Adds support for setting HDMI platform data for Exynos4X12 SoCs.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Calling the dmtimer function omap_dm_timer_set_source() fails if following a
call to pm_runtime_put() to disable the timer. For example the following
sequence would fail to set the parent clock ...
omap_dm_timer_stop(gptimer);
omap_dm_timer_set_source(gptimer, OMAP_TIMER_SRC_32_KHZ);
The following error message would be seen ...
omap_dm_timer_set_source: failed to set timer_32k_ck as parent
The problem is that, by design, pm_runtime_put() simply decrements the usage
count and returns before the timer has actually been disabled. Therefore,
setting the parent clock failed because the timer was still active when the
trying to set the parent clock. Setting a parent clock will fail if the clock
you are setting the parent of has a non-zero usage count. To ensure that this
does not fail use pm_runtime_put_sync() when disabling the timer.
Note that this will not be seen on OMAP1 devices, because these devices do
not use the clock framework for dmtimers.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to do left shift (cfg->num + LP8788_ISINK_SCALE_OFFSET) bits for
updating scale configuration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().
Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().
Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().
Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, this driver originally checked
the pci_dev subsystem_device in order to make sure that the
pci_dev was compatible with this driver. The cleanup of the
"find pci device" code removed this check. Add it back.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, the comedi pci drivers that try to
locate an unused pci device with the pci_is_enabled() test
might actually skip over a perfectly good unused device. This
test is also not consistent with the other comedi pci drivers.
Remove the test from all the comedi pci drivers.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are three fixes for v3.6-rc1. All on the MUSB driver and
quite obvious. First there's a Kconfig change which was missed
earlier, then there is a fix for the usage of the resource name
and lastly a fix for pm_runtime usage and device initialization.
The last fix is rather critical as it can end up in situations
where we try to access device's register with clocks disabled,
which will cause a Data Abort exception (on ARM).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bAd9
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.6-rc1
Here are three fixes for v3.6-rc1. All on the MUSB driver and
quite obvious. First there's a Kconfig change which was missed
earlier, then there is a fix for the usage of the resource name
and lastly a fix for pm_runtime usage and device initialization.
The last fix is rather critical as it can end up in situations
where we try to access device's register with clocks disabled,
which will cause a Data Abort exception (on ARM).
Fixes the following sparse warning:
arch/arm/plat-samsung/pm.c:77:21:
warning: symbol 'uart_save' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit d670ac019f (ARM: SAMSUNG: DMA Cleanup as per sparse) changed the
prototype of the s3c2410_dma_* functions to use the enum dma_ch instead
of an generic unsigned int.
In the s3c24xx dma.c s3c2410_dma_enqueue seems to have been forgotten,
the other functions there were changed correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 2b90807549 (spi: s3c64xx: add device tree support) requires
the DMACH_DT_PROP element in the dma_ch enum. It's not used on non-DT
platforms but has to be present nevertheless.
So mimic the dummy-add of DMACH_DT_PROP on s3c64xx for s3c24xx
machines, to correct the build breakage for the s3c24xx variants
using the s3c64xx-spi-driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This reverts commit 58f0829b71.
Converstion to per-pwrdm per/post transition calls was a bit
premature. Only tracking MPU, PER & CORE in the idle path means we
lose the accounting for all the other powerdomains which may also
transition in idle. On OMAP3, due to autodeps, several powerdomains
transition along with MPU (e.g. DSS, USBHOST), and the accounting for
these was lost with this patch. Since the accounting includes the
context loss counters, drivers for devices in those power domains
would never notice context lost, so would likely hang after any
off-mode transitions.
This patch should be revisited when the upcoming clkdm/pwrmdm/voltdm
use-counting seires is merged since then we can properly do accounting
without relying on a call in the idle path.
In addition, the original patch had another bug because the PER
powerdomain accounting was not updated until after the GPIO resume
hook is called. Since gpio_resume_after_idle() checks the context
loss count (which is not yet updated) it would not properly restore
context, leaving the GPIO banks in an undefined state.
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on 3430/n900, OMAP3530/Overo Fire, 3730/Overo FireSTORM,
3730/Beagle-xM.
Signed-off-by: Kevin Hilman <khilman@ti.com>
When we encounter an xHCI host that needs the XHCI_TRUST_TX_LENGTH
quirk, the xHCI driver ends up spewing messages about the quirk into
dmesg every time a short packet occurs. Change the xHCI driver to
rate-limit such warnings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Matthew Hall <mhall@mhcomputing.net>
Reported-by: Gary E. Miller <gem@rellim.com>
Gary reports that with recent kernels, he notices more xHCI driver
warnings:
xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host. When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.
Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered. Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.
This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc627 "xhci: Add new short TX quirk
for Fresco Logic host."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Gary E. Miller <gem@rellim.com>
Cc: stable@vger.kernel.org
The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds. In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings. Extend the reset and CNR polling timeout to 10 seconds each.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd8d "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Edwin Klein Mentink <e.kleinmentink@zonnet.nl>
Cc: stable@vger.kernel.org
The conversion to voltage tables in
commit a3beb74261
"regulator: ab3100: Use regulator_list_voltage_table()"
missed to add the voltage table to the buck. Fix this and
it works like a charm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mask used in anatop_get_voltage_sel does not match the mask used in
anatop_set_voltage_sel.
We need to do left shift anatop_reg->vol_bit_shift bits for the correct mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As per datasheet, the vin pin for the regulator is named
as vin_sm0, vin_sm1, vin_sm2 for sm0, sm1 and sm2 respectively.
