GTIER and DEIER doesn't have same interface on HSW so this "or" operation
makes the information provided useless.
v2: since we have gtier variable already let's split for everybody
and avoid the strange | op.
Also avoid overriding the value that was set for vlv. In this case I
believe that we should reorganize the whole function, but I'll respect
the comment that ask to not touch the order and let this organization
work to be done later.
v3: moving VLV check to the right place.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Users often can't do anything about this since their vendors stopped
providing BIOS updates. Also we seem to be able to hack around it
with increased latency values, and thus far the only reports have
been for screens with really high resolutions. So tune it down to a
level where only developers can see it.
Also drop some of the end-user fluff.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Power users spot this and then get adventurous and try to adjust
module driver options. Nothing good ever came out of that, so
hide it better.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.
Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Acked-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix signal_offset when recording semaphore state on BDW.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.
v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.
v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gcc warns that addr might be used uninitialized. It may not, but I see
why gcc gets confused.
Additionally, hiding code with side-effects inside WARN_ON() argument
seems uncool, so I moved it outside.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[danvet: Add obligatory /* shuts up gcc */ comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the new devm_gpiod_get_optional() to simplify the probe code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm_vblank_cleanup() would operate on non-existent dev->vblank
data structure, as failure to allocate that data structure is
what triggers the error path in the first place.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During vblank disable the code tries to guess based on the
timestamps whether we just missed one vblank or not. And if so
it increments the counter. However it forgets to store the new
timestamp to the approriate slot in our timestamp ring buffer.
So anyone querying the timestamp for the resulting sequence
number would get a stale timestamp. Fix it up by storing the
new timestamp.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that drm_update_vblank_count() can be called even when we're not
about to enable the vblank interrupts we shouldn't print debug messages
stating otherwise.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
update_scanline_offset() in intel_sanitize_crtc() was supposed to
be called only for active crtcs. But due to some underrun patches it
now gets updated for all crtcs on gmch platforms.
Move the update_scanline_offset() to the very beginning of
intel_sanitize_crtc() where we update the vblank state. This seems like
a better place anyway since the scanline offset ought to be up to date
before we might need to consult it. So before any vblanky stuff happens.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the user is interested in getting accurate vblank sequence
numbers all the time they may disable the vblank disable timer
entirely. In that case it seems appropriate to kick start the
vblank interrupts already from drm_vblank_on().
v2: Adapt to the drm_vblank_offdelay ==0 vs <0 changes
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the vblank races are plugged, we can opt out of using
the vblank disable timer and just let vblank interrupts get
disabled immediately when the last reference is dropped.
Gen2 is the exception since it has no hardware frame counter.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a flag to drm_device which will cause the vblank code to bypass the
disable timer and always disable the vblank interrupt immediately when
the last reference is dropped.
v2: Add some notes about the flag to the kernel doc
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make drm_vblank_put() disable the vblank interrupt immediately when the
refcount drops to zero and drm_vblank_offdelay<0.
v2: Preserve the current drm_vblank_offdelay==0 'never disable' behaviur
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently it's possible that the following will happen:
1. drm_wait_vblank() calls drm_vblank_get()
2. drm_vblank_off() gets called
3. drm_wait_vblank() calls drm_queue_vblank_event() which
adds the event to the queue event though vblank interrupts
are currently disabled (and may not be re-enabled ever again).
To fix the problem, add another vblank->enabled check into
drm_queue_vblank_event().
drm_vblank_off() holds event_lock around the vblank disable,
so no further locking needs to be added to drm_queue_vblank_event().
vblank disable from another source is not possible since
drm_wait_vblank() already holds a vblank reference.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently both drm_irq.c and several drivers call drm_vblank_put()
while holding event_lock. Now that drm_vblank_put() can disable the
vblank interrupt directly it may need to grab vbl_lock and
vblank_time_lock. That causes deadlocks since we take the locks
in the opposite order in two places in drm_irq.c. So let's make
sure the locking order is always event_lock->vbl_lock->vblank_time_lock.
In drm_vblank_off() pull up event_lock from underneath vbl_lock. Hold
the event_lock across the whole operation to make sure we only send
out the events that were on the queue when we disabled the interrupt,
and not ones that got added just after (assuming drm_vblank_on() already
managed to get called somewhere between).
To sort the other deadlock pull the event_lock out from
drm_handle_vblank_events() into drm_handle_vblank() to be taken outside
vblank_time_lock. Add the appropriate assert_spin_locked() to
drm_handle_vblank_events().
