This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This removes CONFIG_PCI_LEGACY (which is not needed) and consequently
several compiler warnings.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
KVM host support was recently enabled in ppc44x_defconfig, but since then the
config option was renamed. Update ppc44x_defconfig to match.
Also, KVM guests aren't very interesting without networking, so enable
CONFIG_TUN and CONFIG_BRIDGE.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Impact: pack struct thread_info more tightly
Change x86_64's thread_info 'flags' field back to __u32.
This was changed to 'unsigned long' when the thread_info*.h
for i386 and x86_64 were merged. Change it back. We can
do this as only 27 bits of 'flags' are actually used.
This change actually packs down thread_info by 64 bits:
32 bits are saved by the smaller flags, and 32 bits are
saved by the following 'mm_segment_t field' becoming
naturally 64-bit aligned.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
final close of ->bdev should match the initial open, i.e.
get FMODE_READ | FMODE_NDELAY; FMODE_READ|FMODE_WRITE has
been a braino.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make sure all FMODE_ constants are documents, and ensure a coherent
style for the already existing comments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Update FMODE_NDELAY before each ioctl call so that we can kill the
magic FMODE_NDELAY_NOW. It would be even better to do this directly
in setfl(), but for that we'd need to have FMODE_NDELAY for all files,
not just block special files.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The way the bd_claim for the FMODE_EXCL case is implemented is rather
confusing. Clean it up to the most logical style.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 33c2dca495 (trim file propagation
in block/compat_ioctl.c) removed the handling of some ioctls from
compat_blkdev_driver_ioctl. That caused them to be rejected as unknown
by the compat layer.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
it had been put there to mark the call of blkdev_put() that
needed proper argument propagated to it; later patch in the
same series had done just that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 0c65f459ce intended to fix truncation issues with fls() on
ARMv5+ by renaming it to __fls() and wrapping it into a C function.
However that didn't take into account the fact that __fls() already
already had different semantics in the kernel.
Let's move the __fls() code into fls() function directly, and redefine
__fls() with the appropriate semantics. While at it, bring a generic
__fls() definition for pre ARMv5 too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Handle the TRACE_PRINT entries from the function grapg tracer
and output them as a C comment just below the function that called
it, as if it was a comment inside this function.
Example with an ftrace_printk inside might_sleep() function:
void __might_sleep(char *file, int line)
{
static unsigned long prev_jiffy; /* ratelimiting */
ftrace_printk("Hi I'm a comment in might_sleep() :-)");
A chunk of a resulting trace:
0) | _reiserfs_free_block() {
0) | reiserfs_read_bitmap_block() {
0) | __bread() {
0) | __getblk() {
0) | __find_get_block() {
0) 0.698 us | mark_page_accessed();
0) 2.267 us | }
0) | __might_sleep() {
0) | /* Hi I'm a comment in might_sleep() :-) */
0) 1.321 us | }
0) 5.872 us | }
0) 7.313 us | }
0) 8.718 us | }
And this patch brings two minor fixes:
- The newline after a switch-out task has disappeared
- The "|" sign just before the cpu number on task-switch has been deleted.
0) 0.616 us | pick_next_task_rt();
0) 1.457 us | _spin_trylock();
0) 0.653 us | _spin_unlock();
0) 0.728 us | _spin_trylock();
0) 0.631 us | _spin_unlock();
0) 0.729 us | native_load_sp0();
0) 0.593 us | native_load_tls();
------------------------------------------
0) cat-2834 => migrati-3
------------------------------------------
0) | finish_task_switch() {
0) 0.841 us | _spin_unlock_irq();
0) 0.616 us | post_schedule_rt();
0) 3.882 us | }
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix a bug in function filter setting
when writing function to set_graph_function, we should check whether it
has existed in set_graph_function to avoid duplicating.
Signed-off-by: Liming Wang <liming.wang@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: new feature
This patch lets the swapper tasks of all CPUS be filtered by the
set_ftrace_pid file.
If '0' is echoed into this file, then all the idle tasks (aka swapper)
is flagged to be traced. This affects all CPU idle tasks.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up, extend PID filtering to PID namespaces
Eric Biederman suggested using the struct pid for filtering on
pids in the kernel. This patch is based off of a demonstration
of an implementation that Eric sent me in an email.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: macro side-effects fix
This patch adds parenthesis around 'pid' in the do_each_pid_task
macro to allow callers to pass in more complex parameters.
e.g. do_each_pid_task(*pid, type, task)
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: New feature
This patch makes the changes to set_ftrace_pid apply to the function
graph tracer.
# echo $$ > /debugfs/tracing/set_ftrace_pid
# echo function_graph > /debugfs/tracing/current_tracer
Will cause only the current task to be traced. Note, the trace flags are
also inherited by child processes, so the children of the shell
will also be traced.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
Use the new task struct trace flags to determine if a process should be
traced or not.
Note: this moves the searching of the pid to the slow path of setting
the pid field. This needs to be converted to the pid name space.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds the file:
/debugfs/tracing/set_graph_function
which can be used along with the function graph tracer.
