Commit 2549d6c2 removed the vmalloc used for temporary storage of the
relocation lists used during execbuffer. However, our use of vmalloc was
being protected by an integer overflow check which we do want to
preserve!
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the user specifies mem= on the kernel command line, some or all
of the extra memory E820 region may be clipped away, so make sure
we don't try to add more extra memory than exists in E820.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Add extra pages in the pseudo-physical address space to the balloon
so we can extend into them later.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Disabling SuperSpeed ports is a Very Bad Thing (TM). It disables
SuperSpeed terminations, which means that devices will never connect at
SuperSpeed on that port. For USB 2.0/1.1 ports, disabling the port meant
that the USB core could always get a connect status change later. That's
not true with USB 3.0 ports.
Do not let the USB core disable SuperSpeed ports. We can't rely on the
device speed in the port status registers, since that isn't valid until
there's a USB device connected to the port. Instead, we use the port
speed array that's created from the Extended Capabilities registers.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Don Zickus <dzickus@redhat.com>
Cc: stable@kernel.org
An xHCI host controller contains USB 2.0 and USB 3.0 ports, which can
occur in any order in the PORTSC registers. We cannot read the port speed
bits in the PORTSC registers at init time to determine the port speed,
since those bits are only valid when a USB device is plugged into the
port.
Instead, we read the "Supported Protocol Capability" registers in the xHC
Extended Capabilities space. Those describe the protocol, port offset in
the PORTSC registers, and port count. We use those registers to create
two arrays of pointers to the PORTSC registers, one for USB 3.0 ports, and
another for USB 2.0 ports. A third array keeps track of the port protocol
major revision, and is indexed with the internal xHCI port number.
This commit is a bit big, but it should be queued for stable because the "Don't
let the USB core disable SuperSpeed ports" patch depends on it. There is no
other way to determine which ports are SuperSpeed ports without this patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Don Zickus <dzickus@redhat.com>
Cc: stable@kernel.org
We have been having problems with the USB-IF Gold Tree tests when plugging
and unplugging devices from the tree. I have seen that the reset-device
and configure-endpoint commands, which are invoked from
xhci_discover_or_reset_device() and xhci_configure_endpoint(), will sometimes
time out.
After much debugging, I determined that the commands themselves do not actually
time out, but rather their completion events do not get delivered to the right
place.
This happens when the command ring has just wrapped around, and it's enqueue
pointer is left pointing to the link TRB. xhci_discover_or_reset_device() and
xhci_configure_endpoint() use the enqueue pointer directly as their command
TRB pointer, without checking whether it's pointing to the link TRB.
When the completion event arrives, if the command TRB is pointing to the link
TRB, the check against the command ring dequeue pointer in
handle_cmd_in_cmd_wait_list() fails, so the completion inside the command does
not get signaled.
The patch below fixes the timeout problem for me.
This should be queued for the 2.6.35 and 2.6.36 stable trees.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Some board/card/host configurations are not capable of powering off the
card after boot.
To support such configurations, and to allow smoother transition to
runtime PM behavior, MMC_CAP_POWER_OFF_CARD is added, so hosts need to
explicitly indicate whether it's OK to power off their cards after boot.
SDIO core will enable runtime PM for a card only if that cap is set.
As a result, the card will be powered down after boot, and will only
be powered up again when a driver is loaded (and then it's up to the
driver to decide whether power will be kept or not).
This will prevent sdio_bus_probe() failures with setups that do not
support powering off the card.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Reported-and-tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Power off the card in mmc_sdio_detect __before__ a potential error
handler, which completely removes the card, executes, and only if the
card was successfully powered on beforehand.
While we're at it, use the _sync variant of the runtime PM put API, in
order to ensure that the card is left powered off in case an error
occurred, and the card is going to be removed.
