For Northstart Plus SoCs, we cannot detect the switch because only the
revision information is provied in the Management page, instead, rely on
Device Tree to tell us the chip id, and pass it down using the
b53_platform_data structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for TSE PCS that uses SGMII adapter when the phy-mode of
the dwmac is set to sgmii.
Signed-off-by: Tien Hock Loh <thloh@altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All inet6_netconf_notify_devconf() callers are in process context,
so we can use GFP_KERNEL allocations if we take care of not holding
a rwlock while not needed in ip6mr (we hold RTNL there)
Fixes: d67b8c616b ("netconf: advertise mc_forwarding status")
Fixes: f3a1bfb11c ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_forward_change() runs with RTNL held.
We are allowed to sleep if required.
If we use __in_dev_get_rtnl() instead of __in_dev_get_rcu(),
we no longer have to use GFP_ATOMIC allocations in
inet_netconf_notify_devconf(), meaning we are less likely to miss
notifications under memory pressure, and wont touch precious memory
reserves either and risk dropping incoming packets.
inet_netconf_get_devconf() can also use GFP_KERNEL allocation.
Fixes: edc9e74893 ("rtnl/ipv4: use netconf msg to advertise forwarding status")
Fixes: 9e5511106f ("rtnl/ipv4: add support of RTM_GETNETCONF")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Mason says:
====================
net: ethernet: bgmac: Add platform device support
David Miller, Please consider including patches 1-5 in net-next
Florian Fainelli, Please consider including patches 6 & 7 in
devicetree/next
Changes in v2:
* Made device tree binding changes suggested by Sergei Shtylyov,
Ray Jui, Rob Herring, Florian Fainelli, and Arnd Bergmann
* Removed devm_* error paths in the bgmac_platform.c suggested by
Florian Fainelli
* Added Arnd Bergmann's Acked-by to the first 5 (there were changes
outlined in the bullets above, but I believe them to be minor enough
for him to not revoke his acks)
This patch series adds support for other, non-bcma iProc SoC's to the
bgmac driver. This series only adds NSP support, but we are interested
in adding support for the Cygnus and NS2 families (with more possible
down the road).
To support non-bcma enabled SoCs, we need to add the standard device
tree "platform device" support. Unfortunately, this driver is very
tighly coupled with the bcma bus and much unwinding is needed. I tried
to break this up into a number of patches to make it more obvious what
was being done to add platform device support. I was able to verify
that the bcma code still works using a 53012K board (NS SoC), and that
the platform code works using a 58625K board (NSP SoC).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcma portion of the driver has been split off into a bcma specific
driver. This has been mirrored for the platform driver. The last
references to the bcma core struct have been changed into a generic
function call. These function calls are wrappers to either the original
bcma code or new platform functions that access the same areas via MMIO.
This necessitated adding function pointers for both platform and bcma to
hide which backend is being used from the generic bgmac code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver is using the bcma provides device ID and revision, as
well as the SoC ID and package, to determine which features are
necessary to enable, reset, etc in the driver. In anticipation of
removing the bcma requirement for this driver, these must be changed to
not reference that struct. In place of that, each "feature" has been
given a flag, and the flags are enabled for their respective device and
SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the BCMA MDIO phy into a separate file, as it is very tightly
coupled with the BCMA bus. This will help with the upcoming BCMA
removal from the bgmac driver. Optimally, this should be moved into
phy drivers, but it is too tightly coupled with the bgmac driver to
effectively move it without more changes to the driver.
Note: the phy_reset was intentionally removed, as the mdio phy subsystem
automatically resets the phy if a reset function pointer is present. In
addition to the moving of the driver, this reset function is added.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma buffer allocation, etc references a dma_dev device pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. Add a
dma_dev device pointer to the bgmac stuct and reference that instead.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac_* print wrappers call dev_* prints with the dev pointer from
the bcma core. In anticipation of removing the bcma requirement for
this driver, these must be changed to not reference that struct. So,
simply change all of the bgmac_* prints to their dev_* counterparts. In
some cases netdev_* prints are more appropriate, so change those as
well.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.
Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: remove the redundant code
Remove the unnacessary code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90186af404 ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
net: support MPLS in IPv4 and UDP
This short series provides support for MPLS in IPv4 (RFC4023), and by
virtue of FOU, MPLS in UDP (RFC7510).