Correcting the names in driver and documentation to match with
datasheet.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below error handling cases:
1. If reading PALMAS_SMPS_CTRL fails, simply returns ret rather than goto
err_unregister_regulator because we have not call regulator_register().
2. If palmas_ldo_init() fails, we need to call regulator_unregister() for the
regulator we just successfully registered in this for loop iteration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code uses wrong calls palmas_smps_[read|write] in palmas_ldo_init(),
should be palmas_ldo_[read|write] instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes below issues when choosing selector:
1. Current code returns negative selector if min_uV < 900000 which is wrong.
For example, it is possible to satisfy the request with selector = 1 if
the requested min_uV is 850000.
2. Current code may select a voltage lower than requested min_uV.
For example, if the requested min_uV is 945000, current code chooses
selector = 1 which is lower than requested min_uV.
DIV_ROUND_UP to avoid this case.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When CONFIG_SND_VERBOSE_PRINTK=y is set, the debug print in
hda_auto_parser.c looks really ugly like:
ALSA sound/pci/hda/hda_auto_parser.c:331 mono: mono_out=0x0
ALSA sound/pci/hda/hda_auto_parser.c:334 dig-out=0x12/0x0
ALSA sound/pci/hda/hda_auto_parser.c:335 inputs:
ALSA sound/pci/hda/hda_auto_parser.c:339 Mic=0x11ALSA sound/pci/hda/hda_auto_parser.c:339 Line=0x10
ALSA sound/pci/hda/hda_auto_parser.c:341
ALSA sound/pci/hda/hda_auto_parser.c:343 dig-in=0x13
Better to put one item at each line.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The check for the mux_signal callback was wrong which prevents us to
configure the 6pin port's FSR/CLKR signal mux.
Reported-by: CF Adad <cfadad@rocketmail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org (3.4+)
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the pointers that are allocated with devm_kzalloc will be automatically freed,
at unload time.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the auto model is the default, these quirks are redundant
and can be removed.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This computer is confirmed working with model=auto on kernel 3.2.
Also, parsing fails with hda-emu with the current model.
Cc: stable@kernel.org (3.2+)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tidy up a small typo in the HSI function group list.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also properly indent the HB IDs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is not point in having arch_id as parameter of __arch_decomp_setup(),
nothing in it uses arch_id. The machine id is already exported (and used)
with symbol __machine_arch_type as per mach-types.h.
Removing the pointless macro as well.
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
vcxio, v2v1 and v1v8 are expected to be always on, update the dtsi
for twl6030 to reflect this.
commit '86f5fc' regulator: core: Mark all DT based boards as having
full constraints) caused these to be disabled at late boot causing
OMAP4 boards (using twl6030) to lockup.
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Reported-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Just a small typo fix to make lsxl dtbs compile
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The first idea of the CAN FD implementation started with a new struct
canfd_frame to be used for both CAN FD frames and legacy CAN frames.
The now mainlined implementation supports both CAN frame types simultaneously
and distinguishes them only by their required sizes: CAN_MTU and CANFD_MTU.
Only the struct canfd_frame contains a flags element which is needed for the
additional CAN FD information. As CAN FD implicitly means that the 'Extened
Data Length' mode is enabled the formerly defined CANFD_EDL bit became
redundant and also confusing as an unset bit would be an error and would
always need to be tested.
This patch removes the obsolete CANFD_EDL bit and clarifies the documentation
for the use of struct canfd_frame and the CAN FD relevant flags.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some 8086:10c9 NICs have a problem completing the ethtool loopback test.
The result looks like this:
ethtool -t eth1
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 13
Link test (on/offline) 0
A bisect clearly points to commit a95a07445e.
However that seems to only trigger the bug. While adding some printk the
problem disappeared, so this might be a timing issue. After some trial and
error I discovered that adding a small delay just before igb_write_phy_reg()
in igb_integrated_phy_loopback() allows the loopback test to succeed.
I was unable to figure out the root cause so far but I expect it to be
somewhere in the following executing path
igb_integrated_phy_loopback
->igb_write_phy_reg_igp
->igb_write_phy_reg_mdic
->igb_acquire_phy_82575
->igb_acquire_swfw_sync_82575
The problem could only be observed on 8086:10c9 NICs so far and not all
of them show the behaviour. I did not restrict the workaround to this
type of NIC as it should do no harm to other igb NICs.
With the patch below the loopback test succeeded 500 times in a row
using a NIC that would otherwise fail.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit. This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.
Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: Fabio Futigami <ffutigam@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
The random config builds with PM and !ARM_CPU_SUSPEND breaks with below
error on omap2plus_defconfig.
arch/arm/mach-omap2/sleep44xx.S:323: undefined reference to `cpu_resume'
arch/arm/mach-omap2/omap-mpuss-lowpower.c:278: undefined reference to `cpu_suspend'
This is because recently merged OMAP5 platform shares the common files
with OMAP4 but doesn't select ARM_CPU_SUSPEND. Without the ARM_CPU_SUSPEND
the sleep code is meaningless.
Fix the same by adding ARM_CPU_SUSPEND for OMAP5. The suggestion came from
Russell King in an off-list discussion.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Naming of emma-prp related clocks for the i.MX27 is not correct.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add am33xx wdt node.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[tony@atomide.com: I messed up and produced an empty commit db27ac80 with stg apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpc4 to the end of the automatically processed gpio controllers so
we don't taint the automatic offset calculation.
This bug caused all controllers coming after gpc4 to map to the
incorrect address. The result is <&gpd1 0 0 0 0> would actually map to
GPIO 0 in gpd0.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
