We can't have preemption disabled when we call schedule(). Accept the
possibility that we'll get preempted, and it'll cost us some cacheline
bounces.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
If the user sends a fatal signal, sleeping in the TASK_KILLABLE state
permits the task to be aborted. The only wrinkle is making sure that
if/when the command completes later that it doesn't upset anything.
Handle this by setting the data pointer to 0, and checking the value
isn't NULL in the sync completion path. Eventually, bios can be cancelled
through this path too. Note that the cmdid isn't freed to prevent reuse.
We should also abort the command in the future, but this is a good start.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Because I wasn't setting driverfs_dev, the devices were showing up under
/sys/devices/virtual/block. Now they appear underneath the PCI device
which they belong to.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
In case the card has been left in a partially-configured state,
write 0 to the Enable bit.
Signed-off-by: Shane Michael Matthews <shane.matthews@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Call pci_enable_device_mem() at initialisation and pci_disable_device
at exit.
Signed-off-by: Shane Michael Matthews <shane.matthews@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Factor out most of nvme_identify() into a new nvme_submit_user_admin_command()
function. Change nvme_get_range_type() to call it and change nvme_ioctl to
realise that it's getting back all 64 ranges.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Generalise the code from nvme_identify() that sets PRP1 & PRP2 so that
it's usable for commands sent by nvme_submit_bio_queue().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
The admin IRQ is supposed to use the pin-based (or single message MSI)
interrupt. Accomplish this by filling in entry[0]'s vector with the
INTx irq number.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Two callers with an almost identical long string of arguments, and
introducing a third soon. Time to factor out the commonalities.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Based on a patch by Mark Wu <dwu@redhat.com>
Current index allocation in virtio-blk is based on a monotonically
increasing variable "index". This means we'll run out of numbers
after a while. It also could cause confusion about the disk
name in the case of hot-plugging disks.
Change virtio-blk to use ida to allocate index, instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We want to remove the implicit everywhere presence of module.h
so fix up the people relying on that implicit presence in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting <linux/module.h> via an implicit include
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Based on a patch by Mark Wu <dwu@redhat.com>
Current index allocation in virtio-blk is based on a monotonically
increasing variable "index". This means we'll run out of numbers
after a while. It also could cause confusion about the disk
name in the case of hot-plugging disks.
Change virtio-blk to use ida to allocate index, instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix double-free of page vector
ceph: fix 32-bit ino numbers
libceph: force resend of osd requests if we skip an osdmap
ceph: use kernel DNS resolver
ceph: fix ceph_monc_init memory leak
ceph: let the set_layout ioctl set single traits
Revert "ceph: don't truncate dirty pages in invalidate work thread"
ceph: replace leading spaces with tabs
libceph: warn on msg allocation failures
libceph: don't complain on msgpool alloc failures
libceph: always preallocate mon connection
libceph: create messenger with client
ceph: document ioctls
ceph: implement (optional) max read size
ceph: rename rsize -> rasize
ceph: make readpages fully async
The xenbus module provides xenbus_map_ring_valloc() and
xenbus_map_ring_vfree(). Use these to map the ring pages granted by
the frontend.
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This simplifies the init/shutdown paths, and makes client->msgr available
during the rest of the setup process.
Signed-off-by: Sage Weil <sage@newdream.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
* 'stable/bug.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m/debugfs: Make type_name more obvious.
xen/p2m/debugfs: Fix potential pointer exception.
xen/enlighten: Fix compile warnings and set cx to known value.
xen/xenbus: Remove the unnecessary check.
xen/irq: If we fail during msi_capability_init return proper error code.
xen/events: Don't check the info for NULL as it is already done.
xen/events: BUG() when we can't allocate our event->irq array.
* 'stable/mmu.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Fix selfballooning and ensure it doesn't go too far
xen/gntdev: Fix sleep-inside-spinlock
xen: modify kernel mappings corresponding to granted pages
xen: add an "highmem" parameter to alloc_xenballooned_pages
xen/p2m: Use SetPagePrivate and its friends for M2P overrides.
xen/p2m: Make debug/xen/mmu/p2m visible again.
Revert "xen/debug: WARN_ON when identity PFN has no _PAGE_IOMAP flag set."
The P600 requires a small delay when changing states. Otherwise we may think
the board did not reset and we bail. This for kdump only and is particular
to the P600.
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are two windows of opportunity to cause a race when
processing a barrier request. This patch fixes this.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Currently the loop device tries to call directly into write_begin/write_end
instead of going through ->write if it can. This is a fairly nasty shortcut
as write_begin and write_end are only callbacks for the generic write code
and expect to be called with filesystem specific locks held.
This code currently causes various issues for clustered filesystems as it
doesn't take the required cluster locks, and it also causes issues for XFS
as it doesn't properly lock against the swapext ioctl as called by the
defragmentation tools. This in case causes data corruption if
defragmentation hits a busy loop device in the wrong time window, as
reported by RH QA.
The reason why we have this shortcut is that it saves a data copy when
doing a transformation on the loop device, which is the technical term
for using cryptoloop (or an XOR transformation). Given that cryptoloop
has been deprecated in favour of dm-crypt my opinion is that we should
simply drop this shortcut instead of finding complicated ways to to
introduce a formal interface for this shortcut.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The patch titled: "xen/blkback: Fix the inhibition to map pages
when discarding sector ranges." had the right idea except that
it used the wrong comparison operator. It had == instead of !=.
This fixes the bug where all (except discard) operations would
have been ignored.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This function was used to broadcast the (leading part of the)
bio payload in case we see a data integrity error. It could be received
from userland with the drbdsetup events subcommand,
to have a peek into the payload that caused the checksum mismatch,
and guess from there what may have caused the mismatch,
mainly to guess wether it was modification of in-flight data,
or data corruption by broken hardware or software bugs.
Meanwhile we support bios that are larger than the maximum payload a
netlink datagram can carry.
And we have means to reliably detect modification of in-flight data by
calculating, and comparing, the checksum before and after sendmsg.
There is no need to carry this around anymore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Still missing: rcu_readlock() on the various call sites that
access/iterate over those idrs.
We don't need a specific write lock, as we only modify from
configuration context, which is already strictly serialized.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Don't rely on availability of bios from the global fs_bio_set,
we should use our own bio_set for meta data IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit got it wrong:
drbd: Make the peer_seq updating code more obvious
Make it more clear that update_peer_seq() is supposed to wake up the
seq_wait queue whenever the sequence number changes.
We don't need to wake up everytime we receive a sequence number
that is _different_ from our currently stored "newest" sequence number,
but only if we receive a sequence number _newer_ than what we already
have, when we actually change mdev->peer_seq.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