The changes are as follows:
1. Teach tunnel4.c about AF_MPLS, it already understands AF_INET and
AF_INET6
2. Enhance IPIP and SIT to handle MPLS. Both already handle IPv4.
SIT also already handles IPv6.
3. Trivially enhance MPLS to allow routes over SIT and IPIP tunnels.
A corresponding patch set for iproute2 has also been provided.
Changes since v1
* Correct inverted IPIP protocol logic in SIT patch
* Provide usage example below
Sample configuration follows:
* The following creates a tunnel and routes MPLS packets whose outermost
label is 100 over it. The forwarded packets will have the outermost label
stack entry, 100, removed and two label stack entries added, the
outermost having label 200 and the next having label 300.
The local end-point for the tunnel is 10.0.99.192 and the remote
endpoint is 10.0.99.193.
The local address for encapsulated packets is 10.0.98.192 and the
remote address is 10.0.98.193.
# Create an MPLS over IPv4 tunnel using the IPIP driver
ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
ttl 225 mode mplsip
# Bring the tunnel up and an add an IPv4 address and route
ip link set up dev tun1
ip addr add 10.0.98.192/24 dev tun1
# Set MPLS route
# Allow MPLS forwarding of packets recieved on eth0
echo 1 > /proc/sys/net/mpls/conf/eth0/input
# Larger than label to be routed (100)
echo 101 > /proc/sys/net/mpls/platform_labels
ip -f mpls route add 100 as 200/300 via inet 10.0.98.193
* For FOU (in this case MPLS over UDP) a tunnel may created using:
# Packets recieved on UDP port 6635 are MPLS over UDP (IP proto 137)
ip fou add port 6635 ipproto 137
# Create the tunnel netdev
ip link add name tun1 type ipip remote 10.0.99.193 local 10.0.99.192 \
ttl 225 mode mplsip encap fou encap-sport auto encap-dport 6635
IPv4 address, link and route, and MPLS routing commands are as per
the MPLS over IPv4 example
* To use the SIT driver instead of the IPIP driver "ipip" may be substituted
for "sit" in the above examples.
* To create a tunnel that forwards and receives all supported
inner-protocols "mplsip" may be substituted for "any" in the above
examples.
For the IPIP driver this configures both IPv4 and MPLS over IPv4.
For the SIT driver this configures IPv6, IPv4 and MPLS over IPv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow MPLS routes on IPIP and SIT devices now that they
support forwarding MPLS packets.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the IPIP driver to support MPLS over IPv4. The implementation is an
extension of existing support for IPv4 over IPv4 and is based of multiple
inner-protocol support for the SIT driver.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the SIT driver to support MPLS over IPv4. This implementation
extends existing support for IPv6 over IPv4 and IPv4 over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tunnel support to MPLS over IPv4. The implementation extends the
existing differentiation between IPIP and IPv6 over IPv4 to also cover MPLS
over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.
[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1
Suggested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HCI_BREDR naming is confusing since it actually stands for Primary
Bluetooth Controller. Which is a term that has been used in the latest
standard. However from a legacy point of view there only really have
been Basic Rate (BR) and Enhanced Data Rate (EDR). Recent versions of
Bluetooth introduced Low Energy (LE) and made this terminology a little
bit confused since Dual Mode Controllers include BR/EDR and LE. To
simplify this the name HCI_PRIMARY stands for the Primary Controller
which can be a single mode or dual mode controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller device attributes are not used and expose no valuable
information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection link attributes are not used and expose no valuable
information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When we introduced GSO support, if using auth the auth chunk was being
left queued on the packet even after the final segment was generated.
Later on sctp_transmit_packet it calls sctp_packet_reset, which zeroed
the packet len while not accounting for this left-over. This caused more
space to be used the next packet due to the chunk still being queued,
but space which wasn't allocated as its size wasn't accounted.
The fix is to only queue it back when we know that we are going to
generate another segment.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code generates as static checker warning because htons(ETH_P_IPV6)
is always true. From the context it looks like the && was intended to
be !=.