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When drm_vblank_on() is called the hardware vblank counter may have
been reset, so we can't trust that the old values sampled prior to
drm_vblank_off() have anything to do with the new values.
So update the .last count in drm_vblank_on() to make the first
drm_vblank_enable() consider that as the reference point. This
will correct the user space visible counter to account for the
time between drm_vblank_on() and the first drm_vblank_enable()
calls.
For extra safety subtract one from the .last count in drm_vblank_on()
to make sure that user space will never see the same counter value
before and after modeset.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the vblank irq has already been disabled (via the disable timer) when
we call drm_vblank_off() sample the counter and timestamp one last time.
This will make the sure that the user space visible counter will account
for time between vblank irq disable and drm_vblank_off().
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move drm_update_vblank_count() to avoid forward a declaration.
No functional change.
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clearing the timestamps causes us to send zeroed timestamps to userspace
if they get sent out in response to the drm_vblank_off(). It's better
to send the very latest timestamp and count instead.
Testcase: igt/kms_flip/modeset-vs-vblank-race
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Drop the drm_vblank_off() (Daniel)
Use drm_crtc_vblank_{get,put}()
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure drm_vblank_get() never succeeds when called between
drm_vblank_off() and drm_vblank_on(). Borrow a trick from the
old drm_vblank_{pre,post}_modeset() functions and just bump
the refcount in drm_vblank_off() and drop it in drm_vblank_on().
When drm_vblank_get() encounters a >0 refcount and the vblank
interrupt is already disabled it will simply return -EINVAL.
Hopefully the use of inmodeset won't conflict badly with
drm_vblank_{pre,post}_modeset().
For i915 there's a window between drm_vblank_off() and marking the
crtc as inactive where the current code still allows drm_vblank_get().
v2: Describe what drm_vblank_get() does to explain how
a simple refcount bump manages to fix things (Daniel)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After spending slightly more time than I'd care to admit debugging the
various and presumably spectacular way things fail when you pass too low
a value to drm_vblank_init() (thanks console-lock for not letting me see
the carnage!), I decided it might be a good idea to add some sanity
checking.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add drm_panel controls to support powerup/down of the
eDP panel, if one is present at the sink side.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add commit callback for exynos_dp, and move the DP link training,
video configuration code from the hotplug handler into commit().
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B133HTN01 is a 13.6" FHD TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
This panel is used on the Samsung Chromebook 2 (XE503C32).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For most of the panels, we need to provide delays during various stages
of panel power up and power down. Add a structure to hold those delay
values and use them in corresponding functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move out code from enable and disable routines to prepare
and unprepare routines, so that functionality is properly
distributed across all the panel functions.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify tegra output driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify exynos_dsi driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify exynos_dpi driver to support the new panel calls:
prepare and unprepare.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
simple-panel is not a valid panel model, so there is no data (video
timings, etc.) associated with it. Therefore drivers can't do anything
useful with it, so it should not appear in the table of OF matches.
Device trees will always need to specify the exact model of the panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux N116BGE is an 11.6" WXGA TFT LCD panel connecting to an eDP
interface and with an integrated LED backlight unit.
It is used in the Tegra132 Norrin reference design.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Warn when there are events on the file_priv->event_list just before
file_priv gets freed. This can occur if the driver doesn't clean up
pending page flip events in ->preclose().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
i915.ko has a custom fbdev initialisation routine that aims to preserve
the current mode set by the BIOS, unless overruled by the user. The
user's wishes are determined by what, if any, mode is specified on the
command line (via the video= parameter). However, that command line mode
is first parsed by drm_fb_helper_initial_config() which is called after
i915.ko's custom initial_config() as a fallback method. So in order for
us to honour it, we need to move the cmdline parser earlier. If we
perform the connector cmdline parsing as soon as we initialise the
connector, that cmdline mode and forced status is then available even if
the fbdev helper is not compiled in or never called.
We also then expose the cmdline user mode in the connector mode lists.
v2: Rebase after connector->name upheaval.
v3: Adapt mga200 to look for the cmdline mode in the new place. Nicely
simplifies things while at that.
v4: Fix checkpatch.
v5: Select FB_CMDLINE to adapt to the changed fbdev patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73154
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Cc: dri-devel@lists.freedesktop.org
Cc: Julia Lemire <jlemire@matrox.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