When this file is empty, the function graph tracer will act as
usual. When the file has a function in it, the function graph
tracer will only trace that function.
For example:
# echo blk_unplug > /debugfs/tracing/set_graph_function
# cat /debugfs/tracing/trace
[...]
------------------------------------------
| 2) make-19003 => kjournald-2219
------------------------------------------
2) | blk_unplug() {
2) | dm_unplug_all() {
2) | dm_get_table() {
2) 1.381 us | _read_lock();
2) 0.911 us | dm_table_get();
2) 1. 76 us | _read_unlock();
2) + 12.912 us | }
2) | dm_table_unplug_all() {
2) | blk_unplug() {
2) 0.778 us | generic_unplug_device();
2) 2.409 us | }
2) 5.992 us | }
2) 0.813 us | dm_table_put();
2) + 29. 90 us | }
2) + 34.532 us | }
You can add up to 32 functions into this file. Currently we limit it
to 32, but this may change with later improvements.
To add another function, use the append '>>':
# echo sys_read >> /debugfs/tracing/set_graph_function
# cat /debugfs/tracing/set_graph_function
blk_unplug
sys_read
Using the '>' will clear out the function and write anew:
# echo sys_write > /debug/tracing/set_graph_function
# cat /debug/tracing/set_graph_function
sys_write
Note, if you have function graph running while doing this, the small
time between clearing it and updating it will cause the graph to
record all functions. This should not be an issue because after
it sets the filter, only those functions will be recorded from then on.
If you need to only record a particular function then set this
file first before starting the function graph tracer. In the future
this side effect may be corrected.
The set_graph_function file is similar to the set_ftrace_filter but
it does not take wild cards nor does it allow for more than one
function to be set with a single write. There is no technical reason why
this is the case, I just do not have the time yet to implement that.
Note, dynamic ftrace must be enabled for this to appear because it
uses the dynamic ftrace records to match the name to the mcount
call sites.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix time warp bug
Alex Shi, along with Yanmin Zhang have been noticing occasional time
inconsistencies recently. Through their great diagnosis, they found that
the xtime_nsec value used in update_wall_time was occasionally going
negative. After looking through the code for awhile, I realized we have
the possibility for an underflow when three conditions are met in
update_wall_time():
1) We have accumulated a second's worth of nanoseconds, so we
incremented xtime.tv_sec and appropriately decrement xtime_nsec.
(This doesn't cause xtime_nsec to go negative, but it can cause it
to be small).
2) The remaining offset value is large, but just slightly less then
cycle_interval.
3) clocksource_adjust() is speeding up the clock, causing a
corrective amount (compensating for the increase in the multiplier
being multiplied against the unaccumulated offset value) to be
subtracted from xtime_nsec.
This can cause xtime_nsec to underflow.
Unfortunately, since we notify the NTP subsystem via second_overflow()
whenever we accumulate a full second, and this effects the error
accumulation that has already occured, we cannot simply revert the
accumulated second from xtime nor move the second accumulation to after
the clocksource_adjust call without a change in behavior.
This leaves us with (at least) two options:
1) Simply return from clocksource_adjust() without making a change if we
notice the adjustment would cause xtime_nsec to go negative.
This would work, but I'm concerned that if a large adjustment was needed
(due to the error being large), it may be possible to get stuck with an
ever increasing error that becomes too large to correct (since it may
always force xtime_nsec negative). This may just be paranoia on my part.
2) Catch xtime_nsec if it is negative, then add back the amount its
negative to both xtime_nsec and the error.
This second method is consistent with how we've handled earlier rounding
issues, and also has the benefit that the error being added is always in
the oposite direction also always equal or smaller then the correction
being applied. So the risk of a corner case where things get out of
control is lessened.
This patch fixes bug 11970, as tested by Yanmin Zhang
http://bugzilla.kernel.org/show_bug.cgi?id=11970
Reported-by: alex.shi@intel.com
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Tested-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ISA support in smc91x is incomplete. I doubt there're any smc91x isa card.
This driver is greatly used on arm pxa platforms. Hence we remove the
isa stuff from smc91x driver.
Signed-off-by: Luotao Fu <lfu@pengutronix.de>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, iproute2 fails to show multicast forwarding unresolved cache
entries while scanning /proc/net/ip_mr_cache.
Indeed, it expects to see -1 in 'Iif' column to identify unresolved
entries but the kernel outputs 65535. It's a signed/unsigned issue:
'Iif', the source interface, is retrieved from member mfc_parent in
struct mfc_cache. mfc_parent is a vifi_t: unsigned short, but is
displayed in ipmr_mfc_seq_show() as "%-3d", signed integer.
In unresolevd entries, the 65535 value (0xFFFF) comes from this define:
#define ALL_VIFS ((vifi_t)(-1))
That may explains why the guy who added support for this in iproute2
thought a -1 should be expected.
I don't know if this must be fixed in kernel or in iproute2. Who is
right? What is the correct API? How was it designed originally?