Reproduced and tested on the OLPC XO-1.5.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix typo in keycode validation supporting large scancodes
Input: aiptek - tighten up permissions on sysfs attributes
Input: sysrq - pass along lone Alt + SysRq
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Disable FBC on Ironlake to save 1W
drm/i915: Take advantage of auto-polling CRT hotplug detection on PCH hardware
drm/i915/crt: Introduce struct intel_crt
drm/i915: Do not hold mutex when faulting in user addresses
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
drm/i915: Retire any pending operations on the old scanout when switching
drm/i915: Fix I2C adapter registration
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (40 commits)
drm/radeon/kms: i2c s/sprintf/snprintf/g for safety
drm/radeon/kms: fix i2c pad masks on rs4xx
drm/ttm: Fix up a theoretical deadlock
drm/radeon/kms: fix tiling info on evergreen
drm/radeon/kms: fix alignment when allocating buffers
drm/vmwgfx: Fix up an error path during bo creation
drm/radeon/kms: register an i2c adapter name for the dp aux bus
drm/radeon/kms/atom: add proper external encoders support
drm/radeon/kms/atom: cleanup and unify DVO handling
drm/radeon/kms: properly power up/down the eDP panel as needed (v4)
drm/radeon/kms/atom: set sane defaults in atombios_get_encoder_mode()
drm/radeon/kms: turn the backlight off explicitly for dpms
drm/radeon/kms: fix typo in r600 cs checker
drm: radeon: fix error value sign
drm/radeon/kms: fix and unify tiled buffer alignment checking for r6xx/7xx
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
...
vt6420 has the same FIFO overflow problem as vt6421 when combined with
certain devices. This patch applies the magic fix to vt6420 too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Qvist <q@maq.dk>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
winbond drivers use msleep() and delay(), so include linux/delay.h
in a common header file to prevent build errors.
drivers/staging/winbond/phy_calibration.c:987: error: implicit declaration of function 'msleep'
drivers/staging/winbond/phy_calibration.c:1556: error: implicit declaration of function 'udelay'
drivers/staging/winbond/reg.c:894: error: implicit declaration of function 'msleep'
drivers/staging/winbond/reg.c:1178: error: implicit declaration of function 'udelay'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since interrupts are enabled only when open is called on the interface,
Attempting a firmware update operation when interface is down could lead to
partial success or failure of operation. This fix fails the request if
netif_running is false.
Signed-off-by: Sarveshwar Bandi <Sarveshwar.Bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 45aafd3299 "UBI: tighten the corrupted PEB criteria"
introduced some return paths that didn't release the ubi->buf_mutex
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Frame buffer compression is broken on Ironlake due to buggy hardware.
Currently it is disabled through chicken bits, but it still consumes
over 1W more than if we simply never attempt to enable the FBC code
paths.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We will use this structure in future patches to store CRT specific
information on the encoder.
Split out and tweaked from a patch by Keith Packard.
Signed-off-by: Keith Packard <keithp@kithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Linus Torvalds found that it was rather trivial to trigger a system
freeze:
In fact, with lockdep, I don't even need to do the sysrq-d thing: it
shows the bug as it happens. It's the X server taking the same lock
recursively.
Here's the problem:
=============================================
[ INFO: possible recursive locking detected ]
2.6.37-rc2-00012-gbdbd01a #7
---------------------------------------------
Xorg/2816 is trying to acquire lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c626c>] i915_gem_fault+0x50/0x17e
but task is already holding lock:
(&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
other info that might help us debug this:
2 locks held by Xorg/2816:
#0: (&dev->struct_mutex){+.+.+.}, at: [<ffffffff812c403b>] i915_mutex_lock_interruptible+0x28/0x4a
#1: (&mm->mmap_sem){++++++}, at: [<ffffffff81022d4f>] page_fault+0x156/0x37b
This recursion was introduced by rearranging the locking to avoid the
double locking on the fast path (4f27b5d and fbd5a26d) and the
introduction of the prefault to encourage the fast paths (b5e4f2b). In
order to undo the problem, we rearrange the code to perform the access
validation upfront, attempt to prefault and then fight for control of the
mutex. the best case scenario where the mutex is uncontended the
prefaulting is not wasted.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The disabling of the init op for non-legacy clocks neglected to do the
same in the core clock framework, resulting in a build failure. Fix it
up.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* xen/dev-evtchn:
xen/evtchn: add missing static
xen/evtchn: Fix name of Xen event-channel device
xen/evtchn: don't do unbind_from_irqhandler under spinlock
xen/evtchn: remove spurious barrier
xen/evtchn: ports start enabled
xen/evtchn: dynamically allocate port_user array
xen/evtchn: track enabled state for each port
This reverts commit 24a89b5be4.
We should no longer need an address space now that we're correctly
setting VM_PFNMAP on our vmas.
