simply
using the admin queue receive event for link events as a doorbell
that tells the driver to update link state.
Additionally, add a workaround will help make sure the link state in the
hardware is consistent with the link state the driver is reporting
by refreshing the link state every service task interval.
Change-ID: Ib95b5b7b8cc016e97d8009f6363c9f9eed301444
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tell the firmware what kind of link related events the driver is
interested in. In this case, just link up/down and qualified module
events are the ones the driver really cares about.
Change-ID: If132c812c340c8e1927c2caf6d55185296b66201
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.
Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:
iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]
Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.
This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581
But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:
https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809
Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54c5 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.
Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.
We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Drivers that do not use the get_btc_status() callback may not define a
dummy routine. The caller needs to check before making the call.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Cc: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Thadeu Cascardo <cascardo@cascardo.eti.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases the limit may be the same as reg->power_limit, but the
actual value that the hardware uses is not up to date. In that case, a
wrong value for current tx power is tracked internally.
Fix this by unconditionally updating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a previous patch the call to ieee80211_register_hw was moved from the
load firmware callback to the rtl_pci_probe only.
rt8192cu also uses this callback. Currently it doesnt create a wlan%d device.
Fill in the call to ieee80211_register_hw in rtl_usb_probe.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize function pointer with a function indicating bt coexist is not there.
Prevents Ooops.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many AP devices do not have the proper regulatory domain programmed in
EEPROM. Instead they expect the software to set the appropriate region.
For these devices, the country code defaults to US, and the driver uses
the US CTL tables as well.
On devices bought in Europe this can lead to tx power being set too high
on the band edges, even if the cfg80211 regdomain is set correctly.
Fix this issue by taking into account the DFS region, but only when the
EEPROM regdomain is set to default.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reported a possible array overrun. The affected code
checks for overruns, but fails to take the steps necessary to fix them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.
Bug: https://dev.openwrt.org/ticket/18164
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use "%s" in the workqueue allocation to make sure the rtl_hal_cfg name
can never accidentally leak information via a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And changed from using strncat to strlcat to simplify code.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver logs a message when the default branch of switch statements are
taken. Such information is useful when debugging, but these log items should
not be seen for standard usage.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling init to reinit ce pipe state would also
re-set all static structure links and setting
(which don't change over driver lifecycle).
Make it so alloc links structures and initializes
static data and init part to setup state
variables and clear stuff.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was the final missing bit to making sure the
device doesn't assert interrupts to host.
This should fix possible race when target crashes
during driver teardown.
This also removes an early warm reset workaround
during pci probing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If MSI isn't configured device ROM program expects
legacy interrupts to be enabled before it can
fully boot. Don't forget to disable legacy
interrupts after that.
While at it re-use the legacy irq enabling helper
instead of calling ath10k_pci_write32().
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
total_data_buflen is used by netvsc_send() to decide if a packet can be put
into send buffer. It should also include the size of RNDIS message before the
Ethernet frame. Otherwise, a messge with total size bigger than send_section_size
may be copied into the send buffer, and cause data corruption.
[Request to include this patch to the Stable branches]
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the amd-xgbe driver increments the packets processed counter
each time a descriptor is processed. Since a packet can be represented
by more than one descriptor incrementing the counter in this way is not
appropriate. Also, since multiple descriptors cause the budget check
to be short circuited, sometimes the returned value from the poll
function would be larger than the budget value resulting in a WARN_ONCE
being triggered.
Update the polling logic to properly account for the number of packets
processed and exit when the budget value is reached.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support. Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 278d240478 (net: fec: ptp: Enable PPS output based on ptp clock)
fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls
into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to
dereference the NULL pointer.
Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called,
and fep->ptp_clock is NULL, which reliably causes a kernel panic.
This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After interface restart (eg: after link disconnection/reconnection), the bridge
function doesn't work anymore. This is due to the promiscuous mode being cleared
by the restart.
The mac-fcc already includes code to set the promiscuous mode back during the restart.
This patch adds the same handling to mac-fec and mac-scc.
Tested with bridge function on MPC885 with FEC.
Reported-by: Germain Montoies <germain.montoies@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_count and insert_count can wrap around, making > check invalid.
Fixes: 70b33fb0dd ("sfc: add support for
skb->xmit_more").
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
