If CONFIG_FRAME_WARN is small (1K) and CONFIG_NR_CPUS big
then a frame size warning is triggered during build.
Allocate the cpu mask dynamically to silence the warning.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Error code EAGAIN should be used when errors are temporary and next call
might succeeds.
When error code other than EAGAIN is returned, the caller (mlx4_ib_poll)
will assume all CQE in the same bunch are error too and will drop them all.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to return int if function always returns 0
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The cec-funcs.h header was missing support for these three vendor-specific messages:
CEC_MSG_VENDOR_COMMAND
CEC_MSG_VENDOR_COMMAND_WITH_ID
CEC_MSG_VENDOR_REMOTE_BUTTON_DOWN
Add wrappers for these messages.
I originally postponed adding these wrappers due to the fact that the argument is
just a byte array which cec-ctl couldn't handle at the time, and then I just forgot
to add them once the CEC framework was finalized.
It wasn't until an attempt to transmit a vendor specific command was made that I
realized that these wrappers were missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cec_get_edid_spa_location() function did not verify that the IEEE
identifier in the Vendor Specific Data Block matched the HDMI-LLC
identifier. This could result in the wrong VSDB block being returned.
For example, for HDMI 2.0 EDIDs there is also a HDMI Forum VSDB.
So check the IEEE identifier as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Support more error codes and fix a bug where MSGCODE_TRANSMIT_FAILED_LINE
was mapped to CEC_TX_STATUS_ARB_LOST, which is wrong.
Thanks to Pulse-Eight for providing me with the information needed
to handle this correctly (I hope).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't hardcode the signal free time to 3 bit periods, instead use
the value for the signal free time as passed in by the CEC framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This fixes this kbuild test robot error:
tree: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git master
head: 329f415291
commit: c1023ba74f [media] drivers/media/platform/Kconfig: fix VIDEO_MEDIATEK_VCODEC dependency
config: m32r-allyesconfig (attached as .config)
compiler: m32r-linux-gcc (GCC) 4.9.0
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
git checkout c1023ba74f
# save the attached .config to linux build tree
make.cross ARCH=m32r
All errors (new ones prefixed by >>):
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function 'vb2_dc_get_userptr':
>> >> drivers/media/v4l2-core/videobuf2-dma-contig.c:486:2: error: implicit declaration of function 'dma_get_cache_alignment' [-Werror=implicit-function-declaration]
unsigned long dma_align = dma_get_cache_alignment();
^
cc1: some warnings being treated as errors
This driver depends on HAS_DMA for dma_get_cache_alignment().
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most CEC adapters will still receive broadcast messages, even if no logical
addresses are claimed. But those messages should only be passed on for
monitoring purposes, but not for processing by either kernel or userspace
if userspace didn't call CEC_ADAP_S_LOG_ADDRS first.
So if adap->log_addrs.log_addr_mask is 0, then just return before passing
the received message on to the processing code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Up to 4 logical addresses can be claimed. Make sure that any
unclaimed logical addresses are set to CEC_LOG_ADDR_INVALID as
per the documentation.
Take special care in the unregistered case: when falling back to
unregistered num_log_addrs may be > 1, so mark those as invalid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently if none of the requested logical addresses can be claimed, the
framework will fall back to the Unregistered logical address.
Add a flag to enable this explicitly. By default it will just go back to
the unconfigured state.
Usually Unregistered is not something you want since the functionality is
very limited. Unless the application has support for this, it will fail
to work correctly. So require that the application explicitly requests
this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If an IRQ is setup using __setup_irq(), which is used by the
request_irq() family of functions, and we are using an SMP kernel then
the affinity of the IRQ will be set via setup_affinity() immediately
after the IRQ is enabled. This call to gic_set_affinity() will lead to
the interrupt being mapped to a VPE. However there are other ways to use
IRQs which don't cause affinity to be set, for example if it is used to
chain to another IRQ controller with irq_set_chained_handler_and_data().
The irq_set_chained_handler_and_data() code path will enable the IRQ,
but will not trigger a call to gic_set_affinity() and in this case
nothing will map the interrupt to a VPE, meaning that the interrupt is
never received.
Fix this by implementing the activate operation for the GIC device IRQ
domain, using gic_shared_irq_domain_map() to map the interrupt to the
correct pin of cpu 0.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_shared_irq_domain_map() is called from gic_irq_domain_alloc() where
the wrong chip has been set, and is then overwritten. Tidy this up by
setting the correct chip the first time, and setting the
handle_level_irq handler from gic_irq_domain_alloc() too.
gic_shared_irq_domain_map() is also called from gic_irq_domain_map(),
which now calls irq_set_chip_and_handler() to retain its previous
behaviour.
