so the defconfig of the atmel continue to have the support of the network
as before
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new .bus_name to virtio_config_ops then modify virtio_net to
call through to it in an ethtool .get_drvinfo routine to report
bus_info in ethtool -i output which is consistent with other
emulated NICs and the output of lspci.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal #defines not module specific ones.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
printks should use KERN_ levels.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on original patch from Joe Perches <joe@perches.com>
Use the current logging styles.
pr_<level> conversions are now prefixed with "igb: "
Correct a defect where the trailing NTU may have been printed
on a separate line because of an interleaving hex_dump.
Remove unnecessary uses of KERN_CONT and use single pr_info()s
to avoid any possible output interleaving from other modules.
Coalesce formats as appropriate.
-v2 fix-up to make checkpatch.pl compliant and remove change to
the copyright line
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Based on the original patch from Joe Perches <joe@perches.com>
Use the current logging styles, prefix output with "ixgbevf: "
Add #define pr_fmt
Coalesce formats.
-v2 Fix-up to make checkpatch.pl compliant and remove change to
copyright line
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Based on the previous patch from Joe Perches <joe@perches.com>
Use current logging styles.
Prefix all output via #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Neaten link status dev_info.
-v2 Remove Copyright changes and fix-up patch to make it checkpatch.pl
compliant.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Previously the driver would force link without checking whether the link was
already established. This caused some inconsistencies in the LED blink rate.
Do not force link if link is already up.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch from Joe Perches.
Use the current logging styles.
pr_<level> conversions are now prefixed with "e1000e:"
Correct a couple of defects where the trailing NTU may have
been printed on a separate line because of an interleaving
hex_dump.
Remove unnecessary uses of KERN_CONT and use single pr_info()s
to avoid any possible output interleaving from other modules.
Coalesce formats as appropriate.
Remove an extra space from a broken across lines
coalescing of "Link Status " and " Change".
-v2 Remove changes to Copyright string
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Commit afc4b13d (net: remove use of ndo_set_multicast_list in
drivers) changed e1000e to use the ndo_set_rx_mode entry point,
but didn't implement the unicast address programming
functionality. Implement it to achieve the ability to add unicast
addresses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only setup structs related to debugfs_ops when CONFIG_IWLEGACY_DEBUGFS is set.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
1) remove ret local var and return the result directly
2) remove il since it is not used
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
remove the lq_sta local variable and return the
result directly in il4965_rs_alloc_sta
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
both sta and lq_sta are guaranteed to be not null in the calling
function so we don't need to check them here.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
the null check on sta in il4965_rs_tx_status is not necessary
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
When operating AP interface is brough down the mode is reset to
STA. This STA will be reconfigured into AP mode when the interface
is brought up again. This sequence will be successful only when
change_virtual_intf() returns with no error, but there is a
check in this callback which does the type change only when
that interface is active. This callback does nothing more
than saving the new interface type to vif and wdev, so the
sanity check for interface state and wmi state is not necessary.
This makes the AP interface functional again after interface down/up.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Connect control flag CONNECT_WPS_FLAG has to be cleared
by default even if the driver receives zero length IE
from cfg80211.
Otherwise this flag would be always set after WPS exchange
which would lead wpa_supplicant to fail to connect with
the received WPS credentials. This issue is observed only
in OPEN security.
kvalo: use cfg80211 instead of CFG in the commit log
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When adding ar6004 SDIO support I forgot to add corresponding
MODULE_FIRMWARE() definitions to sdio.c.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Part of ath6kl uses "REV3" style of naming hardware versions and elsewhere
"hw 2.1.1" is used instead for the same version. This is confusing, use
the latter term everywhere.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To make it easier to print name for each hardware type. Also move the hw
info print to ath6kl_init_hw_start() which is more logical place for it.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Board data address can change between firmwares so we need to read that
from the firmware image.
Also fix debug log for the patch address to print the address in hex.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to make it configurable by firmware IEs. Also determine if we need
to write or read the board address to the chip by checking if board address
is set or not.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Having separate defines, in a different file, makes it difficult to read
the actual values. As we are just setting named fields in a struct
the defines don't make any sense anymore.
There are no functional changes, only moving of constants.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds phy reset functionality to mdio-gpio driver. Now
mdio_gpio_platform_data has new member as function pointer which can be
filled at the bsp level for a callback from phy infrastructure. Also the
mdio-bitbang driver fills-in the reset function of mii_bus structure.
Without this patch the bsp level code has to takecare of the reseting
PHY's on the bus, which become bit hacky for every bsp and
phy-infrastructure is ignored aswell.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only update VERSION to reflect previous changes.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now works on Samsung Series 5 (chromebook)
Two fixes here:
o use 0x7F mask for phymode
o read phyid *AFTER* phy is powered up (via GPIOs)
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the phy isn't ready after reset...poll and pray it will be soon.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct value for rtl phy support.
(rtl phy are in AX88178 devices like NWU220G and USB2-ET1000).
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we hit the default case in the switch in if_spi_host_to_card() we'll leak
the memory we allocated for 'packet'. This patch resolves the leak by freeing
the allocated memory in that case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The generic powersaving code that determines after reception of a frame
whether the device should go back to sleep or whether is could stay
awake was calling rt2x00lib_config directly from RX tasklet context.
On a number of the devices this call can actually sleep, due to having
to confirm that the sleeping commands have been executed successfully.
Fix this by moving the call to rt2x00lib_config to a workqueue call.
This fixes bug https://bugzilla.redhat.com/show_bug.cgi?id=731672
Tested-by: Tomas Trnka <tomastrnka@gmx.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is reported to be an RT3070 based device.
Reported-by: Teika Kazura <teika@lavabit.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This message should be a debug message and not an error.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
This message should be a debug message and not a warning.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
