When the compiler doesn't support gcc plugins (either due to missing
headers or too old a version), report the problem and abort the build
instead of emitting a warning and letting the build founder with arcane
compiler errors.
Signed-off-by: Kees Cook <keescook@chromium.org>
According to E-EDID spec 1.3, table 3.9, a digital video sink with the
"DFP 1.x compliant TMDS" bit set is "signal compatible with VESA DFP 1.x
TMDS CRGB, 1 pixel / clock, up to 8 bits / color MSB aligned".
For such displays, the DFP spec 1.0, section 3.10 "EDID support" says:
"If the DFP monitor only supports EDID 1.X (1.1, 1.2, etc.)
without extensions, the host will make the following assumptions:
1. 24-bit MSB-aligned RGB TFT
2. DE polarity is active high
3. H and V syncs are active high
4. Established CRT timings will be used
5. Dithering will not be enabled on the host"
So if we don't know the bit depth of the display from additional
colorimetry info we should assume 8 bpc / 24 bpp by default.
This patch adds info->bpc = 8 assignement for that case.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown")
This commit introduced a regression into stable kernels,
as it reduces output color depth to 6 bpc for any video
sink connected to a Displayport connector if that sink
doesn't report a specific color depth via EDID, or if
our EDID parser doesn't actually recognize the proper
bpc from EDID.
Affected are active DisplayPort->VGA converters and
active DisplayPort->DVI converters. Both should be
able to handle 8 bpc, but are degraded to 6 bpc with
this patch.
The reverted commit was meant to fix
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
A followup patch implements a fix for that specific bug,
which is caused by a faulty EDID of the affected DP panel
by adding a new EDID quirk for that panel.
DP 18 bpp fallback handling and other improvements to
DP sink bpc detection will be handled for future
kernels in a separate series of patches.
Please backport to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=yN6a
-----END PGP SIGNATURE-----
Merge tag 'lkdtm-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull lkdtm update from Kees Cook:
"Fix rebuild problem with LKDTM's rodata test"
[ This, and the usercopy branch, both came in before the merge window
closed, but ended up in my 'need to look more' queue and thus got
merged only after rc1 was out ]
* tag 'lkdtm-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lkdtm: Fix targets for objcopy usage
lkdtm: fix false positive warning from -Wmaybe-uninitialized
There are multiple cases in vfio_pci_set_ctx_trigger_single() where
we assume we can safely read from our data pointer without actually
checking whether the user has passed any data via the count field.
VFIO_IRQ_SET_DATA_NONE in particular is entirely broken since we
attempt to pull an int32_t file descriptor out before even checking
the data type. The other data types assume the data pointer contains
one element of their type as well.
In part this is good news because we were previously restricted from
doing much sanitization of parameters because it was missed in the
past and we didn't want to break existing users. Clearly DATA_NONE
is completely broken, so it must not have any users and we can fix
it up completely. For DATA_BOOL and DATA_EVENTFD, we'll just
protect ourselves, returning error when count is zero since we
previously would have oopsed.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Chris Thompson <the_cartographer@hotmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Commit 52253db924 ("sctp: also point GSO head_skb to the sk when
it's available") used event->chunk->head_skb to get the head_skb in
sctp_ulpevent_set_owner().
But at that moment, the event->chunk was NULL, as it cloned the skb
in sctp_ulpevent_make_rcvmsg(). Therefore, that patch didn't really
work.
This patch is to move the event->chunk initialization before calling
sctp_ulpevent_receive_data() so that it uses event->chunk when it's
valid.
Fixes: 52253db924 ("sctp: also point GSO head_skb to the sk when it's available")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan driver has bypass for local vxlan traffic, but that
depends on information about all VNIs on local system in
vxlan driver. This is not available in case of LWT.
Therefore following patch disable encap bypass for LWT
vxlan traffic.
Fixes: ee122c79d4 ("vxlan: Flow based tunneling").
Reported-by: Jakub Libosvar <jlibosva@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LWT user can specify destination as well as source ip address
for given tunnel endpoint. But vxlan is ignoring given source
ip address. Following patch uses both ip address to route the
tunnel packet. This consistent with other LWT implementations,
like GENEVE and GRE.
