Reconfigure RCR register in rtl_op_configure_filter() in order to apply RX
filter configuration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.
This is needed on systems where the external bus controller module of
the SoC is contained in a PM domain and/or has a gateable functional
clock. In such cases, before accessing any device connected to the
external bus, the PM domain must be powered up, and/or the functional
clock must be enabled, which is typically handled through runtime PM by
the bus controller driver.
An example of this is the kzm9g development board, where an smsc9220
Ethernet controller is connected to the Bus State Controller (BSC) of a
Renesas sh73a0 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
If xenvif_alloc() or xenbus_scanf() fail in backend_create_xenvif(),
xenbus is left in offline mode but netback_probe() reports success.
The patch implements propagation of error code for backend_create_xenvif().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Ben Hutchings drivers that allow using VLAN have to
provide enough headroom for the VLAN tags.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX fec support three rx ring1, the current driver lost to init
ring1 and ring2 maximum receive buffer size, that cause receving
frame date length error. The driver reports "rcv is not +last" error
log in user case.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a static checker warning:
drivers/net/wireless/brcm80211/brcmfmac/cfg80211.c:2965
brcmf_cfg80211_set_pmksa()
warn: can 'pmkid_len' be negative?
The answer to the question above is likely no so changing its
type to unsigned is sufficient.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rtbg
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-john-2014-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Emmanuel Grumbach <egrumbach@gmail.com> says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c17aa52c5b.
It was wrong, IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ
already implies that 160 MHz is supported, as it isn't a bitmap
but rather a value in a 2-bit field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are not many of these messages producted by the
firmware, but they are generally fairly useful, so make it easy to print them
with a separate debug level.
kvalo: fix commit log, rename debug level
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are better ways to get the kernel information, use the
utsname and omit the version code entirely since it's duplicate.
The version magic is rather useless anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
- Use config symbol defined in the driver instead of arch specific one for
conditional compilation.
- Rename the ATHEROS_AR231X config symbol to ATH25.
- Fix include (ar231x_platform.h -> ath25_platform.h).
- Some of AR231x SoCs (e.g. AR2315) have PCI bus support, so remove !PCI
dependency, which block AHB support build.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8248/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 093ec3c533.
AHB bus code has been removed, since we did not have support Atheros
AR231x SoC, required for building the AHB version of ath5k. Now that
support WiSoC chips added we can restore functionality back.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: linux-wireless@vger.kernel.org
Cc: ath5k-devel@lists.ath5k.org
Cc: Linux MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/8247/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a new SDIO card id intended for the new 4165 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver knows whether an rx frame was beamformed and marks
it in the radiotap VHT flags. However it should also declare
that it knows to extract this info otherwise this gets discarded
by sniffers like Wireshark.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add suspend/resume trans ops that will be called from
mac80211's suspend/resume ops.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the device wakes up due to netdetect, we need to query different
things from the firmware than when it wakes up with a normal WoWLAN.
To make this easier, separate the netdetect wake up handling from the
rest. For now, we don't send netdetect as a wake up reason, treating
it as a non-wireless wake up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the iwl_mvm_query_wakeup_reasons() function to split the part
that gets the firmware status from the part that sets up the WoWLAN
status. This will allow netdetect to reuse the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to send a WOWLAN_CONFIGURATION command also for netdetect and
configure the rfkill release trigger if needed. To do so, refactor
the code that configures wowlan and netdetect when suspending and send
the WOWLAN_CONFIGURATION command also for net_detect.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add the net detect WoWLAN flag to indicate support and use the
nd_config from the WoWLAN configuration to start net detect, if it is
set. The WoWLAN configuration takes precedence over the debugfs
configuration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When another vif is also running during a channel switch, we need to
use a session protection when we move to the new channel, so that we
don't miss the beacons. Without this, sometimes the other vif
repeatedly gets time exactly when we should be hearing the beacons,
preventing channel switch from completing. Adding a session
protection that lasts from the moment the channel changes until 2
TBTTs later, ensures that we will hear the beacons on the destination
channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
If setting the CSA time event fails, we must clear the TE data,
otherwise we'll try to remove it when, for instance, a disconnection
occurs, causing a SYSASSERT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
After a channel switch, transmission on the new channel is only
started once we see a beacon on it. Thus, beacon filtering needs to
be disabled during channel switch so that mac80211 receives this
beacon and finishes the process.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We need to call ieee80211_chswitch_done() ourselves just when the
absence TE started, so we perform the actual context switch early
