zfcp_fsf_req_create assigns the same value twice to req_seq_no.
Remove one assignment and move the req_id and seq_no assignments to
one place.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
0 is a valid value for a LUN. It is slightly confusing to also see 0
in the trace entries relating to adapter and port. Change this to use
0xFFFFFFFFFFFFFFFF in the LUN field when the trace entry does not
relate to a LUN or unit.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The smatch tool from http://repo.or.cz/w/smatch.git warns about this:
drivers/s390/scsi/zfcp_scsi.c +64 zfcp_scsi_command_fail(5) warn: variable dereferenced before check 'scpnt->device'
drivers/s390/scsi/zfcp_scsi.c +64 zfcp_scsi_command_fail(5) warn: variable dereferenced before check 'scpnt->device->host'
drivers/s390/scsi/zfcp_scsi.c +93 zfcp_scsi_queuecommand(23) warn: variable dereferenced before check 'unit'
Fix the first two warnings by removing the checks for scpnt->device
and -> host: As long as the SCSI command exists, there is also a
scsi_device and a Scsi_Host.
Fix the last warning by removing the BUG_ON checks in
zfcp_scsi_queuecommand, they are leftovers from previous paranoia
about wrong pointers between data structures.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the unused payload field from the struct zfcp_dbf_san_record,
saving some space in the SAN trace.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On a link down, the adapter reopen is not strictly necessary, but it
helps flushing pending requests as quickly as possible. Add a comment
mentioning this.
qdio returning a problem on the response queue is an unlikely event.
The recovery mentioned in the comment might resolve it, so implement
it. This also has the advantage that it creates an entry in the
recovery trace to see if and when this is occurring.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the code for tracking FSF requests to new file to have this code
in one place. The functions for adding and removing requests on the
I/O path are already inline. The alloc and free functions are only
called once, so it does not hurt to inline them and add them to the
same file.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Always use the FSF request id as a reference to the FSF request. With
this change the function zfcp_reqlist_find_safe is no longer needed
and can be removed.
Reviewed-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Incorrect initialization of lport stats in fnic_probe() causes fnic to
crash at bootup and a node hang if fip is enabled and all links are brought
up after fnic is loaded.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Venkata Siva Vijayendra Bhamidipati <vbhamidi@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To enable FIP support in fnic, we have to register with hardware to receive
FIP solication frames on a well-known multicast address.
Before FIP support, the firmware interface allowed multicast address
registrations only for enic devices. This is a minor change in fnic to
allow the firmware interface to now register mcast addresses for fnic too.
Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Herman Lee <hermlee@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently we're gracefully tearing down each active connection
when fcoe.ko is removed. We shouldn't allow the user to destroy
connections by removing the module. We should force the user to
destroy each connection and then the module can be removed.
This patch makes it so a refrerence count on the module is taken
each time a fcoe_interface is created. The reference count
is dropped when the fcoe_interface is destroyed. This makes it
so that module_exit() doesn't get called unless all fcoe_interfaces
have been destroyed.
This patch leaves the removal of interfaces in the module_exit
routine so that if the user does a 'rmmod -f' we'll clean everything
up before removing the module.
The module_put line was put before the out_putdev goto line because
we should only be decrementing the reference count if a
fcoe_interface is actually destroyed. If we can't find the netdev
or the fcoe_interface then it's assumed that something else has
destroyed the fcoe_interface and it would have decremented the
reference count at that time.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libfcoe module doesnt send port keep alive every
FIP_VN_KA_PERIOD due to improper assignment of timeout value.
Update the port_ka_time appropriately by incrementing it by
FIP_VN_KA_PERIOD in fcoe_ctlr_timeout(), so that the link_work
is scheduled to send the port LKA.
Signed-off-by: Bhanu Gollapudi <bprakash@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix NULL pointer dereference crash occurs in fc_lport_bsg_request()
for bsg requests that do not contain a response request.
Specifically, FC_BSG_HST_ADD_RPORT and FC_BSG_HST_DEL_RPORT bsg
requests are not guaranteed to include a response request.
Signed-off-by: Hugh Daschbach <hdasch@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Both PLOGI and RTV response processing conditionally scale e_d_tov,
but use different scaling factors. The scaling factor is correct in
RTV response processing. Bring PLOGI e_d_tov scaling in line with RTV
common service parameter inspection.
Signed-off-by: Hugh Daschbach <hdasch@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adds check to call fc_fcp_ddp_setup for only FCP read cmds to avoid
accessing junk fsp pointer at least in ESX since non FCP frame had
junk fsp value, though fsp is implicitly initialized to null
by __alloc_skb but with this patch no more relying on fsp
initialized to null value and hitting junk fsp ptr access.