Fixes: 94758f8de0 ('bnxt_en: Add GRO logic for BCM5731X chips.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
over time there were multiple requests to access different data
structures and fields of task_struct current, so finally add
the helper to access 'current' as-is. Tracing bpf programs will do
the rest of walking the pointers via bpf_probe_read().
Note that current can be null and bpf program has to deal it with,
but even dumb passing null into bpf_probe_read() is still safe.
Suggested-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The routing table of every switch in a tree is currently initialized to
all zeros. This is an issue since 0 is a valid port number.
Add a DSA_RTABLE_NONE=-1 constant to initialize the signed values of the
routing table pointing to other switches.
This fixes the device mapping of the mv88e6xxx driver where the port
pointing to the switch itself and to non-existent switches was wrongly
configured to be 0. It is now set to the expected 0xf value.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1ZSd
-----END PGP SIGNATURE-----
Merge tag 'rxrpc-rewrite-20160706' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Improve conn/call lookup and fix call number generation [ver #3]
I've fixed a couple of patch descriptions and excised the patch that
duplicated the connections list for reconsideration at a later date.
For reference, the excised patch is sitting on the rxrpc-experimental
branch of my git tree, based on top of the rxrpc-rewrite branch. Diffing
it against yesterday's tag shows no differences.
Would you prefer the patch set to be emailed afresh instead of a git-pull
request?
David
---
Here's the next part of the AF_RXRPC rewrite. The two main purposes of
this set are to fix the call number handling and to make use of RCU when
looking up the connection or call to pass a received packet to.
Important changes in this set include:
(1) Avoidance of placing stack data into SG lists in rxkad so that kernel
stacks can become vmalloc'd (Herbert Xu).
(2) Calls cease pinning the connection they used as soon as possible,
which allows the connection to be discarded sooner and allows the call
channel on that connection to be reused earlier.
(3) Make each call channel on a connection have a separate and independent
call number space rather than having a shared number space for the
connection. Call numbers should increment monotonically per channel
on the client, and the server should ignore a call with a lower call
number for that channel than the latest it has seen. The RESPONSE
packet sets the minimum values of each call ID counter on a
connection.
(4) Look up calls by indexing the channel array on a connection rather
than by keeping calls in an rbtree on that connection. Also look up
calls using the channel array rather than using a hashtable.
The call hashtable can then be removed.
(5) Call terminal statuses are cached in the channel array for the last
call. It is assumed that if we the server have seen call N, then the
client no longer cares about call N-1 on the same channel.
This will allow retransmission of the terminal status in future
without the need to keep the rxrpc_call struct around.
(6) Peer lookups are moved out of common connection handling code and into
service connection handling code as client connections (a) must point
to a peer before they can be used and (b) are looked up by a
machine-unique connection ID directly, so we only need to look up the
peer first if we're going to deal with a service call.
(7) The reference count on a connection is held elevated by 1 whilst it is
alive (ie. idle unused connections have a refcount of 1). The reaper
will attempt to change the refcount from 1->0 and skip if this cannot
be done, whilst look ups only increment the refcount if it's non-zero.
This makes the implementation of RCU lookups easier as we don't have
to get a ref on the connection or a lock on the connection list to
prevent a connection being reaped whilst we're contemplating queueing
a packet that initiates a new service call upon it.
If we need to get a connection, but there's a dead connection in the
tree, we use rb_replace_node() to replace the dead one with a new one.
(8) Use a seqlock to validate the walk over the service connection rbtree
attached to a peer when it's being walked in RCU mode.
(9) Make the incoming call/connection packet handling code use RCU mode
and locks and make it only take a reference if the call/connection
gets queued on a workqueue.
The intention is that the next set will introduce the connection lifetime
management and capacity limits to prevent clients from overloading the
server.
There are some fixes too:
(1) Verifying that a packet coming in to a client connection came from the
expected source.
(2) Fix handling of connection failure in client call creation where we
don't reinitialise the list linkage block and a second attempt to
unlink the failed connection oopses and also we don't set the state
correctly, which causes an assertion failure.
(3) New service calls were being added to the socket's accept queue under
the wrong lock.
Changes:
(V2) In rxrpc_find_service_conn_rcu() initialised the sequence number to 0.
Fixed the RCU handling in conn_service.c by introducing and using
rb_replace_node_rcu() as an RCU-safe alternative in
rxrpc_publish_service_conn().
