Send the EAPOL and management frames in the same AC_VO queue. The issue
happens when the AP supports QOS, the management frames are sent to AC_VO
queue and EAP frame goes to AC_BE queue. Even though the EAP frame is
queued before the DEAUTH management frame, as they are queued on different
h/w queues, order of delivery between these frames cannot be controlled.
This fixes the connection failure seen in P2P case.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following compile warnings:
fs/nfs/direct.c: In function 'nfs_direct_read_schedule_segment':
fs/nfs/direct.c:325:11: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c:325:11: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c:325:11: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c:352:27: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c: In function 'nfs_direct_write_schedule_segment':
fs/nfs/direct.c:622:11: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c:622:11: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c:622:11: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
fs/nfs/direct.c:650:27: warning: comparison of distinct pointer types
lacks a cast [enabled by default]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
When creating 64 bit integer controls make sure the max and step
values are 0 (as 64 bit controls do not have ranges).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver now complies with the v4l2-compliance tests and uses the v4l2
frameworks correctly.
It has been tested with the radio-keene FM transmitter as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable Bus Master bit on the device in pci_device_shutdown() to ensure PCI
devices do not continue to DMA data after shutdown. This can cause memory
corruption in case of a kexec where the current kernel shuts down and
transfers control to a new kernel while a PCI device continues to DMA to
memory that does not belong to it any more in the new kernel.
I have tested this code on two laptops, two workstations and a 16-socket
server. kexec worked correctly on all of them.
Signed-off-by: Khalid Aziz <khalid.aziz@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 384ebe1c28, "gpio/omap: Add DT
support to GPIO driver", introduced dynamic IRQ numbering of OMAP GPIO
interrupts, breaking all IH_GPIO_BASE based IRQ number calculations.
This issue was corrected in the OMAP GPIO driver and the related header
file with commit 25db711df3, "gpio/omap:
Fix IRQ handling for SPARSE_IRQ".
However, the Amstrad Delta FIQ handler, which replaces the gpio-omap
driver in serving GPIO interrupts on this board, still uses that
outdated method. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It appears some networks play bad games with the two bits reserved for
ECN. This can trigger false congestion notifications and very slow
transferts.
Since RFC 3168 (6.1.1) forbids SYN packets to carry CT bits, we can
disable TCP ECN negociation if it happens we receive mangled CT bits in
the SYN packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Perry Lorier <perryl@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Wilmer van der Gaast <wilmer@google.com>
Cc: Ankur Jain <jankur@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Dave Täht <dave.taht@bufferbloat.net>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is just no point mapping up to 512MB for a serial port.
Using a single 1MB entry is way sufficient for all users.
This will create less interference for the following debugging patch.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With multiple cards is hard to figure out which port caused trouble
int the layer2 routines (e.g. got a timeout).
Now we have the informations in the log output.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer3 and the activation delay timer need to be independent.
If timer3 fires do not reqest power up we have to send only INFO 0.
Now layer1 pass TBR3 again.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certification test it is very useful to change the layer1
timer3 value on runtime.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be full preemptiv safe, we cannot handle a L2 timeout in the timer
context itself, we should do all actions via the D-channel thread.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some configs it was still not possible to unload the driver,
because the module use count was srewed up.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MMCI and PL022 SPI drivers sure need their platform data to
work on the Versatile as well. (This does not fix the auxdata for
MMCI instance mmc1 on the Versatile PB though.)
Cc: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This does two things to the FPGA IRQ controller in the versatile
family:
- Convert to MULTI_IRQ_HANDLER so we can drop the entry macro
from the Integrator. The C IRQ handler was inspired from
arch/arm/common/vic.c, recent bug discovered in this handler was
accounted for.
- Convert to using IRQ domains so we can get rid of the NO_IRQ
mess and proceed with device tree and such stuff.
As part of the exercise, bump all the low IRQ numbers on the
Integrator PIC to start from 1 rather than 0, since IRQ 0 is
now NO_IRQ. The Linux IRQ numbers are thus entirely decoupled
from the hardware IRQ numbers in this controller.