Fixes: ee122c79d4 ("vxlan: Flow based tunneling").
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
Few BPF helper related checksum fixes
The set contains three fixes with regards to CHECKSUM_COMPLETE
and BPF helper functions. For details please see individual
patches.
Thanks!
v1 -> v2:
- Fixed make htmldocs issue reported by kbuild bot.
- Rest as is.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When having skbs on ingress with CHECKSUM_COMPLETE, tc BPF programs don't
push rcsum of mac header back in and after BPF run back pull out again as
opposed to some other subsystems (ovs, for example).
For cases like q-in-q, meaning when a vlan tag for offloading is already
present and we're about to push another one, then skb_vlan_push() pushes the
inner one into the skb, increasing mac header and skb_postpush_rcsum()'ing
the 4 bytes vlan header diff. Likewise, for the reverse operation in
skb_vlan_pop() for the case where vlan header needs to be pulled out of the
skb, we're decreasing the mac header and skb_postpull_rcsum()'ing the 4 bytes
rcsum of the vlan header that was removed.
However mangling the rcsum here will lead to hw csum failure for BPF case,
since we're pulling or pushing data that was not part of the current rcsum.
Changing tc BPF programs in general to push/pull rcsum around BPF_PROG_RUN()
is also not really an option since current behaviour is ABI by now, but apart
from that would also mean to do quite a bit of useless work in the sense that
usually 12 bytes need to be rcsum pushed/pulled also when we don't need to
touch this vlan related corner case. One way to fix it would be to push the
necessary rcsum fixup down into vlan helpers that are (mostly) slow-path
anyway.
Fixes: 4e10df9a60 ("bpf: introduce bpf_skb_vlan_push/pop() helpers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to commit f8ffad69c9 ("bpf: add skb_postpush_rcsum and fix
dev_forward_skb occasions") to fix an issue for dev_queue_xmit() redirect
locations which need CHECKSUM_COMPLETE fixups on ingress.
For the same reasons as described in f8ffad69c9 already, we of course
also need this here, since dev_queue_xmit() on a veth device will let us
end up in the dev_forward_skb() helper again to cross namespaces.
Latter then calls into skb_postpull_rcsum() to pull out L2 header, so
that netif_rx_internal() sees CHECKSUM_COMPLETE as it is expected. That
is, CHECKSUM_COMPLETE on ingress covering L2 _payload_, not L2 headers.
Also here we have to address bpf_redirect() and bpf_clone_redirect().
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call site for this function appears as:
#ifdef DEBUG
data->msg_enable = DEBUG;
dump_eth_one(dev);
#endif
...leading to the following warning for !DEBUG builds:
drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
static void dump_eth_one(struct net_device *dev)
^
...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig
Put the function definition under the same #ifdef as the call site
to avoid the warning.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low-level resume-from-hibernation code on x86-64 uses
kernel_ident_mapping_init() to create the temoprary identity mapping,
but that function assumes that the offset between kernel virtual
addresses and physical addresses is aligned on the PGD level.
However, with a randomized identity mapping base, it may be aligned
on the PUD level and if that happens, the temporary identity mapping
created by set_up_temporary_mappings() will not reflect the actual
kernel identity mapping and the image restoration will fail as a
result (leading to a kernel panic most of the time).
To fix this problem, rework kernel_ident_mapping_init() to support
unaligned offsets between KVA and PA up to the PMD level and make
set_up_temporary_mappings() use it as approprtiate.
Reported-and-tested-by: Thomas Garnier <thgarnie@google.com>
Reported-by: Borislav Petkov <bp@suse.de>
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
When I initially added the unsafe_[get|put]_user() helpers in commit
5b24a7a2aa ("Add 'unsafe' user access functions for batched
accesses"), I made the mistake of modeling the interface on our
traditional __[get|put]_user() functions, which return zero on success,
or -EFAULT on failure.
That interface is fairly easy to use, but it's actually fairly nasty for
good code generation, since it essentially forces the caller to check
the error value for each access.
