When reading IF_AGC_GAIN register a wrong value for the base address
register was used (STB0899_DEMOD instead of STB0899_S2DEMOD). That
lead to a wrong signal strength value on DVB-S2 transponders.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_read_status the FE_HAS_SIGNAL flag was not set in case of a
successful carrier lock. This change fixes that.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b2a29b578d sets accidentally
supported delivery systems as DVB-T/T2 whilst it should be
DVB-S/S2. Due to that frontend cannot be used at all.
Reported-by: Jiří Zelenka <klacek@bubakov.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
PXA's SSP engine fails to take its current channel phase into account
when enabling a stream while the engine is already running. This
results in randomly swapped left/right channels on either the record
or the playback side, depending on which one was enabled first.
The following patch fixes this by factoring out the bit field
modifications in question to a separate function that pauses the
engine temporarily, modifies the bits and kicks it off again
afterwards. Appearantly, a transition of SSCR0_SSE syncs both
directions properly.
The patch has been rolled out to quite a number of devices over the
last weeks and seems to fix the issue reliably.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
... so that checkpatch can chill out.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Correct their formulation, replace per-family functions with a single,
unified lookup table.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
This MC1 error signature is called differently now, fix it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Use "System Read Data Error" as a more general name for MC0 bus errors
on F15h and update some error definitions.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Reviewed-by: Andreas Herrmann <andreas.herrmann3@amd.com>
These const tables are currently marked __devinitdata, but
Documentation/PCI/pci.txt says:
"o The ID table array should be marked __devinitconst; this is done
automatically if the table is declared with DEFINE_PCI_DEVICE_TABLE()."
So use DEFINE_PCI_DEVICE_TABLE(x).
Based on PaX and earlier work by Andi Kleen.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The original scrub rate API definition states that if scrub rate
accessors are not implemented, a negative value (-1) should be written
to the sysfs file (/sys/devices/system/edac/mc/mc<N>/sdram_scrub_rate,
where N is the memory controller number on the system). This is
counter-intuitive and awkward at the very least because, when setting
the scrub rate, userspace has to write to sysfs and then read it back to
check error status of the operation.
As Tony notes, best it would be to not have the sdram_scrub_rate in
sysfs if scrub rate support is not implemented. It is too late about
that and a bunch of drivers on a bunch of arches would need to be
changed and tested which is not a trivial task ATM.
Instead, settle for the next best thing of returning -ENODEV when
implementation is missing and -EINVAL when there was an error
encountered while setting the scrub rate.
Reported-by: Han Pingtian <phan@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20110916105856.GA13253@hpt.nay.redhat.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Fix the following section warnings :
WARNING: vmlinux.o(.text+0x49dbc): Section mismatch in reference
from the function acpi_map_cpu2node() to the variable
.cpuinit.data:__apicid_to_node The function acpi_map_cpu2node()
references the variable __cpuinitdata __apicid_to_node. This is
often because acpi_map_cpu2node lacks a __cpuinitdata
annotation or the annotation of __apicid_to_node is wrong.
WARNING: vmlinux.o(.text+0x49dc1): Section mismatch in reference
from the function acpi_map_cpu2node() to the function
.cpuinit.text:numa_set_node() The function acpi_map_cpu2node()
references the function __cpuinit numa_set_node(). This is often
because acpi_map_cpu2node lacks a __cpuinit annotation or the
annotation of numa_set_node is wrong.
WARNING: vmlinux.o(.text+0x526e77): Section mismatch in
reference from the function prealloc_protection_domains() to the
function .init.text:alloc_passthrough_domain() The function
prealloc_protection_domains() references the function __init
alloc_passthrough_domain(). This is often because
prealloc_protection_domains lacks a __init annotation or the annotation of alloc_passthrough_domain is wrong.
