Now that the clock driver supports PLL6 and MBUS on sun8i correctly,
add the corresponding clock nodes to the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock driver has unified support for the ahb1 clock.
Unify the clock nodes so it works.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock driver has unified support for the ahb1 clock.
Unify the clock nodes so it works.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
usbphy0 support in the sunxi usb-phy driver has been merged, but the
dtsi's for sun4i/sun5i haven't been updated. This results in the phy
driver failing to load, breaking usb support.
Fixes: 6827a46f59 ('phy: sun4i: add support for USB phy0')
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that ever since (536f6b9 mmc: dw_mmc: Reset DMA before
enabling IDMAC) landed upstream that SD cards have been very unhappy
on rk3288-evb. They were a little unhappy before that change, but
after that change they're REALLY unhappy.
It turns out that the above fix happens to fix a corruption when
reading card information during probe time. Without the fix we didn't
detect that high speed SD cards could actually support high speed.
With the fix we suddenly detect that they're high speed and we try to
use them at 50MHz. That doesn't work so well on EVB with the default
drive strength (maybe because there are two physical SD card slots
hooked up to the same pin?).
Fix the problem by bumping up the drive strength of the sdmmc lines.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Fixes: 536f6b91d2 ("mmc: dw_mmc: Reset DMA before enabling IDMAC")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
All of mmc controllers include SDMMC, SDIO0, SDIO1, and EMMC on RK3288
are limited to 150Mhz. It was mainly caused by two reasons:
- RK3288's IO pad(except DDR IO pad) is generic, which can only support
the max of 150Mhz.
- Mmc controller was designed at 150Mhz, and the pressure test by IC team
was based on this freequency point.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables the cpufreq-dt driver in mvebu_v7_defconfig, as it
is used on Armada XP platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This patch enables the phy drivers for the SATA controller on Marvell's 88f6192.
Without them it is not possible to use SATA drives attached to this processor.
Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Iomega ix2-200 can be powered off via GPIO 0 pin 17,
this patch wires up the gpio-poweroff driver to do it.
Signed-off-by: Richard Kunze <richard.kunze@web.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The original MTD partition layout for the Iomega ix2-200 leaves most of the
available space unused. This patch changes the layout to use all remaining
MTD space after the partitions for u-boot/u-boot-env and the kernel uimage
as a "rootfs" partition.
Signed-off-by: Richard Kunze <richard.kunze@web.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The commit b4607572ef (ARM: mvebu: remove conflicting muxing on
Armada 370 DB) removes the hog pins muxing. As it is explained in the
commit log it solves a warning a boot time, but more important it also
allows using the Giga port 0 of the board.
Unfortunately in the same time the commit 4904a82a93 (arm: mvebu:
move Armada 370/XP pinctrl node definition armada-370-xp.dtsi) was
merged and it introduced again the hog pins muxing. Because of it, the
Giga port 0 of the board is no more usable.
This commit remove again the conflicting muxing (hopefully for the
last time).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[andrew@lunn.ch: Correct commit IDs]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 4904a82a93 ("arm: mvebu: move Armada 370/XP pinctrl node definition armada-370-xp.dtsi")
The vdso base address has always been randomized, and I don't think there's
anything particularly wrong with the range over which it's randomized,
but the implementation seems to have been buggy since the very beginning.
This fixes the implementation to remove a large bias that caused a small
fraction of possible vdso load addresess to be vastly more likely than
the rest of the possible addresses.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUlhwwAAoJEK9N98ZeDfrklIcH/2/4P/ffRcCp0qYo7gFpXwPh
bWem3ygB4xmBgiivwGJOx/GgE6/QGmedZmD6EDLoLmpuOvGjdp4iRmvU1dCSDWOE
bMOBa1cxC4TPGzqlbGgjmyHgMPuihJq6GInAqmpJk/hZJ8W7JfnXyoZbt9pj4UBW
gYKMLa0gSF/rMTZ5hkDQ6mVH65M7jJnmHLRydTpK8Ryfap2lu01MIr6mC6xaobVc
5NfbI8bZexQECGLmPsFRnFWrYXNz86PKtN0j4YnPRVPRbBSTi8nHGu+zK2CJXpgu
9hyZ0eOdqSEi4wwQgI9g9lZSsa1C+5QBc6BwiDy5XjToPJOx5EnT6+m9O+fy9Q8=
=BVMi
-----END PGP SIGNATURE-----
Merge tag 'pr-20141220-x86-vdso' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux into x86/urgent
Pull a VDSO fix from Andy Lutomirski:
"One vdso fix for a longstanding ASLR bug that's been in the news lately.
