The user_skb maybe be leaked if the operation on it failed and codes
skipped into the label "out:" without calling genlmsg_unicast.
Cc: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make defconfig reports:
warning: (NETFILTER_XT_TARGET_LOG) selects NF_LOG_IPV6 which has unmet direct dependencies (NET && INET && IPV6 && NETFILTER && NETFILTER_ADVANCED)
Fixes: d79a61d netfilter: NETFILTER_XT_TARGET_LOG selects NF_LOG_*
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
pull request: Netfilter/IPVS fixes for net
The following patchset contains seven Netfilter fixes for your net
tree, they are:
1) Make the NAT infrastructure independent of x_tables, some users are
already starting to test nf_tables with NAT without enabling x_tables.
Without this patch for Kconfig, there's a superfluous dependency
between NAT and x_tables.
2) Allow to use 0 in the cgroup match, the kernel rejects with -EINVAL
with no good reason. From Daniel Borkmann.
3) Select CONFIG_NF_NAT from the nf_tables NAT expression, this also
resolves another NAT dependency with x_tables.
4) Use HAVE_JUMP_LABEL instead of CONFIG_JUMP_LABEL in the Netfilter hook
code as elsewhere in the kernel to resolve toolchain problems, from
Zhouyi Zhou.
5) Use iptunnel_handle_offloads() to set up tunnel encapsulation
depending on the offload capabilities, reported by Alex Gartrell
patch from Julian Anastasov.
6) Fix wrong family when registering the ip_vs_local_reply6() hook,
also from Julian.
7) Select the NF_LOG_* symbols from NETFILTER_XT_TARGET_LOG. Rafał
Miłecki reported that when jumping from 3.16 to 3.17-rc, his log
target is not selected anymore due to changes in the previous
development cycle to accomodate the full logging support for
nf_tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.
This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qeth device is queried for ethtool data, hardware operation
is performed to extract the necessary information from the card.
If the card is not online at the moment (e.g. it is undergoing
recovery), this operation produces undesired effects like
temporarily freezing the system. This patch prevents execution
of the hardware query operation when the card is not online.
In such case, ioctl() operation returns error with errno ENODEV.
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calxeda 1G/10G XGMAC Ethernet support should be available only on
Calxeda ECX-1000/2000 (Highbank/Midway) platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is already up, the following sequence makes the kernel
block completely:
ip link set dev eth0 down
ip link set dev eth0 up
This is because on suspended phy, the following lines
__lpc_eth_reset(pldat);
__lpc_eth_init(pldat);
make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be
(re-)activated low-level first.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.
First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.
Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().
v2: Added logging messages per Prashant's request
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We ran into a case on ppc64 running mariadb where io_getevents would
return zeroed out I/O events. After adding instrumentation, it became
clear that there was some missing synchronization between reading the
tail pointer and the events themselves. This small patch fixes the
problem in testing.
Thanks to Zach for helping to look into this, and suggesting the fix.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
Analogous to commit 8858d88a25
that fixed commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
QUEUE_FLAG_NO_SG_MERGE is set at default for blk-mq devices,
so bio->bi_phys_segment computed may be bigger than
queue_max_segments(q) for blk-mq devices, then drivers will
fail to handle the case, for example, BUG_ON() in
virtio_queue_rq() can be triggerd for virtio-blk:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1359146
This patch fixes the issue by ignoring the QUEUE_FLAG_NO_SG_MERGE
flag if the computed bio->bi_phys_segment is bigger than
queue_max_segments(q), and the regression is caused by commit
05f1dd53152173(block: add queue flag for disabling SG merging).
Reported-by: Kick In <pierre-andre.morey@canonical.com>
Tested-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
nouveau keeps track in userspace whether a buffer is being
written to or being read, but it doesn't use that information.
Change this to allow multiple readers on the same bo.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Maintain the original order to handle VRAM/GART/mixed correctly for <nv50,
it's likely not as important on newer cards.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
With the conversion to the reservation api this should be safe.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Final driver! \o/
This is not a proper dma_fence because the hardware may never signal
anything, so don't use dma-buf with qxl, ever.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Use the new fence interface on vmwgfx too.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
---
Changes since v1:
Fix a sleeping function called from invalid context in enable_signaling.
Only one type was ever used. This is needed to simplify the fence
support in the next commit.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
If the balloon driver is adding additional memory regions to the
balloon and add_memory() fails it will likely continuously fail so
cancel the balloon operation.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
Always freeze processes when suspending and thaw processes when resuming
to prevent a race noticeable with HVM guests.