I was unable to split this patch. The main reason is the half-done
conversion to device tree in Versatile.
Tested on Integrator/AP and Integrator/CP.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tei manager reports current layer 1 state on creation.
On state change it reports it to the socket interface.
Signed-off-by: Andreas Eversberg <andreas@eversberg.eu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"Some minor fixes from Intel and a radeon fix.
I have the nouveau fix for the i2c regression queued for next week,
its mostly a revert and seems to work on the system it was originally
introduced for thanks to some i2c core changes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: clarify and extend wb setup on APUs and NI+ asics
drm/i915: enable dip before writing data on gen4
fixing dmi match for hp t5745 and hp st5747 thin client
drm/i915: Only enable IPS polling for gen5
drm/i915: Do not read non-existent DPLL registers on PCH hardware
This fixes a regression that was introduced in the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=8qhg
-----END PGP SIGNATURE-----
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md
Pull one small fix for md/bitmaps from NeilBrown:
"This fixes a regression that was introduced in the merge window."
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md/bitmap: fix calculation of 'chunks' - missing shift.
Currently if we cannot decide the size of the event, we guess next
event possition by:
"... check alignment, and increment a single u64 in the hope
to catch on again 'soon'"
This usually ends up with segfault or endless loop. It's better
to admit the failure right away, then pretend nothing happened.
It makes the life easier ;)
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20120416184251.GA11503@m.brq.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jana Saout confirmed that this fixes the page faults he saw.
His problem was triggered by ocfs2 and autofs symlink lookups, where the
symlink allocation was at the end of a page. But the deeper reason
seems to be the use of Xen-PV, which is what then causes him to have all
these unmapped pages, which is what then makes it a problem when the
unaligned word-at-a-time code fetches data past the end of a page.
* fix-unmapped-word-at-a-time:
vfs: make word-at-a-time accesses handle a non-existing page
Now there are irqdomains in place for Snowball, we can request GPIO
IRQs directly by their binding. This replaces the previous method
of hard-coding the hwirq using u32 values in the DT.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This provides full documentation detailing each compulsory,
optional and device (variant) specific properties available
for use within the MMCI Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide a means to collect attributes specific to ST-Ericsson's ux500
variant series. This patch registers itself as the AMBA driver to be
called during the probe process. Once all attributes and ux500 specifics
are are collected the normal mmci core probe is called.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This cleans up the mode setting code when creating inodes. The
SGID bit was being reset by setattr_copy() when the user creating a
subdirectory was not in the owning group. When ACLs are in use this
SGID bit should have been propagated if the ACL allows creation of
a subdirectory. GFS2's behaviour now matches that of the other ACL
supporting filesystems in this regard.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
If CONFIG_KPROBES is not set, then linux/kprobes.h will not include
asm/kprobes.h needed by x86/ftrace.c for the BREAKPOINT macro.
The x86/ftrace.c file should just include asm/kprobes.h as it does not
need the rest of kprobes.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Missing handler for freeing requested IRQ added.
Moreover clk_ calls has been reorganized.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit adjust the s3c-hsotg to new clock API.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code removes the S3C_ prefix from s3c-hsotg driver. This change
provides more architecture independent code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add release function to prevent kernel warning.
Kfree is performed when all references are gone.
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The our_hsotg global pointer to hsotg USB device state is removed.
It has been replaced with to_hsotg(gadget) function.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Refactor all comments to comply with kernel codding style.
Moreover doxygen descriptions have been added for selected functions.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace of deprecated start and stop callbacks with a udc_start and
udc_stop ones.
Now the bind from composite driver is NOT called explicitly, so more
work needs to be done at s3c_udc_probe. Especially enabling SoC clocks
and power for runtime determination of EP number.
After probing, those sources are disabled and enabled again at udc_start
and pullup afterwards.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit adds support for determining of EPs number during run time.