The vdso base address has always been randomized, and I don't think there's
anything particularly wrong with the range over which it's randomized,
but the implementation seems to have been buggy since the very beginning.
This fixes the implementation to remove a large bias that caused a small
fraction of possible vdso load addresess to be vastly more likely than
the rest of the possible addresses."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The LAN9220 VDDVARIO supply is powered by a 1.8V source, not 3.3V. Fix
it in the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Makes sure the dtb is built for multiplatform builds.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This moves everything to the legacy dts that is missing there in
preparation for the switch to multiplatform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when r8a7779 CCF is in place we can hook up
the ARM Cortex-A9 TWD timer via DTS.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up MSTP clocks to SCIF devices on r8a7779 to allow
clock gating to work as expected.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use R8A7779_CLK_P as parent clock for SCIF devices on r8a7779.
With this change in place the SCIF CCF handling matches the
legacy clock code. Also, this matches the data sheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to change into mode3, CPOL and CPHA bit of SPCMD register
of QSPI is changed. Mode3 can avoid intermediate voltage.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
[horms: Updated changelog and re-ordered properties]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Skip the TWD setup in C for r8a7779 Multiplatform.
We should use DTS for the TWD device anyway.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fix "is_e2" warning introduced by:
9ce3fa6 ARM: shmobile: rcar-gen2: Add CA7 arch_timer initialization for r8a7794
Only triggers on kernel configurations that have ARCH_ARM_TIMER=n.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since commit FIXME ("ARM: shmobile: lager: Remove legacy board support"),
lager is restricted to booting from DT, so chosen/stdout-path is always
used, and we can drop the "console=" parameter from chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's no reason to name the only two available serial ports on the
board ttySC6 and ttySC7 (apart from confusing userspace, which we should
try to avoid).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's no reason to name the only two available serial ports on the
board ttySC6 and ttySC7 (apart from confusing userspace, which we should
try to avoid).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7790 boards are now used with multiplatform kernels only. We can
remove all the unused r8a7790 legacy device and clock registration code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lager legacy support level is same as the DT case
so remove the legacy code and force people to move
over to using Multiplatform and DT.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[Remove lager_defconfig and don't build the dtb for legacy kernels]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove redundant C board code for Lager Multiplatform,
everything is supported via DT these days anyway so it
is fine to rely on the MACHINE_START in setup-r8a7790.c.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[Remove CONFIG_MACH_LAGER from shmobile_defconfig]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to change into mode3, CPOL and CPHA bit of SPCMD register
of QSPI is changed. Mode3 can avoid intermediate voltage.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
[horms: Updated changelog and re-ordered properties]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car E2 (r8a7794) contains two Cortex-A7 cores, hence the second
interrupt specifier cell for Private Peripheral Interrupts should use
"GIC_CPU_MASK_SIMPLE(2)".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car M2-W (r8a7791) contains two Cortex-A15 cores, hence the second
interrupt specifier cell for Private Peripheral Interrupts should use
"GIC_CPU_MASK_SIMPLE(2)".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the size and names of flash partitions to match the
expectations of the loader which are as follows:
"loader"---0x0000_0000-0x0008_0000 [loader program (readonly)]
"user" ---0x0008_0000-0x0060_0000 [U-Boot + bootargs + dt + uImage (readonly)]
"flash" ---0x0060_0000-0x0400_0000 [filesystem and free (read/write)]
["user"'s assumed breakdown]
U-boot (0x0008_0000-0x000c_0000) 256KiB
bootargs (0x000c_0000-0x0010_0000) 256KiB
Device tree (0x0010_0000-0x0014_0000) 256KiB
zImage (0x0014_0000-0x0060_0000) 4.75MiB
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
With the addition of clock-indices in commit 8e33f91a0b ("clk:
shmobile: clk-mstp: change to using clock-indices"), we can change the
DTSes to use the generic property instead of the deprecated
vendor-specific property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With the addition of clock-indices in commit 8e33f91a0b ("clk:
shmobile: clk-mstp: change to using clock-indices"), we can change the
DTSes to use the generic property instead of the deprecated
vendor-specific property.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[geert: Extracted r8a7791-specific part, rebased, reworded]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