In particular, since the error handling is already internally
implemented with an exception handler, and we already use "asm goto" for
various other things, we could fairly easily make the error cases just
jump directly to an error label instead, and avoid the need for explicit
checking after each operation.
So switch the interface to pass in an error label, rather than checking
the error value in the caller. Best do it now before we start growing
more users (the signal handling code in particular would be a good place
to use the new interface).
So rather than
if (unsafe_get_user(x, ptr))
... handle error ..
the interface is now
unsafe_get_user(x, ptr, label);
where an error during the user mode fetch will now just cause a jump to
'label' in the caller.
Right now the actual _implementation_ of this all still ends up being a
"if (err) goto label", and does not take advantage of any exception
label tricks, but for "unsafe_put_user()" in particular it should be
fairly straightforward to convert to using the exception table model.
Note that "unsafe_get_user()" is much harder to convert to a clever
exception table model, because current versions of gcc do not allow the
use of "asm goto" (for the exception) with output values (for the actual
value to be fetched). But that is hopefully not a limitation in the
long term.
[ Also note that it might be a good idea to switch unsafe_get_user() to
actually _return_ the value it fetches from user space, but this
commit only changes the error handling semantics ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ido Schimmel says:
====================
mlxsw: DCB fixes
Patches 1 and 2 fix a problem in which PAUSE frames settings are wrongly
overridden when ieee_setpfc() gets called.
Patch 3 adds a missing rollback in port's creation error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.
Fixes: f00817df2b ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).
Fix this by packing the PFCC register with the current PAUSE settings.
Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ieee_setpfc() gets called, PAUSE frames are not necessarily
disabled on the port.
Check if PAUSE frames are disabled or enabled and configure the port's
headroom buffer accordingly.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a simple copy'n'paste error.
Fixes: 1aa661f5c3 ("rhashtable-test: Measure time to insert, remove & traverse entries")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter says:
====================
sctp_diag: A bunch of fixes for upcoming 'ss' support
The following series contains a number of fixes necessary to make my yet
unpublished 'ss' support patch functional.
Changes since v1:
- Fixed patch 2/3
- Rebased whole series onto current net-next/master
Changes since v2:
- Improved description of patch 2/3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 'ss' always adds TCPF_CLOSE to idiag_states flags, sctp_diag can't
rely upon TCPF_LISTEN flag solely being present when listening sockets
are requested.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asoc's timer value is not kept in asoc->timeouts array but in it's
primary transport instead.
Furthermore, we must export the timer only if it is pending, otherwise
the value will underrun when stored in an unsigned variable and
user space will only see a very large timeout value.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to correctly interpret INET_DIAG_INFO messages exported
by sctp_diag module.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Purely cosmetic at this point, as rbd doesn't use RADOS namespaces and
hence rbd_dev->header_oloc->pool_ns is always NULL.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Fixes the following sparse warning:
net/ceph/mon_client.c:577:6: warning:
symbol 'cancel_generic_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In case of error, the function ceph_alloc_page_vector() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Fixes: 1907920324 ('libceph: support for sending notifies')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In commit 874f9c7da9 ("printk: create pr_<level> functions"), new
pr_level defines were added to printk.c.
These new defines are guarded by an #ifdef CONFIG_PRINTK - however,
there is already a surrounding #ifdef CONFIG_PRINTK starting a lot
earlier in line 249 which means the newly introduced #ifdef is
unnecessary.
Let's remove it to avoid confusion.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WMI event 0xe00e is received when battery was removed or inserted.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
To be consistent with other namespaces, expose a 'size' attribute for
BTT devices also.
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The "NVDIMM Block Window Driver Writer's Guide":
http://pmem.io/documents/NVDIMM_DriverWritersGuide-July-2016.pdf
...defines the layout of the block window status register. For the July
2016 version of the spec linked to above, this happens in Figure 4 on
page 26.
The only bits defined in this spec are bits 31, 5, 4, 2, 1 and 0. The
rest of the bits in the status register are reserved, and there is a
warning following the diagram that says:
Note: The driver cannot assume the value of the RESERVED bits in the
status register are zero. These reserved bits need to be masked off, and
the driver must avoid checking the state of those bits.