Configuration is read from a HW configuration register in a specially
created s3c_hsotg_hw_cfg function.
Moreover it was necessary to defer at probe allocation of the
struct s3c_hsotg_ep instances until number of endpoints is known.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code allows Samsung SoC's to recover its state when
device is disconnected and connected during transfer.
It is necessary, in such a scenario, to reinitialize the USB core
to assure correct initial state of the driver.
This operation is needed since the disconnect interrupt is only
available at HOST mode, which is not supported by this driver.
A simple mechanism with jiffies has been used to perform core reset
only once.
Tested with:
- DFU gadget (various size of the sent data - also packet = MPS)
- Ethernet gadget (CDC and RNDIS)
- Multi Function Gadget (g_multi)
HW:
- Samsung's C210 Universal rev.0
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The s3c_hsotg_disconnect_irq function has been renamed to
reflect, that it can be used not only during the host
disconnect irq.
The s3c_hsotg_disconnect shall be used as a fall back for
scenario when USB cable is unplugged and plugged to the
device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB Disconnect Interrupt handler, according to specification,
is only working at HOST mode.
Samsung SoCs (e.g. Exynos4) are working at device mode, so
this interrupt is never caught.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The s3c_hsotg_core_init function has been added to exclude
code responsible for Samsung's SoCs USB core initialization.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit targets following scenarios for IN requests:
1. HOST requests e.g. 256B (which is a multiple of MPS = 64B).
Then NO ZLP shall be sent, since host expects exact number of bytes.
2. HOST requested 4096B, but our data for sending is 256B. In this
situation ZLP shall be send to tell HOST that no more data is available
and it shall not wait for more data. This prevents HOST from hanging.
Tested with:
- DFU gadget (various size of the sent data - also packet = MPS)
- Ethernet gadget (CDC and RNDIS)
- Multi Function Gadget (g_multi)
HW:
- Samsung's C210 Universal rev.0
- Samsung's C110 GONI
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For SETUP stage of USB control transmission, the NAK shall NOT be
CLEAR.
The SNAK/CNAK control is crucial for this type of driver,
since data arrives to earlier defined requests.
Tested with:
- DFU gadget (various size of the sent data - also packet = MPS)
- Ethernet gadget (CDC and RNDIS)
- Multi Function Gadget (g_multi)
HW:
- Samsung's C210 Universal rev.0
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit adds support for supply voltage management for s3c-hsotg IP
block. For that purpose a convenient regulator_bulk_* functions have been
used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Wrappers for PHY methods have been added for readability and reduction
of code repetition.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two functions - namely: s3c_hsotg_gate and s3c_hsotg_otgreset are platform
dependent and therefore removed from Samsung's generic s3c-hsotg code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This code removes platform dependency from s3c-hsotg driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
functionfs was leaking request objects created by autoconfig.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add two isochronous endpoints to the gadget zero source/sink
function. They are enabled by selecting alternate interface 1, so
by default they are not enabled. Module parameters for setting all
the isoc endpoint characteristics are also provided.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The original code works fine, but Sparse complains because it isn't
annotated properly.
drivers/usb/gadget/composite.c:793:26: warning: incorrect type in assignment (different base types)
drivers/usb/gadget/composite.c:793:26: expected unsigned short [unsigned] [usertype] language
devel/drivers/usb/gadget/composite.c:793:26: got restricted __le16 [usertype] <noident>
devel/drivers/usb/gadget/composite.c:795:29: warning: restricted __le16 degrades to integer
drivers/usb/gadget/composite.c:798:24: warning: incorrect type in assignment (different base types)
drivers/usb/gadget/composite.c:798:24: expected restricted __le16 [usertype] <noident>
devel/drivers/usb/gadget/composite.c:798:24: got unsigned short [unsigned] [usertype] language
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The previous code always set to USB_DEVICE_SELF_POWERED in GET_STATUS.
So, this patch adds set_selfpowered().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