This prevents a deadlock where the khubd kthread (which is designed to
be freezable) acquires a usb device lock and then tries to allocate
memory which requires the disk which hasn't been resumed yet.
Meanwhile, the xenwatch thread deadlocks waiting for the usb device
lock.
Freezing processes fixes this because the khubd thread is only thawed
after the xenwatch thread finishes resuming all the devices.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: stable@vger.kernel.org
Adds ipu_dump() which dumps IPU register state to debug.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_cpmem_dump() which dumps a channel's cpmem to debug.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds support for the following planar and partial-planar formats:
YUV422
NV12
NV16
Signed-off-by: Dmitry Eremin-Solenikov <dmitry_eremin@mentor.com>
Signed-off-by: Mohsin Kazmi <mohsin_kazmi@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Unified base offset and Y plane offset into a single variable,
moved all ipu_cpmem_set_buffer calls to a single location.
Removed NV21 and NV61 for now. The IDMAC doesn't understand U/V
order for chroma interleaved formats, so we'd need to work around
this by implenting U/V switching via the CSC unit.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a second buffer physaddr to struct ipu_image, for double-buffering
support.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_cpmem_set_axi_id() to set which AXI bus master the channel
will use to transfer data onto AXI bus.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_idmac_lock_enable(), which enables or disables channel
burst locking.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the function ipu_idmac_enable_watermark(), which enables or disables
watermarking in the IDMAC channel. Enabling watermarking can increase a
channel's AXI bus arbitration priority.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_stride_to_bytes(), which converts a pixel stride to bytes,
suitable for passing to cpmem.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds __ipu_idmac_reset_current_buffer() that resets a channel's
internal current buffer pointer so that transfers start from buffer
0 on the next channel enable.
This operation is required for channel linking to work correctly,
for instance video capture pipelines that carry out image rotations
will fail after the first streaming unless this function is called
for each channel before re-enabling the channels.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add the reverse of ipu_idmac_select_buffer(), that is, clear a buffer
ready status in a channel.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add ipu_idmac_buffer_is_ready(), returns true if the given buffer in
the given channel is set ready (owned by IPU), or false if not ready
(owned by CPU core).
Support has been added for third buffer, there is no support yet for
triple-buffering in idmac channels, but this function checks
buffer-ready for third buffer in case this support is added later.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Move the IDMAC channel names to imx-ipu-v3.h, to make the names
available outside IPU. Add a couple new channels in the process
(async display BG/FG, channels 24 and 29).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add simple helper function returning true if passed pixel format is one
of supported planar ones.
Signed-off-by: Dmitry Eremin-Solenikov <dmitry_eremin@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add two functions:
- ipu_degrees_to_rot_mode(): converts a degrees, hflip, and vflip setting
to an IPU rotation mode.
- ipu_rot_mode_to_degrees(): converts an IPU rotation mode with given hflip
and vflip settings to degrees.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add ipu_mbus_code_to_colorspace() to find ipu_color_space from a
media bus pixel format code.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_smfc_set_watermark() which programs a channel's SMFC FIFO
levels at which the watermark signal is set and cleared.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Convert the smfc object to be specific to a single smfc channel.
Add ipu_smfc_{get|put} to retrieve and release a single smfc channel
for exclusive use, and add use counter to ipu_smfc_{enable|disable}.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Move the SMFC module enable/disable helpers into the ipu-smfc submodule.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the Image Converter (IC) unit.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Condensed the three CSC setup functions into a single one that
uses static tables to set up the CSC task parameters.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the Camera Sensor Interface (CSI) unit required for video capture.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Removed the unused clk_get_rate in ipu_csi_init_interface and the
ipu_csi_ccir_err_detection_enable/disable functions.
Checkpatch cleanup.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The driver was not bound checking the received length byte to ensure it was within the
the buffer size that is allocated for SMBus blocks. This resulted in buffer overflows
whenever an invalid length byte was received.
It also failed to ensure the length byte was not zero. If it received zero, it would end up
in an infinite loop as the at91_twi_read_next_byte function returned immediately without
allowing RHR to be read to clear the RXRDY interrupt.
Tested agaisnt a SMBus compliant battery.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In rk3x SOC, the I2C controller can receive/transmit up to 32 bytes data
in one chunk, so the size of data to be write/read to/from TXDATAx/RXDATAx
must be less than or equal 32 bytes at a time.
Tested on rk3288-pinky board, elan receive 158 bytes data.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Max Schwarz <max.schwarz@online.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