Signed-off-by: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1331810188-24785-1-git-send-email-sp@numascale.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While initializing the array of csrow attribute instances, a few csrows
were uninitialized. This happened because the module only performed a
check for DRAM base ctl register0's and not DRAM base ctl register1's
chip select enable bit. There could be systems with DIMMs populated
on only single memory channel whereas the module also assumed that a
dual channel dimm had double the memory size of a single memory channel
instead of checking the memory on each channel.
This patch fixes these above issues.
Signed-off-by: Ashish Shenoy <ashenoy@riverbed.com>
Signed-off-by: Prasanna S. Panchamukhi <ppanchamukhi@riverbed.com>
Link: http://lkml.kernel.org/r/4F459CFA.5090604@riverbed.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Power domains that were off before hibernation shouldn't be turned on
during device restore, so prevent that from happening.
This change fixes up commit 65533bbf63
PM / Domains: Fix hibernation restore of devices, v2
that didn't include it by mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch adds support for enabling or disabling UDP RSS via the
ethtool -N rx-flow-hash command.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains several fixes for formatting in regards to whitespace.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes two minor issues. The first was the fact that we were
setting the return value to false twice in the set_rss_queues function.
The second is the fact that we should have been using "min_t(int," instead
of "min((int)" in set_fdir_queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The err_eeprom and err_sw_init tags both go to the same location. So
instead of maintaining two tags this patch combines them so we only use
err_sw_init.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change relocates the ixgbe_poll routine so it is right next to the
interrupt routine that schedules and calls it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change just cleans up some of the logic in the service_timer function
so that we can avoid unnecessary swapping of the ready value between true to
false and back to true.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that only the 2nd cache line in the ring structure
should see frequent updates. The advantage to this is that it should
reduce the amount of cross CPU cache bouncing since only the 2nd cache line
will be changing between most network transactions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we store the tx_flags and protocol information
to the tx_buffer_info structure sooner. This allows us to avoid unnecessary
read/write transactions since we are placing the data in the final location
earlier.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If there are no unacked bad blocks, then there is no point searching
for them to acknowledge them.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In super_1_sync (the first hunk) we need to clear 'changed' before
checking read_seqretry(), otherwise we might race with other code
adding a bad block and so won't retry later.
In md_update_sb (the second hunk), in the case where there is no
metadata (neither persistent nor external), we treat any bad blocks as
an error. However we need to clear the 'changed' flag before calling
md_ack_all_badblocks, else it won't do anything.
This patch is suitable for -stable release 3.0 and later.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Be redefining ->chunkshift as the shift from sectors to chunks rather
than bytes to chunks, we can just use "bitmap->chunkshift" which is
shorter than the macro call, and less indirect.
Signed-off-by: NeilBrown <neilb@suse.de>
These funcitons don't add anything useful except possibly the trace
points, and I don't think they are worth the extra indirection.
So remove them.
Signed-off-by: NeilBrown <neilb@suse.de>
There is nothing gained by holding a lock while we check if a pointer
is NULL or not. If there could be a race, then it could become NULL
immediately after the unlock - but there is no race here.
So just remove the locking.
Signed-off-by: NeilBrown <neilb@suse.de>
The use of a goto makes the control flow more obscure here.
So make it a normal:
if (x) {
Y;
}
No functional change.
Signed-off-by: NeilBrown <neilb@suse.de>
The part of /proc/mdstat which describes the bitmap should really
be generated by code in bitmap.c. So move it there.
Signed-off-by: NeilBrown <neilb@suse.de>
'resizing' an array in this context means making use of extra
space that has become available in component devices, not adding new
devices.
It also includes shrinking the array to take up less space of
component devices.
This is not supported for array with a 'far' layout. However
for 'near' and 'offset' layout arrays, adding and removing space at
the end of the devices is easy to support, and this patch provides
that support.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.
So create a raid1 merge_bvec_fn to check that function in children
as well.
This introduces a small problem. There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request. So a
device added between these could end up getting a request which
violates its merge_bvec_fn.
Currently the best we can do is synchronize_sched(). This will work
providing no preemption happens. If there is is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.