I let you decide if it should goes in the kernel or be fixed in iproute2.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/ip_mr_cache and /proc/net/ip6_mr_cache displays garbage when
showing unresolved mfc_cache entries.
[root@qemu tests]# cat /proc/net/ip_mr_cache
Group Origin Iif Pkts Bytes Wrong Oifs
014C00EF 010014AC 1 10 10050 0 2:1 3:1
024C00EF 010014AC 65535 514 2 -559067475
The first line is correct. It is a resolved cache entry, 10 packets used it...
The second line represents an unresolved entry, and the columns Pkts(4th),
Bytes(5th) and Wrong(6th) just show garbage.
In struct mfc_cache, there's an union to store data for resolved and
unresolved cases. And what ipmr_mfc_seq_show() is printing in these
columns for the unresolved entries is some bytes from mfc_cache.mfc_un.res.
Bad.
(eg. In our case -559067475 is in fact 0xdead4ead which is the spinlock
magic from mfc_cache.mfc_un.unres.unresolved.lock.magic).
This patch replaces the garbage data written in these columns for the
unresolved entries by '0' (zeros) which is more correct.
This change doesn't break the ABI.
Also, mfc->mfc_un.res.pkt, mfc->mfc_un.res.bytes, mfc->mfc_un.res.wrong_if
are unsigned long.
It applies on top of net-next-2.6.
The patch for net-2.6 is slightly different because of the NIP6_FMT to
%pI6 conversion that was made in the seq_printf.
Changelog:
==========
V2:
* Instead of breaking the ABI by suppressing the columns that have no
meaning for unresolved entries, fill them with 0 values.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
-m486, -O6 are partircularly amusing.
Remove some other useless lines near as well.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock used in the netx-eth driver was never properly initialized.
This was noticed using CONFIG_DEBUG_SPINLOCK=y
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
We lack compat ioctl support through most of the ATM code. This patch
deals with most of it, and I can now at least use BR2684 and PPPoATM
with 32-bit userspace.
I haven't added a .compat_ioctl method to struct atm_ioctl, because
AFAICT none of the current users need any conversion -- so we can just
call the ->ioctl() method in every case. I looked at br2684, clip, lec,
mpc, pppoatm and atmtcp.
In svc_compat_ioctl() the only mangling which is needed is to change
COMPAT_ATM_ADDPARTY to ATM_ADDPARTY. Although it's defined as
_IOW('a', ATMIOC_SPECIAL+4,struct atm_iobuf)
it doesn't actually _take_ a struct atm_iobuf as an argument -- it takes
a struct sockaddr_atmsvc, which _is_ the same between 32-bit and 64-bit
code, so doesn't need conversion.
Almost all of vcc_ioctl() would have been identical, so I converted that
into a core do_vcc_ioctl() function with an 'int compat' argument.
I've done the same with atm_dev_ioctl(), where there _are_ a few
differences, but still it's relatively contained and there would
otherwise have been a lot of duplication.
I haven't done any of the actual device-specific ioctls, although I've
added a compat_ioctl method to struct atmdev_ops.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348eef
"[NET]: Make NAPI polling independent of struct net_device objects."
made NAPI polling to be independent of net_device.
So e1000_adapter->polling_netdev is no longer used.
Kill it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems the ixgbe's code was copied from e1000.
The comment talks about something not exist.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I should have noticed this earlier... :-) The previous solution
to URG+GSO/TSO will cause SACK block tcp_fragment to do zig-zig
patterns, or even worse, a steep downward slope into packet
counting because each skb pcount would be truncated to pcount
of 2 and then the following fragments of the later portion would
restore the window again.
Basically this reverts "tcp: Do not use TSO/GSO when there is
urgent data" (33cf71cee1). It also removes some unnecessary code
from tcp_current_mss that didn't work as intented either (could
be that something was changed down the road, or it might have
been broken since the dawn of time) because it only works once
urg is already written while this bug shows up starting from
~64k before the urg point.
The retransmissions already are split to mss sized chunks, so
only new data sending paths need splitting in case they have
a segment otherwise suitable for gso/tso. The actually check
can be improved to be more narrow but since this is late -rc
already, I'll postpone thinking the more fine-grained things.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the hardware supports the 64bit DMA address in design,
but later found that it actually not working.
This patch reduced the rang to 32bit.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the hardware design, except the first chip on the market,
other chips needs to setup the clock source for MAC processor
implicitly through Global Host Control Register(GHC).
(Strange design huh?)
10/100M uses the PCI-E as clock source, and 1G uses GPHY.
And I reordered the code a little, to make it easier to read.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Fixed-by: "akeemting" <akeem@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace HTB_ACCNT() macro with inlines to make it more readable.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2T() is currently used only in one place (and has one spurious
parameter, btw), so let's: 'get rid of L2T completely, and just
use "qdisc_l2t(rate, size)" directly.' - quote & feedback from
David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet data read from the RX buffer the when the RSV is at the end of the RX
buffer does not warp around. This causes packet loss, as the actual data is
never read. Fix this by calculating the right packet data location.
Thanks to Shachar Shemesh for suggesting the fix.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
