- Shorten include paths to machine specific headers.
- Remove fill_inbuf, not defined here.
- Return __dest as value from memcpy.
- Enable serial port hardware transmitter and receiver in serial_setup.
- Correct baudrate divisor calculation, changed from 4800 to 115200.
- Add support for Artpec-3 specific serial port setup.
- Initialize pinmux for the correct serial port.
- Fixes for NAND and NOR flash booting.
- Use assembler macros for common tasks (clocks, general io etc)
- Use (EtraxFS or Artpec-3) machine specific include for dram and hardware init.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use KBUILD_CFLAGS instead of CFLAGS.
- Remove raw_prink hack, use oops_in_progress instead.
- When ETRAX_WATCHDOG_NICE_DOGGY is set, loop in trap after oops dump
instead of rebooting.
- Break long lines to less than 80 chars.
- Fix whitespace errors.
- Remove unnecessary comments.
- Add config to use mtd0 as whole flash device.
- Fix whitespace errors.
- Remove braces around single statement ifs.
- Break long lines.
- Remove unnecessary CVS log.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
Removes a lot of cruft.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old and non-generic targets, use generic ones instead.
- Add sub-arch as mach-fs or mach-a3 for EtraxFS and Artpec-3 respectively.
- Add links to sub-arch directories, and erase before trying to create them.
- Include from sub-arch specific include directory "mach".
- Add files to be cleaned in CLEAN_FILES instead of as archclean target.
- Use default partition table when no partition is found (for initial tests)
- Add config ETRAX_AXISFLASHMAP_MTD0WHOLE to allow whole flash as mtd0.
- Add config for VCS simulator connection.
- Add i2c_write and i2c_read as functions.
- Use spinlocks for critical regions.
- Add config item to set I2C data and clock port.
- Put unneeded testcode inside #if 0.
- Remove CVS id tag.
- Remove CRISv32 common arbiter, dma, io and pinmux files,
they are now defined in machine dependent directories.
- Add cache and cacheflush files for working around cache problems
in CRISv32 chips.
- Collect extern declarations at top of file.
- Change raw_printk to printk, use oops_in_progress instead.
- Fix formatting and whitespace.
- Allow the watchdog to be disabled during oops.
- Only disallow oops if we're in_interrupt context (was in_atomic before)
- Use the generic oops_in_progress instead of the raw_printk hack.
- Fix whitespace/formatting.
- Remove CVS log entries.
- Add partition table struct to be used to parse partition table in flash.
- Add JFFS2 as a type, and add readoly flag.
- Improve some comments.
- Lindent has been run, fixing whitespace and formatting issues.
The header files describe the hardware registers available in both
these chips, note that most of this documentation is automatically
generated from the hardware implementation.
The two chips are somewhat different, and needs different handling.
Adds handing of the dma, dram initialization, hardware settings, io,
memory arbiter and pinmux
Also moves the dma, dram initialization and io from CRIS v32 common files.
- Remove some unneeded configs and add some new ones.
- Merge common config items to common file instead of duplicating them.
- Pull in standard Kconfig.preempt.
- Remove some unneeded Kconfigs for subsystems not (yet) available on CRIS
(md, scsi, ieee1394, i2o, isdn, telephony, media, pcmcia, pci)
- Rename CRISv32 config items which had different types from CRISv10.
(ETRAX_LED2G, ETRAX_LED2R, ETRAX_LED3G, ETRAX_LED3R, ETRAX_I2C_DATA_PORT,
ETRAX_I2C_CLK_PORT)
walk_memory_resource() verifies if there are holes in a given memory
range, by checking against /proc/iomem. On x86/ia64 system memory is
represented in /proc/iomem. On powerpc, we don't show system memory as
IO resource in /proc/iomem - instead it's maintained in
/proc/device-tree.
This provides a way for an architecture to provide its own
walk_memory_resource() function. On powerpc, the memory region is
small (16MB), contiguous and non-overlapping. So extra checking
against the device-tree is not needed.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Supply remove_memory() function for 64-bit powerpc. This is still
not quite complete as it needs to do some more arch-specific stuff,
which will be added in a later patch.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the cell IOMMU fixed mapping just printks that it's been setup,
which is not particularly useful. Much more interesting is the address
ranges for the different windows. This adds one line to dmesg on a blade.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we get a 64-bit dma mask we switch to the fixed ops and call
cell_dma_dev_setup(). If the driver then switches back to a 32-bit dma
mask for any reason we don't call cell_dma_dev_setup() again, which
has the potential to leave bogus data in dev->archdata.dma_data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order for the cell IOMMU fixed mapping to work we need "dma-ranges"
properties in the device tree. If there are none then there's no point
enabling the fixed mapping support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cell IOMMU fixed mapping support has a null pointer bug if you run
it on older firmwares that don't contain the "dma-ranges" properties.
Fix it and convert to using of_get_next_parent() while we're there.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Stop bits are only valid when the running bit is not set. Status bits
carry over from one invocation of spufs_run_spu() to another, so the
RUNNING bit gets added to the previous state of the register which may
have been a remote library call. In this case, it looks like another
library routine should be invoked, but the spe is actually running.
This fixes a problem with a testcase that exercises the scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't need to update the libassist statistic with the context in a
runnable state, so do it after spu_disable_spu().
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the kernel may fail to restart a SPE context which
has stopped and been swapped out.
This changes spu_backing_runcntl_write to emulate the real
SPU_Status register exactly. When the SPU Run Control register
is written with SPU_RunCntl[Run] set to '1', the physical SPU
automatically sets SPU_Status[R] and clears SPU_Status[CISHP].
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix various state_mutex leaks. The worst one was introduced by the
interrutible state_mutex conversion but there've been a few before
too. Notably spufs_wait now returns without the state_mutex held
when returning an error, which actually cleans up some code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that with the U3 northbridge, if the processor is in NAP
mode the whole time while waiting for an SMU command to complete,
then the SMU will fail. It could be related to the weird backward
mechanism the SMU uses to get to system memory via i2c to the
northbridge that doesn't operate properly when the said bridge is
in napping along with the CPU. That is on U3 at least, U4 doesn't
seem to be affected.
This didn't show before NO_HZ as the timer wakeup was enough to make
it work it seems, but that is no longer the case.
This fixes it by disabling NAP mode on those machines while
an SMU command is in flight.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the Ricoh RL5c476 chip: with this
the mmc adapter that needs this disabler (R5C843) can also be
handled correctly when it sits on a RL5c476.
Signed-off-by: Frank Seidel <fseidel@suse.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the AT91 MMC driver to use the generic GPIO calls instead of the
AT91-specific calls; and to request (and release) those GPIO signals.
That required updating the probe() fault cleanup codepaths. Now there
is a single sequence for freeing resources, in reverse order of their
allocation. Also that code uses use dev_*() for messaging, and has less
abuse of KERN_ERR.
Likewise with updating remove() cleanup. This had to free the GPIOs,
and while adding that code I noticed and fixed two other problems: it
was poking at a workqueue owned by the mmc core; and in one (rare)
case would try freeing an IRQ that it didn't allocate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some devices have several controllers; need add the index info to
device slot name host->slot_desc[]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