So enhance the raid10 merge_bvec_fn to check that function in children
as well.
This introduces a small problem. There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request. So a
device added between these could end up getting a request which
violates its merge_bvec_fn.
Currently the best we can do is synchronize_sched(). This will work
providing no preemption happens. If there is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NeilBrown <neilb@suse.de>
These personalities currently set a max request size of one page
when any member device has a merge_bvec_fn because they don't
bother to call that function.
This causes extra works in splitting and combining requests.
So make the extra effort to call the merge_bvec_fn when it exists
so that we end up with larger requests out the bottom.
Signed-off-by: NeilBrown <neilb@suse.de>
md.h has an 'rdev_for_each()' macro for iterating the rdevs in an
mddev. However it uses the 'safe' version of list_for_each_entry,
and so requires the extra variable, but doesn't include 'safe' in the
name, which is useful documentation.
Consequently some places use this safe version without needing it, and
many use an explicity list_for_each entry.
So:
- rename rdev_for_each to rdev_for_each_safe
- create a new rdev_for_each which uses the plain
list_for_each_entry,
- use the 'safe' version only where needed, and convert all other
list_for_each_entry calls to use rdev_for_each.
Signed-off-by: NeilBrown <neilb@suse.de>
If RAID1 or RAID10 is used under LVM or some other stacking
block device, it is possible to enter a deadlock during
resync or recovery.
This can happen if the upper level block device creates
two requests to the RAID1 or RAID10. The first request gets
processed, blocks recovery and queue requests for underlying
requests in current->bio_list. A resync request then starts
which will wait for those requests and block new IO.
But then the second request to the RAID1/10 will be attempted
and it cannot progress until the resync request completes,
which cannot progress until the underlying device requests complete,
which are on a queue behind that second request.
So allow that second request to proceed even though there is
a resync request about to start.
This is suitable for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Ray Morris <support@bettercgi.com>
Tested-by: Ray Morris <support@bettercgi.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When commit 69e51b449d (md/bitmap: separate out loading a bitmap...)
created bitmap_load, it missed calling it after bitmap_create when a
bitmap is created through the sysfs interface.
So if a bitmap is added this way, we don't allocate memory properly
and can crash.
This is suitable for any -stable release since 2.6.35.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
It seems that with recent kernel, writeback can still be happening
while shutdown is happening, and consequently data can be written
after the md reboot notifier switches all arrays to read-only.
This causes a BUG.
So don't switch them to read-only - just mark them clean and
set 'safemode' to '2' which mean that immediately after any
write the array will be switch back to 'clean'.
This could result in the shutdown happening when array is marked
dirty, thus forcing a resync on reboot. However if you reboot
without performing a "sync" first, you get to keep both halves.
This is suitable for any stable kernel (though there might be some
conflicts with obvious fixes in earlier kernels).
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is failed (some data inaccessible) then there is no
point attempting to add a spare as it could not possibly be recovered.
However that may be value in re-adding a recently removed device.
e.g. if there is a write-intent-bitmap and it is clear, then access
to the data could be restored by this action.
So don't reject a re-add to a failed array for RAID10 and RAID5 (the
only arrays types that check for a failed array).
Signed-off-by: NeilBrown <neilb@suse.de>
Add support for temperature offset registers for CPUTIN, SYSTIN,
and AUXTIN temperatures.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
We don't really use or need separate device IDs for the various JC42.4 compliant
chips, so remove them and just stick with jc42.
Also update a datasheet references for SE98A, STTS424, and STTS424E02.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
ZL9101M and ZL9117M are compatible to ZL6100. Add support to the zl6100 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add PMBUS_VIRT_READ_TEMP_AVG, PMBUS_VIRT_READ_TEMP2_AVG,
PMBUS_VIRT_READ_POUT_AVG, PMBUS_VIRT_READ_POUT_MAX,
and PMBUS_VIRT_RESET_POUT_HISTORY.
We'll need those for MAX34446.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