This patch prepares for a follow-on which will call
gic_shared_irq_domain_map() from a callback where the lock on the struct
irq_desc is held, which without this change would cause the call to
irq_set_chip_and_handler() to lead to a deadlock.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The documentation for the cec_event_state_change struct was incomplete.
This patch documents what happens in the corner cases.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A reply parameter is added to the cec_msg_record_on/off functions in
cec-funcs.h. The standard mandates that Record Status shall be replied
to Record On, and it may be replied to Record Off.
Signed-off-by: Johan Fjeldtvedt <jaffe1@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix typo where logical AND was used instead of bitwise AND.
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
- The global lock was used in cec_get_device when it should have
used the devnode lock.
- cec_put_device also took the global lock, but since the release
function takes that lock as well this could lead to a deadlock.
Just don't take the lock here since there is no reason for it.
- cec_devnode_register() should take the global lock when clearing
the bit in the global bitmap.
- In cec_devnode_unregister() place the devnode->(un)register tests
and assignments under the devnode lock as well: this has to be
in a critical block.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This lock will be used to protect more than just the fhs list.
So rename it to just 'lock'.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A station pointer can be passed to the driver on tx, before it has been
marked as associated. Since ath9k_sta_state was initializing the entry
too late, it resulted in some spurious crashes.
Fixes: df3c6eb34d ("ath9k: Use sta_state() callback")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Cherryview GPIO controller has 8 or 16 wires connected to the I/O-APIC
which can be used directly by the platform/BIOS or drivers. One such wire
is used as SCI (System Control Interrupt) which ACPI depends on to be able
to trigger GPEs (General Purpose Events).
The pinctrl driver itself uses another IRQ resource which is wire OR of all
the 8 (or 16) wires and follows what BIOS has programmed to the IntSel
register of each pin.
Currently the driver masks all interrupts at probe time and this prevents
these direct interrupts from working as expected. The reason for this is
that some early stage prototypes had some pins misconfigured causing lots
of spurious interrupts.
We fix this by leaving the interrupt mask untouched. This allows SCI and
other direct interrupts work properly. What comes to the possible spurious
interrupts we switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Reported-by: Yu C Chen <yu.c.chen@intel.com>
Reported-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A previous patch attempted to fix the pinmuxes for mfio 84 - 89, but it
omitted a change to pistachio_pin_group pistachio_groups, which results
in incorrect pll_lock signals being routed.
Apply the correct mux settings throughout the driver.
fixes: cefc03e599 ("pinctrl: Add Pistachio SoC pin control driver")
fixes: e9adb336d0 ("pinctrl: pistachio: fix mfio84-89 function description and pinmux.")
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: James Hartley <james.hartley@imgtec.com>
Reviewed-by: Sifan Naeem <Sifan.Naeem@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we're enabling a pipe, we'll need to modify the watermarks on all
active planes. Since those planes won't be added to the state on
their own, we need to add them ourselves.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-6-git-send-email-cpaul@redhat.com
(cherry picked from commit 05a76d3d6a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we write watermark values to the hardware, those values are stored
in dev_priv->wm.skl_hw. However with recent watermark changes, the
results structure we're copying from only contains valid watermark and
DDB values for the pipes that are actually changing; the values for
other pipes remain 0. Thus a blind copy of the entire skl_wm_values
structure will clobber the values for unchanged pipes...we need to be
more selective and only copy over the values for the changing pipes.
This mistake was hidden until recently due to another bug that caused us
to erroneously re-calculate watermarks for all active pipes rather than
changing pipes. Only when that bug was fixed was the impact of this bug
discovered (e.g., modesets failing with "Requested display configuration
exceeds system watermark limitations" messages and leaving watermarks
non-functional, even ones initiated by intel_fbdev_restore_mode).
Changes since v1:
- Add a function for copying a pipe's wm values
(skl_copy_wm_for_pipe()) so we can reuse this later
Fixes: 734fa01f3a ("drm/i915/gen9: Calculate watermarks during atomic 'check' (v2)")
Fixes: 9b61302274 ("drm/i915/gen9: Re-allocate DDB only for changed pipes")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-4-git-send-email-cpaul@redhat.com
(cherry picked from commit 2722efb90b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since the watermark calculations for Skylake are still broken, we're apt
to hitting underruns very easily under multi-monitor configurations.
While it would be lovely if this was fixed, it's not. Another problem
that's been coming from this however, is the mysterious issue of
underruns causing full system hangs. An easy way to reproduce this with
a skylake system:
- Get a laptop with a skylake GPU, and hook up two external monitors to
it
- Move the cursor from the built-in LCD to one of the external displays
as quickly as you can
- You'll get a few pipe underruns, and eventually the entire system will
just freeze.
