Handle IB_CM_DREQ_ERROR and IB_CM_DREQ_RECEIVED events from the CM,
instead of just printing "Unhandled CM event". In the case of
DREQ_ERROR, just ignore the event -- a TIMEWAIT_EXIT will be generated
also. For DREQ_RECEIVED, send a DREP in response to shut the
connection down cleanly.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the sg_tablesize used by SRP adjustable at module load time via a
module parameter. Calculate the corresponding IU length required to
support this.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow userspace to throttle traffic on a given connection to a target
port by adding "max_cmd_per_lun=xyz" to lower the cmd_per_lun value
set for that scsi_host.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Interrupts will always be enabled in srp_remove_one(), so
spin_lock_irq() can be used instead of spin_lock_irqsave().
Also, the loop takes target->scsi_host->host_lock, so target->state
can just be set to SRP_TARGET_REMOVED witout testing the old value.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SRP driver never sleeps while holding target_mutex, and it's just
used to protect some simple list operations, so hold times will be
short. So just convert it to a spinlock, which is smaller and faster.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
list_for_each_entry_safe() is used in one place where the list isn't
modified. So just change it to list_for_each_entry().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SCAN_WILD_CARD is indeed available from <scsi/scsi.h>, which is
already included. So get rid of private hack.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The kernel has had wait_for_completion_timeout() for a long time now.
mthca should use it to handle FW commands timing out, instead of
implementing the same thing in a much more complicated way by using
wait_for_completion() along with a timer that does complete().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Create an SRP FMR pool on HCAs that support FMRs, and use FMRs to map
gather/scatter lists that have more than one entry into a single
memory region that appears virtually contiguous to the SRP target
(which is the RDMA initiator).
This patch bails out on FMR mapping for SCSI commands where the
gather/scatter list cannot be mapped into a single FMR because there
are sub-page-sized entries in middle of the list. An unaligned
start or end of the list is OK.
Based on a patch by Vu Pham <vuhuong@mellanox.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Kernel connection management agent over InfiniBand that connects based
on IP addresses. The agent defines a generic RDMA connection
abstraction to support clients wanting to connect over different RDMA
devices.
The agent also handles RDMA device hotplug events on behalf of clients.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an address translation service that maps IP addresses to
InfiniBand GID addresses using IPoIB.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export ip_dev_find() to allow locating a net_device given an IP address.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend matching connection requests to listens in the InfiniBand CM to
include private data checks.
This allows applications to listen on the same service identifier,
with private data directing the request to the appropriate application.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide common handling for marshalling data between userspace clients
and kernel InfiniBand drivers.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Memfree firmware is in rare cases reporting WQE index == base - 1 in
receive completion with error, instead of (rq size - 1); base is 0 in
mthca. Here is a patch to avoid kernel crash and report a correct WR
id in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca does not restore the following PCI-X/PCI Express registers after reset:
PCI-X device: PCI-X command register
PCI-X bridge: upstream and downstream split transaction registers
PCI Express : PCI Express device control and link control registers
This causes instability and/or bad performance on systems where one of
these registers is set to a non-default value by BIOS.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Especially when summary code is used, we can have in-memory data
structures referencing certain nodes without them actually being readable
on the flash. Discard the nodes gracefully in that case, rather than
triggering a BUG().
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Reflect the fact that the Cell Broadband Engine supports 64k
pages by adding the bit to the CPU features.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The page size encoding passed to tlbie is incorrect for new-style
large pages. This fixes it. This doesn't affect anything on older
machines because mmu_psize_defs[psize].penc (the page size encoding)
is 0 for 4k and 16M pages (the two are distinguished by a separate "is
a large page" bit).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arm_timer() checks PF_EXITING to prevent BUG_ON(->exit_state)
in run_posix_cpu_timers().
However, for some reason it does so only for CPUCLOCK_PERTHREAD
case (which is imho wrong).
Also, this check is not reliable, PF_EXITING could be set on
another cpu without any locks/barriers just after the check,
so it can't prevent from attaching the timer to the exiting
task.
The previous patch makes this check unneeded.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_exit() clears ->it_##clock##_expires, but nothing prevents
another cpu to attach the timer to exiting process after that.
arm_timer() tries to protect against this race, but the check
is racy.
After exit_notify() does 'write_unlock_irq(&tasklist_lock)' and
before do_exit() calls 'schedule() local timer interrupt can find
tsk->exit_state != 0. If that state was EXIT_DEAD (or another cpu
does sys_wait4) interrupted task has ->signal == NULL.
At this moment exiting task has no pending cpu timers, they were
cleanuped in __exit_signal()->posix_cpu_timers_exit{,_group}(),
so we can just return from irq.
John Stultz recently confirmed this bug, see
http://marc.theaimsgroup.com/?l=linux-kernel&m=115015841413687
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the local timer interrupt happens just after do_exit() sets PF_EXITING
(and before it clears ->it_xxx_expires) run_posix_cpu_timers() will call
check_process_timers() with tasklist_lock + ->siglock held and
check_process_timers:
t = tsk;
do {
....
do {
t = next_thread(t);
} while (unlikely(t->flags & PF_EXITING));
} while (t != tsk);
the outer loop will never stop.
Actually, the window is bigger. Another process can attach the timer
after ->it_xxx_expires was cleared (see the next commit) and the 'if
(PF_EXITING)' check in arm_timer() is racy (see the one after that).
