Ensure that memory mappings created for operation regions
do not cross page boundaries. Crossing a page boundary
while mapping regions can cause warnings if the pages have different attributes.
Such regions are probably BIOS bugs, and this is the workaround.
http://bugzilla.kernel.org/show_bug.cgi?id=14445
[Kernel summit hacking hour]
Signed-off-by: Bob Moore <robert.moore@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When the ideal error range can't be reached, this will safely use
a most closed one. Clean up some dumb codes in DPLL function too.
This fixes DPLL clock issue against one monitor at 1680x1050@60hz.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Annote acpi_processor_add with cpuinit since it calls a cpuinit function
acpi_processor_power_init and fixes a section mismatch warning.
We were warned by the following warning:
LD drivers/acpi/processor.o
WARNING: drivers/acpi/processor.o(.text+0x1829): Section mismatch in
reference from the function acpi_processor_add() to the function
.cpuinit.text:acpi_processor_power_init()
The function acpi_processor_add() references
the function __cpuinit acpi_processor_power_init().
This is often because acpi_processor_add lacks a __cpuinit
annotation or the annotation of acpi_processor_power_init is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Miles Lane reported the following error:
2 locks held by cat/4179:
#0: (&p->lock){+.+.+.}, at: [<c10a3884>] seq_read+0x25/0x315
#1: (&dev_priv->mm.active_list_lock){+.+...}, at: [<c119a854>]
i915_batchbuffer_info+0x2b/0x124
Pid: 4179, comm: cat Not tainted 2.6.32-rc5-git1 #2
Call Trace:
[<c104874f>] ? __debug_show_held_locks+0x1e/0x20
[<c1023fb0>] __might_sleep+0xf0/0xf7
[<c101c393>] kmap+0x17/0x58
[<c119a8d6>] i915_batchbuffer_info+0xad/0x124
[<c10a39bf>] seq_read+0x160/0x315
[<c108fb8c>] ? rw_verify_area+0x98/0xbb
[<c10a385f>] ? seq_read+0x0/0x315
[<c1090331>] vfs_read+0x75/0xa9
[<c10903f9>] sys_read+0x3b/0x5d
[<c1002a8f>] sysenter_do_call+0x12/0x36
The fix is relatively simple, use the atomic variants of kmap() that
avoid the potential sleep.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: get_tss_base_addr() should return a gpa_t
KVM: x86: Catch potential overrun in MCE setup
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: invalidate target of rename
fuse: fix kunmap in fuse_ioctl_copy_user
fuse: prevent fuse_put_request on invalid pointer
* git://git.infradead.org/users/dwmw2/mtd-2.6.32:
mtd/maps: gpio-addr-flash: depend on GPIO arch support
mtd/maps: gpio-addr-flash: pull in linux/ headers rather than asm/
mtd: nand: fix htmldocs warnings
The current implementation of get_user_desc() sign extends the return
value because of integer promotion rules. For the most part, this
doesn't matter, because the top bit of base2 is usually 0. If, however,
that bit is 1, then the entire value will be 0xffff... which is
probably not what the caller intended.
This patch casts the entire thing to unsigned before returning, which
generates almost the same assembly as the current code but replaces the
final "cltq" (sign extend) with a "mov %eax %eax" (zero-extend). This
fixes booting certain guests under KVM.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NOTE:
1. Macro style is so strange.
2. The value 0xc0 is not match with KS8695 manual. It should be 0x0c.
Signed-off-by: zeal <zealcook@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: mask extended topology info in cpuid
xen/hvc: make sure console output is always emitted, with explicit polling
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix kthread_bind() by moving the body of kthread_bind() to sched.c
sched: Disable SD_PREFER_LOCAL at node level
sched: Fix boot crash by zalloc()ing most of the cpu masks
sched: Strengthen buddies and mitigate buddy induced latencies
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, fs: Fix x86 procfs stack information for threads on 64-bit
x86: Add reboot quirk for 3 series Mac mini
x86: Fix printk message typo in mtrr cleanup code
dma-debug: Fix compile warning with PAE enabled
x86/amd-iommu: Un__init function required on shutdown
x86/amd-iommu: Workaround for erratum 63
* 'for-linus' of git://www.linux-m32r.org/git/takata/linux-2.6_dev:
m32r: Should index be positive?
m32r: bzip2/lzma kernel compression support
m32r: add NOTES to vmlinux.lds.S to remove .note.gnu.build-id section
arch/m32r: Use DIV_ROUND_CLOSEST
Not a single line of actual code in the function was really
fundamentally correct.
Problems ranged from lack of proper range checking, to removing the last
character written (which admittedly is usually '\n'), to not accepting
hex numbers even though the 'show' routine would show the data in that
format.
This tries to do better.
