Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid link notification duplication
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Karim Hamiti <karim.hamiti@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIe connections should be expressed as GT/s (GigaTransfers per second)
instead of the current Gb/s (Gigabits per second). In addition, it is
incorrect because (due to PCIe gen 1 & 2 having a 20% overhead) the
actually data rate, when expressed in Gb/s, is only 80% of the rate of
GT/s.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce buffered read/writes which greatly improves performance on
parts with large EEPROMs.
Previously reading/writing a word requires taking/releasing of synchronization
semaphores which adds 10ms to each operation. The optimization is to
read/write in buffers, but make sure the semaphore is not held for >500ms
according to the datasheet.
Since we can't read the EEPROM page size ixgbe_detect_eeprom_page_size() is
used to discover the EEPROM size when needed and keeps the result in
word_page_size for the rest of the run time.
Use buffered reads for ethtool -e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
warning: symbol 'before' shadows an earlier one
Convert large macros to functions similar to e1000e.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correcting a simple typo with enabling software defined pins. I don't
believe this was causing any issues but this is how it was meant to be
implemented.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change remaining direct calls to function pointers.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device lies about supporting phys_id. Remove it and just
let the upper layer report not supported.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent commits have changed how EEPROM size is checked and if the size
word is misconfigured, the driver will fail to load. This patch adds a
check for invalid size word in the EEPROM and uses default size instead
for 82576 parts.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch sent by Stephen Hemminger.
This version incorporates the ethtool changes that Bruce Allan
submitted.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Evan Swanson <evan.swanson@intel.com>
In function 'e100_hw_init':
warning: 'err' may be used uninitialized in this function
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
stmmac.h uses struct platform_device and doesn't include
<linux/platform_device.h>. Whereas drivers/net/stmmac/stmmac.h includes it, but
doesn't directly use it. And so we get following compilation warning while using
this file:
warning: ‘struct platform_device’ declared inside parameter list
This patch includes <linux/platform_device.h> in linux/stmmac.h and removes it
from drivers/net/stmmac/stmmac.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
84c49d8c3e ("veth: remove unneeded
ifname code from veth_newlink()") caused regression on veth
creation. This patch reverts the original one.
Reported-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset loop check should check the MII_BMCR register value for
BMCR_RESET rather than for MII_BMCR (the register address, which also
happens to be zero).
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is supposed to enable WoL by default on adapters which support
that, but it fails to do so unless the adapter's
/sys/devices/.../power/wakeup file contains 'enabled' during the
initialization of the adapter. Fix that by making tg3 use
device_set_wakeup_enable() to enable wakeup automatically whenever
WoL should be enabled by default.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mwifiex_cmd_append_tsf_tlv(), two tsf_val TLVs should be
filled in the buffer and then sent to firmware.
The missing first TLV for tsf_val is added back in this patch.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB drivers don't support automatically waking up when in powersaving mode,
add a work object which will wakeup the device in time to receive the next beacon.
Based on that beacon, we either go back into powersaving mode, or we remain awake
to receive the buffered frames for our station.
Some part of the code, especially rt2x00lib_find_ie and rt2x00lib_rxdone_check_ps
are inspired on the code from carl9170.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use flag instead of re-reading the eeprom every time.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2800lib.c the rt2800_init_eeprom function the same eeprom
words were read multiple times, due to inefficient ordering of the
eeprom checks.
Reorder the checks so that each EEPROM word only has to be read once.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch
rt2x00: Optimize register access in rt2800pci
from Helmut Schaa missed one register call, namely
the rt2800_register_multiwrite which should be changed
to rt2x00pci_register_multiwrite.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add recycling functionality to rt2x00usb_register_read_async.
When the callback function returns true, resubmit the urb to
read the register again.
This optimizes the rt2800usb driver when multiple TX status reports
are pending in the register, because now we don't need to allocate
the rt2x00_async_read_data and urb structure each time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no TX status was available, the default timeout
of 20ms is a bit high. The frame is highly likely already
send out, so the TX status should be available within
only a few milliseconds.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By reading the "driver_state" debugfs value we get all the important
state information from the wl12xx driver. This helps testing and
debugging, particularly in situations where the driver seems "stuck".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP, the TX queues are not stopped when we start
recovery. mac80211 is notified only after the fact. When there is
pending TX, it will be queued even after the FW is down. This leads to
situations where the TX queues are stopped (because of the TX-watermark
mechanism), and are never woken up when we return from recovery.
Fix this by explicitly stopping the TX queues when before initiating
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This entry is useful for debugging the driver state machine during
recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When there's a change in the basic rates of the AP, reconfigure relevant
templates with the new rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the minimal rate configured in the basic rates set as the AP
broadcast and multicast rate. The minimal rate is used to ensure weak
links can still communicate.
When the basic rates contains at least one OFDM rate, configure all
unicast TX rates to OFDM only.
Unify rate configuration on initialization and on change notification
into a single function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When performing recovery, print the firmware version and program
counter (by reading the SCR_PAD4 register). The value of the firmware
program counter during assert can be useful for debugging.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We use a long timeout (2 seconds) when sending commands to the FW.
When a command times out, it means the FW is stuck, and we should
commence recovery.
This should make recovery times shorter as we'll recover on the first
timeout indication.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New AP-mode FWs filter external beacons by default. Disable this
filtering on start up so we can properly configure ERP protection.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the wiphy RTS and fragmentation thresholds for initializing the FW
when possible. This mitigates a bug where previously set values are
forgotten after interface down/up.
Add checks before settings these values to ensure they are valid. Use
default values when invalid thresholds are configured.
Update the default RTS threshold to the maximum value given by the
specification.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize AP specific BT coexitance parameters to default values and
enable them in AP mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is preferred to use the setter that to set queue_mapping directly.
This also helps backporting in compat-wireless.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When packets arrive with a RX descriptor indicating corruption, discard
them.
In general white-list the RX descriptor status to prevent rouge data
from being sent up.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Frames are considered pending when they reside in the driver TX queue or
already queued in the FW.
This notion of "pending" is appropriate for power save considerations in
STA mode, but not necessarily in other modes (for instance P2P-GO).
[Fixed a sparse warning about missing "static" in a function
declaration -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW can dynamically manage its internal TX & RX memory pools, moving
blocks from one pool to another when necessary. This can significantly
improve performance. Currently this feature is enabled only for 128x.
Enable dynamic memory for 127x as well. Other parameters in the memory
configuration structure may need to be fine tuned, as the optimal values
for these may change once dynamic memory is enabled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver stops sending TX packets when either there aren't enough
memory blocks, or it runs out of TX descriptors. The driver continues to
send packets to the FW only when more memory blocks are available.
The FW might free TX descriptors without freeing the corresponding
memory blocks, especially when dynamic memory is enabled. In cases where
memory blocks are not freed at all, the driver will keep waiting for
more memory blocks indefinitely.
Fix this by clearing the WL1271_FLAG_FW_TX_BUSY flag when there are
available TX descriptors.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 128x/AP firmware does not yet support dynamic memory. Temporarily,
the memory configuration for the 127x was used both for 127x/AP as well
as 128x/AP. Since the two chips don't have the same number of memory
blocks, TP was significantly degraded.
This hasn't been fine tuned yet, but using the base 128x numbers
(without dynamic memory) seems to yield much better results (around 30%
more). Additional fine tuning will be required in the future.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When configuring ACX_WAKE_UP_CONDITIONS (before entering psm), we
tell the firmware to wake up once in N DTIMs/beacons.
Allow control of this value via debugfs (for debugging purposes).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
