This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Atmel MCI controller can drive multiple cards through separate sets
of pins, but only one at a time. This patch adds support for
multiplexing access to the controller so that multiple card slots can be
used as if they were hooked up to separate mmc controllers.
The atmel-mci driver registers each slot as a separate mmc_host. Both
access the same common controller state, but they also have some state
on their own for card detection/write protect handling, and separate
shadows of the MR and SDCR registers.
When one of the slots receives a request from the mmc core, the common
controller state is checked. If it's idle, the request is submitted
immediately. If not, the request is added to a queue. When a request is
done, the queue is checked and if there is a queued request, it is
submitted before the completion callback is called.
This patch also includes a few cleanups and fixes, including a locking
overhaul. I had to change the locking extensively in any case, so I
might as well try to get it right. The driver no longer takes any
irq-safe locks, which may or may not improve the overall system
performance.
This patch also adds a bit of documentation of the internal data
structures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.
Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.
Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Some cards might get upset if we turn off the clock for extended periods
of time. So keep the clock running until the mmc core tells us to turn
it off.
Also, don't reset the controller between each transfer. That was an
attempt to work around earlier bugs, and it never really worked very
well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
With the current system of completed/pending events, things may get
handled in different order depending on which event triggers first. For
example, if the data transfer is complete before the command, the stop
command must be sent after the command is complete, not the data. This
creates a bit of complexity around the stop command.
By having the tasklet go through a sequence of clearly defined states,
things always happen in a certain order even if the events come at
different times, so the stop command can simply be sent when we exit the
"sending data" state because we will never enter that state before the
command has been sent successfully.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This protocol provides some connection handling and negotiated
congestion control. Nokia cellular modems use it for bulk transfers.
It provides packet boundaries (hence SOCK_SEQPACKET). Congestion
control is per packet rather per byte, so we do not re-use the
generic socket memory accounting.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the at32_clock_list array with a linked list.
Clocks can now be registered (added) to the list.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace a magic number with a named constant in the VESA boot code.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Optiarc DVD RW AD-7200A can play audio, but tells it could not.
Signed-off-by: Bodo Eggert <7eggert@gmx.de>
Tested-by: Nick Warne <nick@ukfsn.org>
Received-from: Borislav Petkov <petkovbb@googlemail.com>
[bart: keep "audio" quirks together]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Found during the (partial) unregister_netdevice audit that we didn't
have to have :)
It looks like a couple of Sun NIC drivers had unregister_netdevice
when they really meant unregister_netdev.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
move init_memory_mapping() out of init_k8_gatt.
for: http://bugzilla.kernel.org/show_bug.cgi?id=11676
2.6.27-rc2 to rc8, apgart fails, iommu=soft works, regression
This is needed because we need to map the GART aperture even
if the GATT is not initialized.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For the purpose of MTRR canonicalization, treat WRPROT as UNCACHEABLE.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The first 1M is don't care when it comes to the variables MTRRs.
Cover it as WB as a heuristic approximation; this is generally what we
want to minimize the number of registers.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Print out the correct type when the Write Protected (WP) type is seen.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fixed audio clicking problem which could be heard when using analog tv or composite input
Signed-off-by: Wiktor Grebla <greblus@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct firmware type to MTS
Correct audio routing for composite/s-video
Add DVB-T detection.
This patch uses the eeprom hash method for detection as the vendor/product
ids are also used for the DIGIVOX_AD. This may be a clone of the same
product. Explanatory text has been added prior to the hask look-up in
anticipation that it may help others.
The following has been tested to work:
Analogue TV (PAL-I)
Composite In
DVB-T (UK Crystal Palace)
USB AUDIO
The following has not been tested but probably works:
S-Video In
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes auto gain functional on 04fc:0561.
Signed-off-by: Shane <gnome42@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a buffer overflow in drivers/media/video/uvc/uvc_ctrl.c:
INFO: 0xf2c5ce08-0xf2c5ce0b. First byte 0xa1 instead of 0xcc
INFO: Allocated in uvc_query_v4l2_ctrl+0x3c/0x239 [uvcvideo] age=13 cpu=1 pid=4975
...
A fixed size 8-byte buffer is allocated, and a variable size field is read
into it; there is no particular bound on the size of the field (it is
dependent on hardware and configuration) and it can overflow [also
verified by inserting printk's.]
The patch attempts to size the buffer to the correctly.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The array size of 'shadow' still needs to be fixed in order to not overflow when reading register 0x00.
Thanks to Oliver Endriss for pointing that out.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Different backends have different input busses (saa7146, flexcop).