This change ensures that for hardware implementations that set these
reserved bits in the status register, the driver won't incorrectly fail the
block I/Os.
Cc: <stable@vger.kernel.org> #v4.2+
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
To be able to generate shared descriptors for AEAD, the authentication size
needs to be known. However, there is no imposed order of calling .setkey,
.setauthsize callbacks.
Thus, in case authentication size is not known at .setkey time, defer it
until .setauthsize is called.
The authsize != 0 check was incorrectly removed when converting the driver
to the new AEAD interface.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are a few things missed by the conversion to the
new AEAD interface:
1 - echainiv(authenc) encrypt shared descriptor
The shared descriptor is incorrect: due to the order of operations,
at some point in time MATH3 register is being overwritten.
2 - buffer used for echainiv(authenc) encrypt shared descriptor
Encrypt and givencrypt shared descriptors (for AEAD ops) are mutually
exclusive and thus use the same buffer in context state: sh_desc_enc.
However, there's one place missed by s/sh_desc_givenc/sh_desc_enc,
leading to errors when echainiv(authenc(...)) algorithms are used:
DECO: desc idx 14: Header Error. Invalid length or parity, or
certain other problems.
While here, also fix a typo: dma_mapping_error() is checking
for validity of sh_desc_givenc_dma instead of sh_desc_enc_dma.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
crypto/sha3_generic.c:27: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:28: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:29: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:29: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:31: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:31: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:32: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:32: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:32: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:33: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:33: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:34: warning: integer constant is too large for ‘long’ type
crypto/sha3_generic.c:34: warning: integer constant is too large for ‘long’ type
Fixes: 53964b9ee6 ("crypto: sha3 - Add SHA-3 hash algorithm")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During qdio_shutdown the queue tasklets are killed for all inbound and
outbound queues. The queue structures might be freed after
qdio_shutdown.
Thus it must be guaranteed that these queue tasklets are not rescheduled
after that. In addition the outbound queue timers are deleted and it
must
be guaranteed that these timers are not restarted after qdio_shutdown
processing. Timer deletion should make use of del_timer_sync() to make
sure qdio_outbound_timer() is finished on other CPUs as well. Queue
tasklets should be scheduled in state QDIO_IRQ_STATE_ACTIVE only.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Prior to starting IO qdio checks for the internal state of the ccw
device. These checks happen without locking, so consistency between
state evaluation and starting of the IO is not guaranteed.
Since the internal state is checked during ccw_device_start it is
safe to get rid of these additional checks.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
qdio sometimes checks return codes twice. First with the ccw device's
lock held and then a 2nd time after the lock is released. Simplify
the code by releasing the lock earlier and unify the return code
evaluation.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All qdio functions that use spin_lock_irqsave are never used
from irq context. Thus it is safe to convert all of them to
use spin_lock_irq.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A copy of struct subchannel_id is maintained in ccw_device_private.
The subchannel id is a property of the subchannel. The additional
copy is not needed.
Internal users can obtain it from subchannel.schid - device drivers
can use ccw_device_get_schid().
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We want to get rid of the copy of struct subchannel_id maintained in
ccw_device_private, so obtain it using ccw_device_get_schid().
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We want to get rid of the copy of struct subchannel_id maintained in
ccw_device_private, so obtain it from the subchannel directly.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For all configs with CONFIG_BTRFS_FS = y we should also make the
optimized crc module builtin. Otherwise early mounts will fall
back to the software variant.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
if two string compare equal the clcle instruction will update the
string addresses to point _after_ the string. This might already
be on a different page, so we should not use these pointer to
calculate the difference as in that case the calculation of the
difference can cause oopses.
The return value of memcmp does not need the difference, we
can just reuse the condition code and return for CC=1 (All bytes
compared, first operand low) -1 and for CC=2 (All bytes compared,
first operand high) +1
strstr also does not need the diff.
While fixing this, make the common function clcle "correct on its
own" by using l1 instead of l2 for the first length. strstr will
call this with l2 for both strings.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: db7f5eef3d ("s390/lib: use basic blocks for inline assemblies")
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