Modified and used rcu_dereference_raw() to avoid RCU sparse warnings
in rxrpc_find_service_conn_rcu().
Added in some missing RCU dereference wrappers. It seems to be
necessary to turn on CONFIG_PROVE_RCU_REPEATEDLY as well as
CONFIG_SPARSE_RCU_POINTER to get the static __rcu annotation checking
to happen.
Fixed some other sparse warnings, including a missing ntohs() in
jumbo packet processing.
(V3) Fixed some commit descriptions.
Excised the patch that duplicated the connection list to separate out
the procfs list for reconsideration at a later date.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new APIs for eliminating a copy on the receive path. These new APIs also
help in minimizing the number of memory barriers we end up issuing (in the
ringbuffer code) since we can better control when we want to expose the ring
state to the host.
The patch is being resent to address earlier email issues.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hfsc_sched is huge (size: 920, cachelines: 15), but we can get it to 14
cachelines by placing level after filter_cnt (covering 4 byte hole) and
reducing period/nactive/flags to u32 (period is just a counter,
incremented when class becomes active -- 2**32 is plenty for this
purpose, also, long is only 32bit wide on 32bit platforms anyway).
cl_vtperiod is exported to userspace via tc_hfsc_stats, but its period
member is already u32, so no precision is lost there either.
Cc: Michal Soltys <soltys@ziu.info>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently
ignore this message so let's do the same to silence the error message.
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes some issues with interface reconfiguration. It could
for example happen that an AP interface in beacon slot 0 was removed
leaving an IBSS station in one of the other slots. When this happens
the driver never sends out the beacon as it only tries to send a beacon
from slot 0.
Appart from that the tracking of required changes to the beacon config is
relatively complicated and prone to errors.
The approach taken here is to solve reconfiguration issues is to
reconfigure the beacons when any interface changes. This means that
the complexity of deciding whether an interface change may modify the
beacon configuration is gone. It also means that the beacon config will
be reliably updated when an interface is removed.
The issue that a single non-AP interface might not be in beacon
slot 0 and wouldn't be send out is solved by moving it into the
first slot. The TSF value in hardware is adjusted accordingly so
that the timestamp of the beacons stay consistent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The removed ATH9K_SLOT_TIME_X constants simply map the value in microseconds
to the same integer. These constants were not used consistently, so fix the
inconsistency issue by replacing all occurances with the integer equivalent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k driver modifies the TSF for VIFs for the purpose of sending
beacons in a staggered fashion. This patch exposes this VIF specific
adjustment of the TSF value to mac80211. Without the change the TSF
routines handle the hardware TSF value instead of the actual TSF value as
seen on the air.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These changes make ath9k_hw_reset more consistent with other places that
handle the TSF value by using the same helper routine.
A slight improvement is to not assume that a fixed time of 1.5ms has
passed for the initval writes when compared to the first write attempt.
Instead the TSF value is re-calculated which will yield a higher accuracy
of the restored TSF timer.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k TSF handling routines need to be aware of the channel context that
is being modified. With this change the TSF related values that are stored
in each channel context will be correctly tracked and the harware will only
be updated if the modified context is currently the active one.
Without this change the TSF modifications done using these routines would
for example be lost during a hardware reset as done by ath_complete_reset.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacons were not send out at (timestamp % beacon_time == 0) for interfaces
other than the primary one. To send out beacons with the correct timestamp
according to 10.1.3.2 of the 802.11 standard the tsf_adjustment has to be
set to the negative time difference instead of positive. This way the
later beacons get corrected to have a lower (and similar) timestamp with
regard to the beacon from slot 0.
I am not aware about any issues that have been caused by this.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, this simply makes the code easier to understand
because all initialization based on ath9k_platform_data is now within
one function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k_hw_init_macaddr unconditionally returns 0 in all cases, making the
return value unnecessary.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently setting the MAC address via ath9k_platform_data works only due
to the order in which init.c sets common->macaddr, which is done after
ath9k_hw_init_macaddr was executed. It would be better if the latter
was independent of the order in which it's being called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes - this only removes a variable which is set but
never read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices running OpenWrt need this and it makes sense to add this
to ath9k_platform_data as the next patches will add a devicetree
(boolean) property for it as well.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
