* 'features/imx27-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
devicetree-bindings: Add documentation for i.MX generic boards
ARM i.MX: Add phytec phycore-i.MX27 (aka pcm038) devicetree support
ARM i.MX27: Add devicetree support
It was observed on a mx31pdk board that audio playback only worked when the bootloader was Redboot, and
did not work when U-boot was used.
Comparing the sources of these bootloaders showed that the AIPS registers were not setup in U-boot.
Instead of relying on the bootloader to setup the AIPS registers, do it in the kernel so that audio
playback can work independantly of the bootloader being used.
Copied the AIPS settings from Redboot to the kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The LPM field of register CCMR is used to select the mode that the processor will run
when it goes to WFI.
When mx31 enters in WFI mode the LPM field is at its reset value of 0,
which configures the mx31 to enter in "wait mode".
On mx35, the LPM field on mx35 is also at 0 after reset, which corresponds
to "run mode" instead of "wait mode".
Instead of relying on the reset value of LPM to set the low power mode for
WFI, configure mx31 and mx35 to run in "wait mode"
Reported-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic devicetree support for i.MX27 based SoCs.
Only the bindings for which drivers exist are added here:
- UART
- fec
- CSPI
- I2C
- watchdog
- gpio
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'imx/driver' of git://git.linaro.org/people/shawnguo/linux-2.6: (3 commits)
ARM: imx6q: add cko1 clock
ARM: mxc: make imx_dma_is_general_purpose more generic for sdma
ARM: imx6: Rename DEBUG_IMX6Q_UART to UART4
eMMa-PrP device included in Freescale i.MX2 chips can also
be used separately to process memory buffers. This patch
provides arch glue code for the driver which provides this
functionality.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'features/cs89x0' of git://git.pengutronix.de/git/imx/linux-2.6:
CS89x0 : add CS89x0 platform device to the iMX31ADS board
CS89x0 : remove QQ2440 board support from the CS89x0 driver
CS89x0 : add CS89x0 platform device to the iMX21ADS board
CS89x0 : add platform driver support
sdma device names vary for different SoC. So we just check
whether it includes "sdma" substring.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Different boards may use differenct UART ports for debugging.
To be able to add different debug UART configurations (e.g. UART2),
rename the existing general DEBUG_IMX6Q_UART to DEBUG_IMX6Q_UART4.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Use struct usb_otg members with OTG specific functions instead
of usb_phy members.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into depends/rmk/for-armsoc
There were conflicts between fixes going in after 3.3-rc1 and
Russell's stable arm-soc base branch. Resolving it in the dependency
branch so that each topic branch shares the same resolution.
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9g45.c
Add CS89x0 networking support to the iMX31ADS board by using the
platform driver support in the CS89x0 driver.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix the following build error found when building imx_v4_v5_defconfig:
CC arch/arm/mach-imx/mach-imx27ipcam.o
In file included from arch/arm/plat-mxc/include/mach/iomux-mx27.h:23,
from arch/arm/mach-imx/mach-imx27ipcam.c:22:
arch/arm/plat-mxc/include/mach/iomux-v1.h:99: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'imx_iomuxv1_init'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=P4kO
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The restart support was missed from the initial imx6q submission.
The mxc_restart() does not work for imx6q. Instead, this patch adds
the restart for imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* imx/board: (4 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
Updated to v3.2-rc6, conflicts:
arch/arm/kernel/setup.c
* imx6/pm:
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
This adds necessary defines for the CSPI3 module (activated with
imx25_add_spi_imx2()) to work on the CSI pins (alternative mode 7).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Two problems exist in the current i.MX5 pm suspend/resume and idle
functions. The first is the current i.MX5 suspend routine will call
tzic_enable_wake(1) to set wake source, this will set all enabled
irq as wake source rather than those wake capable. The second
is i.MX5 idle will call mx5_cpu_lp_set() to prepare enter low power
mode, but it forgets to call wfi instruction to enter this mode.
To fix these two problems, using generic irq chip pm interface and
modify function imx5_idle().
[Tested by Shawn Guo on imx51 babbage board.
Tested by Hui Wang on imx51 pdk board.]
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The IPU internally works on 32bit colors. It can arbitrarily map
between pixel formats and internal representation and also between
internal representation and the physical connection to the display.
The driver used to change the mapping between internal representation
and display connection depending on the user selected bpp which is
wrong. Instead, the mapping is specified by the hardware, so an
additional field in platform data is added to describe the connection
between i.MX and the display. The default for this field is RGB666
which seems to be the only configuration which works without this
patch, so I assumed that all in Kernel boards are connected this
way.