enough. To do so, add a dummy channel_switch op, which will cause
mac80211 to skip the countdown timer and allow us to call
ieee80211_chswitch_done() to complete the operation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Now that mac80211 waits for the first beacon on the new channel before
calling post_channel_switch, the reconfiguration of the firmware
should be done in the post_channel_switch operation instead of when
assigning the vif to the new context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Instead of using a hardcoded number of TUs before beacon 0 as the time
to start the absence and actual channel switch, calculate it in
relation to the beacon interval. We use 10 TUs + beacon interval
before beacon 0 to target a bit before beacon 1. This gives us enough
time to switch to the new channel before the AP/GO switches.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add an absent time event when pre_channel_switch is called and use the
time event started indication to set the disable_tx bit instead of
doing it in unassign_vif(). This is done so that the firmware queues
are stopped before the actual switch takes place to avoid losing
packets while the AP/GO is performing its actual switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Now that all CSA flows are using the switch_vif_chanctx op, we can
rely on the switching_chanctx boolean that is passed to the
__iwl_mvm_assign_vif_chanctx() and __iwl_mvm_unassign_vif_chanctx()
functions to decide whether the context switch flows need to be
executed. In this way we make the chanctx switch flow more generic,
without having to rely on the csa_active flag being set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Disable PS when pre_channel_switch is called and add the
post_channel_switch operation to re-enable PS when the channel switch
is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The spec requires to decrement the CSA counters based on TBTT,
regardless if the beacon was actually transmitted. Previously, the fw
would send beacon notifications only for successfully transmitted
beacons. This behavior resulted in inaccurate CSA countdown. In order
to address this issue, the fw was changed to send beacon
notifications also for not transmitted beacons. Such notifications
have TX_STATUS_INTERNAL_ABORT (0x92).
Don't start the CSA countdown before first successfully transmitted
beacon, in order to guarantee that the CSA is announced for a
required period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We have code to recover and go back to the original channel context if
something fails in the middle of switch_vif_chanctx, but we return the
error code of the recover calls instead of the original code, so if
the recovery succeeds, we will return 0 (success). Fix this by not
assigning the return value of the recovery calls to ret.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add support to reassign vif in switch_vif_chanctx. This is similar to
the existing CHANCTX_SWMODE_SWAP_CONTEXTS mode, but doesn't delete the
old context nor creates a new one, doing to switch between two
existing contexts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Currently we only support the CHANCTX_SWMODE_SWAP_CONTEXTS mode, but
we need to support other modes as well. Spin a new function off in
order to make it easier to support other modes.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We only need the csa_vif in AP/GO modes, and assigning for other
interfaces may cause problems, because csa_vif is never cleared. To
prevent this, only assign the value if the iftype is
NL80211_IFTYPE_AP. Use a switch to do this, even though, for now,
only the AP interface type is handled, because soon other interface
types will be added as well.
Additionally, convert the WARN() in the error case when a
channel-switch is already running to WARN_ONCE().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
A new callback has been added to prepare the device for a channel
switch. Use the new callback instead of the old channel_switch_beacon
operation.
This makes it possible to remove the channel_switch_beacon operation
from mac80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Maintain a TDLS channel-switch state and update it according to
notifications from FW and timeouts. Explicitly check all state
transitions are valid.
When switching is initiated by mac80211, use a delayed work to
periodically reschedule it from iwlwifi.
Give the FW mac80211 generated TDLS channel-switch request/response
templates. It will change appropriate values (switch timings) and Tx
them at appropriate times.
Enable the channel switch wiphy capability bit when the FW supports it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Block TID 4 (VI) on a vif when using TDLS. This TID will be used by FW
for TDLS channel-switch requests and PTI requests.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When adding a TDLS station, allocate 4 new queues for it. Configure them
to FW and enable them. On station removal, drain the queues if needed
and disable them when empty.
Make sure to flush all packets in the private queues of TDLS stations in
the mac80211 flush() callback.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS peers are present the FW will send packets on a dedicated
TID vs. the peer when performing TDLS channel-switches. The driver
configures the TID on connection to the peer and the FW is responsible
for maintaining the state of QoS seqno and PN/IV for encryption.
If the FW asserts, the driver cannot correctly reconfigure the starting
seqno/PN to the reloaded FW, thus forcing us to reconnect the peer.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TDLS stations will have private queues, so consider them as well when
allocating a new one. Consolidate the HW-queue iterating code into
a single exported function, to be used by the TDLS code in the future.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send a dedicated TDLS_CONFIG command when a TDLS peer joins/leaves. The
fields for the command are mostly place-holders, as most of the FW
functionality is not implemented. In the future the dedicated FW TID
will be used for channel-switching and buffer-sta functionality.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