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of fixes that should prevent crashes when using netconsole and
suspend/resume. First, netconsole poll routine shouldn't run unless the
device is up; second, the NAPI poll should be disabled during suspend.
This is only an issue on sky2, because it has to have one NAPI poll
routine for both ports on dual port boards. Normal drivers use
netif_rx_schedule_prep and that checks for netif_running.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If get_user_pages() returns less pages than what we asked for, we jump
to out_unmap which will return ERR_PTR(ret). But ret can contain a
positive number just smaller than local_nr_pages, so be sure to set it
to -EFAULT always.
Problem found and diagnosed by Damien Le Moal <damien@sdl.hitachi.co.jp>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some time ago the cdrom open routine was changed so that we call the
driver's open routine before checking to see if it is read only. However,
if we discovered that a read write open was not possible and the open
flags required a writable open, we just returned -EROFS without calling
the driver's release routine. This seems to work for most cdrom drivers,
but breaks the Powerpc iSeries virtual cdrom rather badly.
This just inserts the release call in the error path to balance the call
to "->open()" done by "open_for_data()".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Well, this is not 100% if when the card fires two consecutive
interrupts. Though unlikely, it's better to protect early than seeing
some "weird" bugs one day. I proposed attached patch. If you can help to
test, that will be appreciated (I cannot see the lockdep warning on my
box somehow).
Cc: Frederik Deweerdt <deweerdt@free.fr>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In net/ieee80211/softmac/ieee80211softmac_wx.c, there is a bug that
prints extended sign information whenever the byte value exceeds
0x7f. The following patch changes the printk to use a u8 cast to limit
the output to 2 digits. This bug was first noticed by Dan Williams
<dcbw@redhat.com>. This patch applies to the current master branch
of the Linville tree.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcm43xx avoid pci_find_device
Change pci_find_device to safer pci_get_device with support for more
devices.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the heavy periodic work preemptible to avoid disabling
local IRQs for several msecs.
Signed-off-by: Michael Buesch <mb@buesch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Redesign the bcm43xx locking.
This is pre-work to get a preemptible periodic work handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attached are two small patches for include/net/ieee80211.h to prepare
for later submission of code to implement a user-space daemon that
supplies 802.11 regulatory information.
The first change adds a bit indicating that 802.11h rules are to be
applied to a channel. As discussed earlier in this list, a single bit
is unlikely to be sufficient; however, at this time I have been unable
to find any regulations implementing differences between 802.11a and
802.11h other than DFS, radar detection and passive scanning. A single
bit is thus sufficient to convey to the driver that these rules should
be obeyed.
The second change adds comments to the freq and max_power fields of
struct ieee80211_channel to indicate the units that are used.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juha Yrjola suggests that adding the string "MMC" to the
maintainers file entry will make it easier to find. Add
it to the file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hi,
this patch brings the CPCI405 board support up to date and fixes several
outstanding issues:
-add bios_fixup()
-enable RTC only when CONFIG_GEN_RTC defined
-corrected CompactPCI interrupt map
-added cpci405_early_serial_map for correct UART clocking
-removed unused code
Matthias
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the pmf irq_client functions to be safe against pmf interrupts coming
in while a client is registered/unregistered.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the kernel blindly halts all the processors and calls the
ibm,suspend-me rtas call. If the firmware is not in the correct
state, we then re-start all the processors and return. It is much
smarter to first check the firmware state, and only if it is waiting,
call the ibm,suspend-me call.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It seems that prom_init's early_cmdline_parse is broken on at least
Apple 970 xserves and IBM JS20 blades with SLOF. The firmware of these
machines returns -1 and 1 respectively when getprop is called for the
bootargs property of /chosen, causing Linux to ignore its builtin
command line in favor of a null string. This patch makes Linux use its
builtin command line if getprop returns an error or a null string.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some updates to the pmac32_defconfig to make it more useful:
- Enable LSF (large single files) since we enable LBD (large block devices)
- Enable IPSEC related options
- Enable remaining raid/dm options as modules
- Disable eth1394, I doubt any has that hardware and it has a nasty habit of
auto loading first and skewing network device numbering
- Enable dummy and tun as modules, always useful to have them around
- Enable EHCI, no wonder my usb2 disk was so slow
- Enable USB storage
- Enable ext3 acls
- Disable autofs and enable autofsv4 instead
- Enable nfs v3/v4 client and server. Dont want to be left in the dark ages
of pre v3
- Enable all crypto as modules, things like cryptsetup want some of them
I havent enabled the BCM43xx, perhaps we should now?
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the syscall path we currently have:
crclr so
mfcr r9
If we shift the crclr up we can avoid a stall on some CPUs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On non partitioned machines we currently set the HV bit in kernel space
only. It turns out we are supposed to maintain the HV bit in both user
and kernel space.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For pseries IOMMU bypass I want to be able to fall back to the regular
IOMMU ops. Do this by creating a dma_mapping_ops struct, and convert
the others while at it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allocate IOMMU tables local to the relevant node.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_to_nid returns -1 if the associativity cannot be found. This
means pcibus_to_cpumask has to be careful not to pass a negative index into
node_to_cpumask.
Since pcibus_to_node could be used a lot, and of_node_to_nid is slow (it
walks a list doing strcmps), lets also cache the node in the
pci_controller struct.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove some stale POWER3/POWER4/970 on 32bit kernel support.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Micro-optimisation - add no-minimal-toc to some more arch/powerpc Makefiles.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