Conflicts:
drivers/xen/xenfs/super.c
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
As per advice from Jean Delvare.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] remove SCSI host lock and serial number usage from ata_scsi_queuecmd
Kernel build fail for cx25821-video has depends on smp_lock.h header
file, but the dependency is removed in recent commit 451a3c24b0.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Markus Grabner <grabner@icg.tugraz.at>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Bernie Thompson <bernie@plugable.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Barry Song <Barry.Song@analog.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Taht <d@teklibre.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They should be writable by root, not readable.
Doh, stupid me with the wrong flags.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jakub Schmidtke <sjakub@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
VORTEX_PCI() could return NULL so it needs to be casted before
accessing any member of struct pci_dev. This fixes following
build failure. Likewise VORTEX_EISA() was changed also.
CC [M] drivers/net/3c59x.o
drivers/net/3c59x.c: In function 'acpi_set_WOL':
drivers/net/3c59x.c:3211:39: warning: dereferencing 'void *' pointer
drivers/net/3c59x.c:3211:39: error: request for member 'current_state' in something not a structure or union
make[3]: *** [drivers/net/3c59x.o] Error 1
make[2]: *** [drivers/net/3c59x.o] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipg.c:
The id [SUNDANCE, 0x1021] (=[0x13f0, 0x1021]) is defined
at dl2k.h and ipg.c.
But this device works better with dl2k driver.
This problem is similar with the commit
[25cca53527
ipg: Remove device claimed by dl2k from pci id table]
at 11 Feb 2010.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev() is not checked here for NULL return value. dev is
check instead. It might lead to NULL dereference of ndev.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting tid information in the TX header is required only for QoS
frames. Not handling this case causes severe data loss with some APs.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RCU conversion in IGMP code done in net-next-2.6 raised a race in
__bond_resend_igmp_join_requests().
It iterates in_dev->mc_list without appropriate protection (RTNL, or
read_lock on in_dev->mc_list_lock).
Another cpu might delete an entry while we use it and trigger a fault.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the input_keymap_entry keycode size (u32) instead of the device's
(void*) when validating that keycode value can be stored in the keymap.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=22722
Signed-off-by: Mattia Dongili <malattia@linux.it>
Tested-by: Norbert Preining <preining@logic.at>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A process suspended waiting for a higher sequence or no sequence to unreserve,
a bo may be beaten to the reservation by a process with a lower sequence.
In that case the first process should give up trying to reserve and
return -EAGAIN. In order for that to happen, we must wake waiting processes
when we change sequence, so that they have a chance to detect the new
sequence.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: (25 commits)
nouveau: Acknowledge HPD irq in handler, not bottom half
drm/nouveau: Fix a few confusions between "chipset" and "card_type".
drm/nouveau: don't expose backlight control when available through ACPI
drm/nouveau/pm: improve memtiming mappings
drm/nouveau: Make PCIE GART size depend on the available RAMIN space.
drm/nouveau: Return error from nouveau_gpuobj_new if we're out of RAMIN.
drm/nouveau: Fix compilation issues in nouveau_pm when CONFIG_HWMON is not set
drm/nouveau: Don't use load detection for connector polling.
drm/nv10-nv20: Fix instability after MPLL changes.
drm/nv50: implement possible workaround for NV86 PGRAPH TLB flush hang
drm/nouveau: Don't poll LVDS outputs.
drm/nouveau: Use "force" to decide if analog load detection is ok or not.
drm/nv04: Fix scanout over the 16MB mark.
drm/nouveau: fix nv40 pcie gart size
drm/nva3: fix overflow in fixed point math used for pll calculation
drm/nv10: Balance RTs expected to be accessed simultaneously by the 3d engine.
drm/nouveau: Expose some BO usage flags to userspace.
drm/nouveau: Reduce severity of the unknown getparam error.
drm/nouveau: Avoid lock dependency between ramht and ramin spinlocks.
drm/nouveau: Some random cleanups.
...
We aren't currently using tiling in userspace on evergreen,
but the info we currently return for the tiling info query
(gb_addr_config) is no adequate for userspace tiling alignment
calculations. It does not contain the bank info. Create a custom
tiling info dword with all the necessary info (num channels,
num banks, group size, row size).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were previously dropping alignment requests on the floor
when allocating buffers so we always ended up page aligned.
Certain tiling modes on 6xx+ require larger alignment which
wasn't happening before.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