Removes fsp pointer checking in fc_fcp_ddp_setup as this is not
needed any more since its only caller for FCP read will always
have a valid fsp.
Reported by: Frank Zhang <frank_1.zhang@intel.com>
Reported by: Rob Love <robert.w.love@intel.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Use the hbalock when changing the fc_flag.
- Use the host_lock when changeing the sli_flag.
- Prevent NULL pointer dereference after dma_alloc_coherent failure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Convert all sysfs parameters to uint instead of int.
- Add lpfc_supress_link_up parameter.
- Change link_state to writable sysfs parameter.
- Add support to be able to "up" or "down" link from link_state parameter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add support for the INTF (Interface) PCI register.
- Add support for greater than 2 page SGLs.
- Add support for up to 32 bit BDE lengths.
- Implement the Port Capabilities Mailbox command.
- Stop checking the Minor Code in the EQE structure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Call pci_save_state() after pci_restore_state() call to cope
with kernel change.
- Add support for PCI BAR region 0 if BAR0 is a 64 bit register.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy.
GPIO_64 is connected to the PHY reset pin.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As reported by Alexey Dobriyan:
--------------------
setkey now takes several seconds to run this simple script
and it spits "recv: Resource temporarily unavailable" messages.
#!/usr/sbin/setkey -f
flush;
spdflush;
add A B ipcomp 44 -m tunnel -C deflate;
add B A ipcomp 45 -m tunnel -C deflate;
spdadd A B any -P in ipsec
ipcomp/tunnel/192.168.1.2-192.168.1.3/use;
spdadd B A any -P out ipsec
ipcomp/tunnel/192.168.1.3-192.168.1.2/use;
--------------------
Obviously applications want the events even when the table
is empty. So we cannot make this behavioral change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds half-duplex specific setup code (taken from SiS own GPL driver).
Without those, half-duplex connections are very unreliable, often
working on small transfers and failing after a while.
Signed-off-by: Riccardo Ghetta <birrachiara@tin.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The n-tuple list should be flushed if and only if the ETH_RESET_FILTER
flag is set and the driver is able to reset filtering/flow direction
hardware without also resetting a component whose flag is not set.
This test is best left to the driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated release version and date: 1.52.1-6 and 2010/02/16
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to the new firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware version (5.2.13).
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Use the last unicast entry in CAM in bnx2x_test_int(). Relevant for 57710 only.
Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Do not allow enabling LRO if disable_tpa=1.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: clean up MCP state in case of error in bnx2x_init_hw().
Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix: Properly release allocated MSI-X/MSI vectors if ifup failed
due to lack of memory.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert from:
if (netif_msg_<foo>(priv))
dev_<level>(dev...
to
netif_<level>(priv, foo, dev...
Also convert a few:
if (i < REG_TIMEOUT) {
etc...
return ret;
}
to
if (i >= REG_TIMEOUT)
goto fail;
etc...
return ret;
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are too similar to the dev_<level> equivalents
but take a usbnet * argument. Convert them to the recently
introduced netdev_<level> macros and remove the old macros.
The old macros had "\n" appended to the format string.
Add the "\n" to the converted uses.
Some existing uses of the dev<foo> macros in cdc_eem.c
probably mistakenly had trailing "\n". No "\n" added there.
Fix net1080 this/other log message inversion.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flush compl (compl with numfrags == 0; no data) is rcvd
from hw to indicate completion of RXQ destory operation. Fix
the RX path to not process it as RX data.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce unlikely() for skb alloc failure and vlanf checks...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some servers we see the cleaning of the RX queue finish before all
the loopback packets are sent out. This delay allows the queues to
settle before checking for successful completion.
Also, delay completion so link has time to come back up.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use local copy of current mac address when initializing. In bonding
testing we saw cases where dev_addr was out of data causing failover
errors.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was found with pings that were large enough to span multiple rx
buffers. The split frame logic handles this case nicely.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A userland command to set the LLTEMAC MAC address,
i.e. "ifconfig eth0 hw addr xx:yy:zz:pp:dd:qq",
results in a device address of 00:01:xx:yy:zz:pp.
Correct this.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLTEMAC V1 cores place only received packet length in the app4 word.
V2 cores place additional information in app4.
Mask out the additional information when retrieving the packet length.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced a new function to do the mc list processing, makes code
clearer after transition.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2eff25c18c
(netfilter: xt_hashlimit: fix race condition and simplify locking)
added a mutex deadlock :
htable_create() is called with hashlimit_mutex already locked
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