To reflect that a config-option to the s5h1420-driver was added which makes
the output mode selectable.
Furthermore the s5h1420-driver is now doing the same i2c-method as it was done
before adding support for other i2c-users.
This patch needs to go into the current release of the kernel, as this driver
is currently broken.
(Thanks to Eberhard Kaltenhaeuser for helping out to debug this issue.)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions dvb_dmxdev_section_callback, dvb_dmxdev_ts_callback,
dvb_dmx_swfilter_packet, dvb_dmx_swfilter_packets, dvb_dmx_swfilter and
dvb_dmx_swfilter_204 may be called from both interrupt and process
context. Therefore they need to be protected by spin_lock_irqsave()
instead of spin_lock().
This fixes a deadlock discovered by lockdep.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2040:5510 is the same hardware as 2040:5500
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The AMD ATI TV Wonder 600 has an XC3028L and *not* an XC3028, so we need to
load the proper firmware to prevent the device from overheating.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zr36067 driver is improperly declaring pixel format RGBP twice,
once as "16-bit RGB LE" and once as "16-bit RGB BE". The latter is
actually RGBR. Fix the code to properly map both pixel formats.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
sparc32 allmodconfig:
drivers/media/video/cafe_ccic.c: In function 'cafe_setup_siobuf':
drivers/media/video/cafe_ccic.c:1192: error: implicit declaration of function 'PAGE_ALIGN'
drivers/media/video/cafe_ccic.c: At top level:
drivers/media/video/cafe_ccic.c:1430: error: variable 'cafe_v4l_vm_ops' has initializer but incomplete type
drivers/media/video/cafe_ccic.c:1431: error: unknown field 'open' specified in initializer
drivers/media/video/cafe_ccic.c:1431: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1431: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c:1432: error: unknown field 'close' specified in initializer
drivers/media/video/cafe_ccic.c:1433: warning: excess elements in struct initializer
drivers/media/video/cafe_ccic.c:1433: warning: (near initialization for 'cafe_v4l_vm_ops')
drivers/media/video/cafe_ccic.c: In function 'cafe_v4l_mmap':
drivers/media/video/cafe_ccic.c:1444: error: 'VM_WRITE' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1444: error: (Each undeclared identifier is reported only once
drivers/media/video/cafe_ccic.c:1444: error: for each function it appears in.)
drivers/media/video/cafe_ccic.c:1444: error: 'VM_SHARED' undeclared (first use in this function)
drivers/media/video/cafe_ccic.c:1461: error: 'VM_DONTEXPAND' undeclared (first use in this function)
This build breakage is caused by some header file shuffle in linux-next. But
I suggest that this patch be merged ahead of linux-next to avoid bisection
breakage.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zr36067 driver should return the actual bytes-per-line value when
queried with ioctl VIDIOC_G_FMT, instead of 0. Otherwise user-space
applications can get confused.
Likewise, with ioctl VIDIOC_S_FMT, we are supposed to fill the
bytes-per-line value. And we shouldn't fail if the caller sets the
initial value to something different from 0. This is perfectly valid
for applications to pre-fill this field with the value they expect.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restore the default pixel format to YUYV as it used to be before
kernel 2.6.23. It was accidentally changed to BGR3 by commit
603d6f2c8f.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the following crash in the bttv driver:
BUG: unable to handle kernel NULL pointer dereference at 000000000000036c
IP: [<ffffffffa037860a>] radio_open+0x3a/0x170 [bttv]
This happens because radio_open assumes that all present bttv devices
have a radio function. If a bttv device without radio and one with
radio are installed on the same system, and the one without radio is
registered first, then radio_open checks for the radio device number
of a bttv device that has no radio function, and this breaks. All we
have to do to fix it is to skip bttv devices without a radio function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CS2102K stop streaming on setlightfreq (50Hz & 60Hz).
Disable it for now until a correct solution is found.
Signed-off-by: Costantino Leandro <le_costantino@pixartargentina.com.ar>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Earlier fixes to get the tuner audio working correctly broke the audio
on the Compro VideoMate H900 cards. This is now fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After commit 968de4f ("i386: Relocatable kernel support") IMAGE_OFFSET wasn't
actually used anymore in the (current) X86 build system. Now remove its last
traces.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Since v.2.6.23 DEF_INITSEG and DEF_SETUPSEG are unused. Commit c397368
("Remove old i386 setup code") dropped their usage for i386. They did not
return in the x86 tree. (Something similar must have happened for x86_64.)
Remove these.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevents: check broadcast tick device not the clock events device
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: correct segfault in generation of 32-bit reloc kernel