This patch has been tested on a RGB666 connected display and a
RGB888 connected display in both 16bpp and 32bpp modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
map_io is the only place to call iotable_init.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
[shawn.guo: rename imx_clock_map_io() to imx6q_clock_map_io()]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Convert the SMP imx platforms to use the global gic_handle_irq()
function instead a private function.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Before introducing a global gic_handle_irq(), rename
MXC's version to mxc_gic_handle_irq(). This function will be
removed altogether in a later patch.
Cc: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The patch removes imx_idle hook and use pm_idle instead to get imx
arch_idle prepared for the cleanup. It's suggested by Russel King
as below.
> The final removal of mach/system.h depends on getting rid of the arch_idle
> thing. While going through these headers, I was dismayed to find these:
>
> arch/arm/mach-s3c2410/include/mach/system.h:void (*s3c24xx_idle)(void);
> arch/arm/plat-mxc/include/mach/system.h:extern void (*imx_idle)(void);
>
> when we have a perfectly good pm_idle hook already in place - so there's
> no excuse for these especially when other platforms are already using
> pm_idle to hook their platform specific idle function into. This is
> something that better be gone at the next merge window!
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since commit (167a19d2: ARM: imx: Introduce generic function for displaying silicon revision)
we no longer need the chip revision strings, so remove them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch "ARM: gic: consolidate PPI handling" removes the usage
of test_for_ltirq. After the merge of imx6q remove this there, too.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
* 'next/soc' of git://git.linaro.org/people/arnd/arm-soc: (21 commits)
MAINTAINERS: add ARM/FREESCALE IMX6 entry
arm/imx: merge i.MX3 and i.MX6
arm/imx6q: add suspend/resume support
arm/imx6q: add device tree machine support
arm/imx6q: add smp and cpu hotplug support
arm/imx6q: add core drivers clock, gpc, mmdc and src
arm/imx: add gic_handle_irq function
arm/imx6q: add core definitions and low-level debug uart
arm/imx6q: add device tree source
ARM: highbank: add suspend support
ARM: highbank: Add cpu hotplug support
ARM: highbank: add SMP support
MAINTAINERS: add Calxeda Highbank ARM platform
ARM: add Highbank core platform support
ARM: highbank: add devicetree source
ARM: l2x0: add empty l2x0_of_init
picoxcell: add a definition of VMALLOC_END
picoxcell: remove custom ioremap implementation
picoxcell: add the DTS for the PC7302 board
picoxcell: add the DTS for pc3x2 and pc3x3 devices
...
Fix up trivial conflicts in arch/arm/Kconfig, and some more header file
conflicts in arch/arm/mach-omap2/board-generic.c (as per an ealier merge
by Arnd).
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
* 'next/cross-platform' of git://git.linaro.org/people/arnd/arm-soc:
arm/imx: use Kconfig choice for low-level debug UART selection
ARM: realview: use Kconfig choice for debug UART selection
ARM: plat-samsung: use Kconfig choice for debug UART selection
ARM: versatile: convert logical CPU numbers to physical numbers
ARM: ux500: convert logical CPU numbers to physical numbers
ARM: shmobile: convert logical CPU numbers to physical numbers
ARM: msm: convert logical CPU numbers to physical numbers
ARM: exynos4: convert logical CPU numbers to physical numbers
Fix up trivial conflict (config DEBUG_S3C_UART move/split vs addition of
ARM_KPROBES_TEST option) in arch/arm/Kconfig.debug
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/driver' of git://git.linaro.org/people/arnd/arm-soc:
hw_random: add driver for atmel true hardware random number generator
ARM: at91: at91sam9g45: add trng clock and platform device
MX53 Enable the AHCI SATA on MX53 SMD board
MX53 Enable the AHCI SATA on MX53 LOCO board
MX53 Enable the AHCI SATA on MX53 ARD board
AHCI Add the AHCI SATA feature on the MX53 platforms
Fix pata imx resource
ARM: imx: Define functions for registering PATA
ARM: imx: Add PATA clock support
ARM: imx: Add PATA resources for other i.MX processors
imx: efika: Enable pata.
imx51: add pata clock
imx51: add pata device
Fix up trivial conflict (new selects next to each other from separate
branches for EFIKA_COMMON) in arch/arm/mach-mx5/Kconfig