After doing a lot of investigation and reading through the bspec, I
found the existence of the SAGV, which is responsible for adjusting the
system agent voltage and clock frequencies depending on how much power
we need. According to the bspec:
"The display engine access to system memory is blocked during the
adjustment time. SAGV defaults to enabled. Software must use the
GT-driver pcode mailbox to disable SAGV when the display engine is not
able to tolerate the blocking time."
The rest of the bspec goes on to explain that software can simply leave
the SAGV enabled, and disable it when we use interlaced pipes/have more
then one pipe active.
Sure enough, with this patchset the system hangs resulting from pipe
underruns on Skylake have completely vanished on my T460s. Additionally,
the bspec mentions turning off the SAGV with more then one pipe enabled
as a workaround for display underruns. While this patch doesn't entirely
fix that, it looks like it does improve the situation a little bit so
it's likely this is going to be required to make watermarks on Skylake
fully functional.
This will still need additional work in the future: we shouldn't be
enabling the SAGV if any of the currently enabled planes can't enable WM
levels that introduce latencies >= 30 µs.
Changes since v11:
- Add skl_can_enable_sagv()
- Make sure we don't enable SAGV when not all planes can enable
watermarks >= the SAGV engine block time. I was originally going to
save this for later, but I recently managed to run into a machine
that was having problems with a single pipe configuration + SAGV.
- Make comparisons to I915_SKL_SAGV_NOT_CONTROLLED explicit
- Change I915_SAGV_DYNAMIC_FREQ to I915_SAGV_ENABLE
- Move printks outside of mutexes
- Don't print error messages twice
Changes since v10:
- Apparently sandybridge_pcode_read actually writes values and reads
them back, despite it's misleading function name. This means we've
been doing this mostly wrong and have been writing garbage to the
SAGV control. Because of this, we no longer attempt to read the SAGV
status during initialization (since there are no helpers for this).
- mlankhorst noticed that this patch was breaking on some very early
pre-release Skylake machines, which apparently don't allow you to
disable the SAGV. To prevent machines from failing tests due to SAGV
errors, if the first time we try to control the SAGV results in the
mailbox indicating an invalid command, we just disable future attempts
to control the SAGV state by setting dev_priv->skl_sagv_status to
I915_SKL_SAGV_NOT_CONTROLLED and make a note of it in dmesg.
- Move mutex_unlock() a little higher in skl_enable_sagv(). This
doesn't actually fix anything, but lets us release the lock a little
sooner since we're finished with it.
Changes since v9:
- Only enable/disable sagv on Skylake
Changes since v8:
- Add intel_state->modeset guard to the conditional for
skl_enable_sagv()
Changes since v7:
- Remove GEN9_SAGV_LOW_FREQ, replace with GEN9_SAGV_IS_ENABLED (that's
all we use it for anyway)
- Use GEN9_SAGV_IS_ENABLED instead of 0x1 for clarification
- Fix a styling error that snuck past me
Changes since v6:
- Protect skl_enable_sagv() with intel_state->modeset conditional in
intel_atomic_commit_tail()
Changes since v5:
- Don't use is_power_of_2. Makes things confusing
- Don't use the old state to figure out whether or not to
enable/disable the sagv, use the new one
- Split the loop in skl_disable_sagv into it's own function
- Move skl_sagv_enable/disable() calls into intel_atomic_commit_tail()
Changes since v4:
- Use is_power_of_2 against active_crtcs to check whether we have > 1
pipe enabled
- Fix skl_sagv_get_hw_state(): (temp & 0x1) indicates disabled, 0x0
enabled
- Call skl_sagv_enable/disable() from pre/post-plane updates
Changes since v3:
- Use time_before() to compare timeout to jiffies
Changes since v2:
- Really apply minor style nitpicks to patch this time
Changes since v1:
- Added comments about this probably being one of the requirements to
fixing Skylake's watermark issues
- Minor style nitpicks from Matt Roper
- Disable these functions on Broxton, since it doesn't have an SAGV
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-3-git-send-email-cpaul@redhat.com
[mlankhorst: ENOSYS -> ENXIO, whitespace fixes]
(cherry picked from commit 656d1b89e5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In order to add proper support for the SAGV, we need to be able to know
what the cause of a failure to change the SAGV through the pcode mailbox
was. The reasoning for this is that some very early pre-release Skylake
machines don't actually allow you to control the SAGV on them, and
indicate an invalid mailbox command was sent.
This also might come in handy in the future for debugging.
Changes since v1:
- Add functions for interpreting gen6 mailbox error codes along with
gen7+ error codes, and actually interpret those codes properly
- Renamed patch to reflect new behavior
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-2-git-send-email-cpaul@redhat.com
[mlankhorst: -ENOSYS -> -ENXIO for checkpatch]
(cherry picked from commit 87660502f1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the recent patch
bc3d674 drm/i915: Allow userspace to request no-error-capture upon ...
the final version moved the flags and the associated #defines around
so they were adjacent; unfortunately, they ended up between a comment
and the thing (hw_id) to which the comment applies :(
So this patch reshuffles the comment and subject back together.