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-and-acked-by: Jack Steiner <steiner@sgi.com>
Cc: stable@kernel.org
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Michael Gilbert <michael.s.gilbert@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function hp_bseries_system() is always used, outside of
CONFIG_ boundaries/controls, so move it.
sound/pci/hda/patch_sigmatel.c:5458: error: implicit declaration of function 'hp_bseries_system'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the ACPI methods return an error code, we must return -EINVAL to userspace
to flag the error. Right now we pass the (positive) number right through,
which causes echo to keep writing bogus values.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
u-boot partition size should be 0x80000 (512 KB), not 0x8000 (32 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.
This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevent NULL dereference if kmalloc() fails. Also clean up if
of_mdiobus_register() returns an error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e. Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board. This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.
With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RealView PBX board has two 512MB blocks of memory - one at
0x70000000 (with 256MB mirror at 0) and another at 0x20000000. Only the
block at 0x70000000 (or the mirror at 0) may be used for DMA (e.g.
framebuffer). This patch adds the sparsemem definitions to allow the use
of all the memory split as follows:
256MB @ 0x00000000 (ZONE_DMA)
512MB @ 0x20000000 (ZONE_NORMAL)
256MB @ 0x80000000 (ZONE_NORMAL)
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The platsmp.c file defines the REALVIEW_SYS_FLAGS* macros which are
already present in platform.h. Just use the latter.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a realview_fixup() function called during booting to set
up the memory banks. This way there is no need to pass a "mem=" argument
on the kernel command line.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If Linux is running in non-secure mode, this register may have been
already initialised and writing to the control register not allowed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Commit
3d1285b (move virtnet_remove to .devexit.text)
introduced the first reference to __devexit in struct virtio_driver
virtio_net which upset modpost ("Section mismatch in reference from the
variable virtio_net to the function .devexit.text:virtnet_remove()").
Fix this by renaming virtio_net to virtio_net_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Blame-taken-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to parse the option of a SYN packet that we have
no route entry for should just use global wide defaults
for route entry options.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Tested-by: Valdis.Kletnieks@vt.edu
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling IPv4 specific inet_csk_route_req in tcp_check_req
is a bad idea and crashes machine on IPv6 connections, as reported
by Valdis Kletnieks
Also, all we are really interested in is the timestamp
option in the header, so calling tcp_parse_options()
with the "estab" set to false flag is an overkill as
it tries to parse half a dozen other TCP options.
We know whether timestamp should be enabled or not
using data from request_sock.
Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Tested-by: Valdis.Kletnieks@vt.edu
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: https://bugs.launchpad.net/bugs/474972
This Sony model needs External Amplifier muted for audible playback, so
make sure we set the inv_eapd quirk.
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch f598282f51 exposed a problem in
powerpc MSI-X functionality, making network interfaces such as ixgbe
and cxgb3 stop to work when MSI-X is enabled. RX interrupts were not
being generated.
The problem was caused because MSI irq was not being effectively
unmasked after device initialization.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Doing so causes xtime to be negative which crashes the timekeeping
code in funny ways when doing suspend/resume
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add suspend/resume capability to TI DaVinci EMAC driver.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed by Stephen Rothwell, commit c6d14c84 added a warning :
net/ipv4/devinet.c: In function 'inet_select_addr':
net/ipv4/devinet.c:902: warning: label 'out' defined but not used
delete unused 'out' label and do some cleanups as well
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I inadvertently left that debug code enabled, causing the number of
contexts to be clamped to 31 which is going to slow things down on
4xx and just plain breaks 8xx
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187
USB stick, or unloading the driver rtl8187 using rmmod will cause a
kernel oops. There are at least two forms of the failure, (1) BUG:
Scheduling while atomic, and (2) a fatal kernel page fault. This
problem is reported in Bugzilla #14539.
This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2,
thus it is technically a regression; however, bisection did not locate
any faulty patch. The fix was found by comparing the faulty code in
rtl8187 with p54usb. My interpretation is that the handling of work
queues in mac80211 changed enough to the LEDs to be unregistered
before tasks on the work queues are cancelled. Previously, these
actions could be done in either order.
(Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the
code is the same in 2.6.31, so this may be a candidate for 2.6.31.x.
-- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Rick Farina <sidhayn@gmail.com>
Tested-by: Rick Farina <sidhayn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX is handled in a workqueue therefore allocating for GFP_ATOMIC
is overkill and not required.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The internal scan request mac80211 uses to
scan for IBSS networks was set up to contain
no channels at all because n_channels wasn't
set after setting up the channels array. Fix
this to properly scan for networks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, in IBSS mode, a single creator would go into
a loop trying to merge/scan. This happens because the IBSS timer is
rearmed on finishing a scan and the subsequent
timer invocation requests another scan immediately.
This patch fixes this issue by checking if we have just completed
a scan run trying to merge with other IBSS networks.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since struct hw_key_entry is 32-bytes large and is smaller than
CSR cache size (which is 64-bytes large) we can use the standard
rt2x00usb_register_multiwrite() helper to set key entries.
This cleanup is a part of preparations for later code unification.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