Also, as we're touching 'hw_id', let's change it from just 'unsigned'
to a fully-specified 'unsigned int', because some code checking tools
(including checkpatch) object to plain 'unsigned'.
Fixes: bc3d674462 ("drm/i915: Allow userspace to request no-error-capture...")
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1471616622-6919-1-git-send-email-david.s.gordon@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 0be81156b3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If userspace is asynchronously streaming into the batch or other
execobjects, we may not flush those writes along with a change in cache
domain (as there is no change). Therefore those writes may end up in
internal chipset buffers and not visible to the GPU upon execution. We
must issue a flush command or otherwise we encounter incoherency in the
batchbuffers and the GPU executing invalid commands (i.e. hanging) quite
regularly.
v2: Throw a paranoid wmb() into the general flush so that we remain
consistent with before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90841
Fixes: 1816f92363 ("drm/i915: Support creation of unbound wc user...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Tested-by: Matti Hämäläinen <ccr@tnsp.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818161718.27187-1-chris@chris-wilson.co.uk
(cherry picked from commit 600f436801)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It's possible to have a non-zero plane mask and still wind up with a
total data rate of zero. There are two cases where this can happen:
* planes are active (from the KMS point of view), but are
all fully clipped (positioned offscreen)
* the only active plane on a CRTC is the cursor (which is handled
independently and not counted into the general data rate computations
These are both valid display setups (although unusual), so we need to
drop the WARN().
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: kms_universal_planes.cursor-only-pipe-*
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466196140-16336-4-git-send-email-matthew.d.roper@intel.com
Cc: stable@vger.kernel.org #v4.7+
(cherry picked from commit 43aa7e8750)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_state->active_crtcs is usually only initialized when doing a
modeset. During our first atomic commit after boot, we're effectively
faking a modeset to sanitize the DDB/wm setup, so ensure that this field
gets initialized before use.
v2:
- Don't clobber active_crtcs if our first commit really is a modeset
(Maarten)
- Grab connection_mutex when faking a modeset during sanitization
(Maarten)
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466196140-16336-2-git-send-email-matthew.d.roper@intel.com
Cc: stable@vger.kernel.org #v4.7+
(cherry picked from commit 1b54a880b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The commit 02fc76f6a changed base of the sysfs attributes from device to card.
The "show" callbacks dereferenced wrong objects because of this.
Fixes: 02fc76f6a7 ('ALSA: line6: Create sysfs via snd_card_add_dev_attr()')
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there's an error, pcm is released in line6_pcm_acquire already.
Fixes: 247d95ee6d ('ALSA: line6: Handle error from line6_pcm_acquire()')
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without locking out CPU mask operations we might end up with an inconsistent
view of the cpumask in the function.
Fixes: 5e385a6ef3: "genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1470924405-25728-1-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Obviously we should free action here if irq_chip_pm_get failed.
Fixes: be45beb2df: "genirq: Add runtime power management support for IRQ chips"
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1471854112-13006-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- A critical fix for chained irqchip where we failed to configure
the cascade interrupt trigger
- A GIC fix for self-IPI in SMP-on-UP configurations
- A PM fix for GICv3
- A initialization fix the the GICv3 ITS, triggered by kexec
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vmKj
-----END PGP SIGNATURE-----
Merge tag 'irqchip-for-4.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull genirq/irqchip fixes for 4.8-rc4 from Marc Zygnier
- A critical fix for chained irqchip where we failed to configure
the cascade interrupt trigger
- A GIC fix for self-IPI in SMP-on-UP configurations
- A PM fix for GICv3
- A initialization fix the the GICv3 ITS, triggered by kexec
When usb gadget is set gadget serial function, it will be crash in below
situation.
It will clean the 'port->port_usb' pointer in gserial_disconnect() function
when usb link is inactive, but it will release lock for disabling the endpoints
in this function. Druing the lock release period, it maybe complete one request
to issue gs_write_complete()--->gs_start_tx() function, but the 'port->port_usb'
pointer had been set NULL, thus it will be crash in gs_start_tx() function.
This patch adds the 'port->port_usb' pointer checking in gs_start_tx() function
to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.
This switches to a "decrement variable and wait" timeout scheme.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't assign -EINVAL to a u16.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of error, the function usb_get_phy() returns ERR_PTR() and never
returns NULL. The NULL test in the return value check should be replaced
with IS_ERR().
Fixes: b5a2875605 ("usb: renesas_usbhs: Allow an OTG PHY driver to
provide VBUS")
Cc: <stable@vger.kernel.org> # v4.3+
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow for platforms that have a reset controller driver in place to bring
the USB IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
